MTD S235 - Manuals

5 Operation 1. Do not put hands or feet near rotating parts, in the auger/im- peller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may c...

6 NOTE: This Operator’s Manual covers several models. Snow thrower features vary by model. Not all features discussed in this manual are applicable to all snow thrower models. NOTE: All references to left or right side of the snow thrower is from the operating position only Contents of Carton Carton...

8 Before Starting WARNING: Before starting the engine, read, understand, and follow all instructions and warnings on the machine and in this manual. Positioning the Discharge Chute 1. Loosen the wing knob found on the left side of the discharge chute and pivot the upper chute upward or downward to t...

9 5. If you have a grounded three-prong receptacle, proceed as follows. 6. Move Choke Control to the “Full” position.7. Push Primer three (3) times, making sure to cover vent hole when pushing. 8. Connect power cord to switch box on dash panel. Plug the other end of power cord into a three-prong 120...

10 WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual. Shave Plate 1. To check the adjustment of the shave plate, place the...

11 Before servicing, repairing, or inspecting, disengage the control bail and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. WARNING 6 Adjustments & Maintenance Figure 9 IMPORTANT:...

12 4. Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Cover spark plug hole with a rag and crank the engine several times to distribute the oil. Replace spark plug. NOTE: Refer to the engine manual for more information on preparing the snow t...

13 Please do NOT return the unit to the retailer from which it was purchased, without first contacting Customer Support. Log onto www.whiteoutdoor.com or call a customer service representative at 1(800) 949-4483 8 Trouble- Shooting Note: You will need the model number and serial number if and when ca...

15 REF NO. PART No. DESCRIPTION Qty. 1 629-0236 Extension Cord 1 2 710-0627 Hex Screw, 5/16-24 x .75 1 6 710-1003 Screw, #10-16 x .625 2 4 710-3025 Hex Screw, 5/16-18 x .625 4 5 712-04063 Hex Flange Lock Nut, 5/16-18 2 6 725-0157 Push Mount Cable Tie 1 7 726-0154 Push Mount Cable Tie 1 8 726-0205 Cl...

16 9 Part List: Snow Thrower For parts and/or accessories please call 1-800-949-4483 www.whiteoutdoor.com 1 16 25 25 27 26 28 29 27 37 35 3 4 15 8 5 6 34 22 17 7 2 36 14 32 21 20 33 19 31 30 27 29 10 11 12 18 24 4 13 9 23 38

18 10 Accessories & Kits The following accessories and kits are available for single-stage, two-cycle snow throwers. See the retailer from which you purchased your snow thrower, an authorized MTD Service Dealer or phone (800) 800-7310 for information regarding price and availability MODEL DESCRI...

The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its posses-sions and territories.“MTD” warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original ...