MTD 462 thru 464 - Manuals - manualsarea.com

Page 2 - Finding and Recording Model Number; Model Number; Please do; Table of Contents; Customer Support Representative

2 Finding and Recording Model Number Model Number Serial Number Please do NOT return the unit to the retailer from which it was purchased, without ﬁrst contacting Customer Support. Table of Contents BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT, please locate the model plate on the equipment and co...

Page 3 - WARNING; Your Responsibility

3 1 Safety Labels WARNING This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at-tempting to operate this machine. Failure to comply with these i...

Page 4 - Training

4 2 Safe Operation Practices Training 1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. 2. Be familiar with all controls...

Page 5 - Safe

5 Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of...

Page 6 - Loose Parts In Carton; IMPORTANT

6 3 Setting Up Your Chipper Shredder IMPORTANT : This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine. Loose Parts In Carton a. Hopper Assembly d. Bagb. Chute Deflector...

Page 7 - Attaching The Chipper Chute; Setting Up

7 Figure 5 3 Figure 6 Figure 7 b. Place second spacer over hex bolt inside other hinge and secure with hex lock nut. c. Secure both sides of chute deflector to impeller housing using wing knobs previously removed. Attaching The Chipper Chute 5. a. Remove the three cupped washers and hex nuts from we...

Page 8 - Chipper Chute; Never; fuel; Know Your Chipper Shredder

8 4 Operating Your Chipper Shredder Now that you have set up your chipper shredder for operation, get aquainted with its controls and features. These are described below and illustrated on this page. This knowledge will allow you to use your new equipment to its fullest potential. Chipper Chute Allo...

Page 9 - Never run the engine; Stopping Engine; Using The Chipper Shredder; Operating

9 4 WARNING Never run the engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Starting Engine WARNING: Never run the engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monox-ide, an odorless and deadly gas. 1....

Page 11 - Storing Your Chipper Shredder

11 5 WARNING Figure 13 Figure 14 The impeller’s chipper blades and shredder blade are sharp. Wear leather work gloves to protect your hands. Maintaining Your Chipper Shredder IMPORTANT Make certain chipper blades are reassem-bled with the sharp edge facing upward. Torque hardware to 250 - 300 in. lb...

Page 12 - Trouble; Cause

12 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position (if equipped). 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped)....

Page 15 - Parts List

15 7 Parts List 1. 736-0217 Lock Washer, 3/8 2. 714-0149B Cotter Pin 3. 681-0048 Wing Knob 5/16-18 4. 681-0094 Chute Deflector Assembly 5. 711-0835 Clevis Pin 6. 781-0457 Shredder Screen 7. 726-0211 U-Nut 5/16-18 8. 750-0793 Spacer 9. 712-3027 Hex Lock Nut 1/4-20 10. 712-3004A Hex Lock Nut 5/16-18 1...

Page 20 - MANUFACTURER’S LIMITED WARRANTY FOR

The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its posses-sions and territories.“MTD” warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original ...