Moxa G2150I - Manuals - manualsarea.com

Page 2 - OnCell G2150I AT Command Set; accordance with the terms of that agreement.; Copyright Notice; Copyright; Trademarks; MOXA is a registered trademark of The Moxa Group.; Disclaimer

OnCell G2150I AT Command Set The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright © 2007 Moxa Technologies Co., Ltd. All rights reserved. Reproduction without permission is prohibi...

Page 3 - Table of Contents; Chapter 1

Table of Contents Chapter 1 Introduction ..................................................................................................1-1 Scope of the Document ............................................................................................................ 1-2 Related Documents .......

Page 7 - Introduction

1 1 Chapter 1 Introduction This chapter is an introduction to the OnCell G2150I AT Command Set. The following topics are covered: Scope of the Document Related Documents ETSI Secretariat Abbreviations Definitions Presentation Rules

Page 9 - Abbreviations

OnCell G2150I AT Command Set Introduction 1-3 Abbreviations ADN Abbreviated Dialing Number (Phonebook) AMR Adaptive Multi-Rate AMR-FR AMR Full Rate (full rate speech Version3) AMR-HR AMR Half Rate (half rate speech version 3) AOC Advice Of Charge ASCII Standard characters table (1 byte coding) AT Mo...

Page 10 - Definitions; TE

OnCell G2150I AT Command Set Introduction 1-4 Definitions The words “Mobile Station” (MS) or “Mobile Equipment” (ME) are used for mobile terminals that support GSM services. Terminal Equipment (TE) is the Human Machine Interface (HMI) of a GSM device (modem or handset). TE can be a handset HMI or th...

Page 11 - AT Command Features; Serial Line Settings

2 2 Chapter 2 AT Command Features This chapter includes information about the AT Command Features of the OnCell G2150I. The following topics are covered in this chapter: Serial Line Settings Command Line Information Response and Result Codes

Page 12 - data bits; Command Line; If the command syntax is incorrect, the “ERROR” string is returned.

OnCell G2150I AT Command Set AT Command Features 2-2 Serial Line Settings A serial link handler is configured with the following default values (factory settings): y 115200 bps y 8 data bits y 1 stop bit y no parity y RTS/CTS flow control Use the +IPR, +IFC, and +ICF commands to change these setting...

Page 13 - General Commands

3 3 Chapter 3 General Commands This chapter includes information about the General Commands of the OnCell G2150I. The following topics are covered in this chapter: Manufacturer Identification: +CGMI Request Model Identification: +CGMM Request Revision Identification: +CGMR Product Serial Num...

Page 14 - Command syntax; No parameters

OnCell G2150I AT Command Set General Commands 3-2 Manufacturer Identification: +CGMI Description: This command gives the manufacturer identification. Command syntax: AT+CGMI Command Possible Responses AT+CGMI Note: Get manufacturer identification WAVECOM MODEM OK Note: Command valid, Wavecom modem D...

Page 20 - OK; The user shall then take care of processing SIM

OnCell G2150I AT Command Set General Commands 3-8 AT+CCLK? Note: Get current date and time +CCLK: “00/06/09, 17:34:23” OK Note: current date is June 9 th , 2000 current time is 5:34:23 pm Defined values: <date and time string> String format for date/time is: “yy/MM/dd,hh:mm:ss”. Valid years ar...

Page 21 - Second Byte Value warning:

OnCell G2150I AT Command Set General Commands 3-9 Command Possible responses AT+CSIM= <length>,<command> +CSIM : <length>,<response> +CME ERROR : <err> AT+CSIM? OK AT+CSIM=? OK Defined values: <length>: integer type Length of the characters that are sent to TE in ...

Page 24 - : indicator is OFF or in state which can be identified as “OFF” state

OnCell G2150I AT Command Set General Commands 3-12 AT+CIND? Note: read ME indicators current values +CIND: <ind>[,<ind>[,…]] OK AT+CIND? +CIND: 2,2,1,0,0,0,0 AT+ CIND=? Note: read ME indicators possible values +CIND: (<descr>,(list of supported<ind>s))[,(<descr>,(list o...

Page 25 - • Only basic option and UIH framing is supported.

OnCell G2150I AT Command Set General Commands 3-13 command is ignored and the modem will return a +CME ERROR: <err> response. Restrictions • Only basic option and UIH framing is supported. • Only convergence layers type 1 and 3 are supported. • Autobauding is not compliant with multiplexing mo...

Page 26 - Note: Get possible values

OnCell G2150I AT Command Set General Commands 3-14 Command Possible responses AT+CMUX=? Note: Get possible values MUX: (0),(0),(1-5),(1-255),(1-128),(0-255),(1-128),(1-128) OK AT+CMUX? Note: Get current values +CMUX:<mode>,<subset>,<port_speed>,<N1>,<T1>,<N2>,<...

Page 27 - Call Control Commands; The following topics are covered in this chapter:; Remote Disconnection

4 4 Chapter 4 Call Control Commands This chapter includes information about the Call Control Commands of the OnCell G2150I. The following topics are covered in this chapter: Dial Command: D Hang-Up Command: H Answer a Call: A Remote Disconnection Extended Error Report: +CEER DTMF Signals...

Page 31 - Redial Last Telephone Number: ATDL; ATDL

OnCell G2150I AT Command Set Call Control Commands 4-5 DTMF Signals: +VTD, +VTS +VTD description: The product enables the user application to send DTMF tones over the GSM network. This command is used to define tone duration (the default value is 70 ms ± 5 ms, according to 3GPP 23.014). Command synt...

Page 33 - Automatic Answer: ATS0

OnCell G2150I AT Command Set Call Control Commands 4-7 activated using +CLCK command). Voice call (with semi-colon). AT%D1 Activates automatic DTR dialing if DTR switches from OFF to ON; Dials the phone number in the first location of the ADN phonebook (or FDN phonebook, if it is activated using +CL...

Page 36 - Network Service Commands

5 5 Chapter 5 Network Service Commands This chapter includes information about the Network Service Commands of the OnCell G2150I. The following topics are covered in this chapter: Signal Quality: +CSQ Operator Selection: +COPS Network Registration: +CREG Operator List Management: +WOLM Rea...

Page 38 - Emergency call is allowed without SIM; Command; Note: Ask for current PLMN

OnCell G2150I AT Command Set Network Service Commands 5-3 +CME ERROR: 547 Emergency call is allowed without SIM Careful: Error code + CME ERROR: 546 or +CME ERROR: 547 are only returned if SIM is not present. The fact that network supports emergency calls (+CME ERROR: 547) does not imply that emerge...

Page 39 - Note: Ask for deregistration from network

OnCell G2150I AT Command Set Network Service Commands 5-4 AT+COPS=2 Note: Ask for deregistration from network OK Note: Succeeded AT+COPS? Note: Ask for current PLMN +COPS: 2 Note: ME is unregistered until <mode>=0 or 1 is selected Defined values: <mode> 0: automatic (default value) 1: ma...

Page 41 - Note: Delete an entry at location 11; Note: Give an operator in numeric format

OnCell G2150I AT Command Set Network Service Commands 5-6 AT+WOLM=0,11 Note: Delete an entry at location 11 +CME ERROR: 21 Note: Invalid index Defined values: <mode> : 0 delete 1 write 2 read <loc> : location. If this parameter is not filled with <mode>=1, the location will be the ...

Page 42 - Note: Give a wrong operator

OnCell G2150I AT Command Set Network Service Commands 5-7 AT+WOPN=0,99999 Note: Give a wrong operator +CME ERROR: 22 Note: Not found AT+WOPN=0,20801,36 Note: Give an operator in numeric format for lac 36 +WOPN: 0,”Orange F” OK Note: Alphanumeric answer AT+WOPN=3,0 Note: Erase NITZ PLMN names stored ...

Page 43 - SIM card that is used by AT+CPOL command.; Note: Ask for selection of the SIM file

OnCell G2150I AT Command Set Network Service Commands 5-8 Selection of Preferred PLMN List: +CPLS Description: This command is used to select one PLMN selector with access technology list in the SIM card that is used by AT+CPOL command. Command syntax: AT+CPLS= <List> Command Possible response...

Page 45 - Note: Select long alphanumeric format; Note: Acces technology UTRAN is selected

OnCell G2150I AT Command Set Network Service Commands 5-10 AT+CPOL=,0 Note: Select long alphanumeric format OK AT+CPOL? Note: Ask for preferred list of networks with only EF_PLMNsel present +CPOL: 1,0,”D1-TELEKOM” +CPOL: 6,0,”F SFR” OK Note: Preferred list of networks in long alphanumeric format AT+...

Page 46 - Note: Ask for preferred list of networks

OnCell G2150I AT Command Set Network Service Commands 5-11 to get the maximum index of the selected EF. <format>: 0 long alphanumeric format for <oper> 1 short alphanumeric format for <oper> 2 numeric format for <oper> <oper>: character string or integer (see <format...

Page 47 - Security Commands

6 6 Chapter 6 Security Commands This chapter includes information about the Security Commands of the OnCell G2150I. The following topics are covered in this chapter: Enter PIN: +CPIN Enter PIN2: +CPIN2 PIN Remaining Attempt Number: +CPINC Facility Lock: +CLCK Change Password: +CPWD

Page 53 - Note: Possible values

OnCell G2150I AT Command Set Security Commands 6-7 Change Password: +CPWD Description: This command is used by the application to change a password (PIN, call barring, NCK, etc.). The facility values (<fac>) are the same as for the +CLCK command with a “P2” facility to manage SIM PIN2. For the...

Page 54 - Short Message Commands; Parameter Definitions

7 7 Chapter 7 Short Message Commands This chapter includes information about the Short Message Commands of the OnCell G2150I. The following topics are covered in this chapter: Parameter Definitions Select Message Service: +CSMS New Message Acknowledgement: +CNMA Preferred Message Storage: +C...

Page 55 - SMS

OnCell G2150I AT Command Set Short Message Commands 7-2 Parameter Definitions <da> Destination Address, coded like GSM 03.40 TP-DA <dcs> Data Coding Scheme, coded like in document [5]. <dt> Discharge Time in string format: “yy/MM/dd,hh:mm:ss zz 　 ”(Year [00-99], Month [01-12], Day ...

Page 56 - Note: Possible services; Command syntax in text mode:

OnCell G2150I AT Command Set Short Message Commands 7-3 Select Message Service: +CSMS Description: The supported services are originated (SMS-MO) and terminated short message (SMS-MT) + Cell Broadcast Message (SMS-CB) services. Command syntax: AT+CSMS=<service> Command Possible responses AT+CS...

Page 57 - Note: message received

OnCell G2150I AT Command Set Short Message Commands 7-4 AT+CNMI=2,2,0,0,0 Note: <mt>=2 OK +CMT: “123456”,”98/10/01,12:30 00+00”, 129, 4, 32, 240, “15379”, 129, 5<CR><LF> Received message Note: message received Example of acknowledgement of a new message in PDU mode: Command Possibl...

Page 58 - Note: Possible message storages

OnCell G2150I AT Command Set Short Message Commands 7-5 Preferred Message Storage: +CPMS Description: This command allows the message storage area to be selected (for reading, writing, etc). Command syntax: AT+CPMS=<mem1>,[<mem2>,[<mem3>]] Command Possible responses AT+CPMS=? Note:...

Page 62 - read from the memory selected by +CPMS command.

OnCell G2150I AT Command Set Short Message Commands 7-9 1: SMS-DELIVERs are routed using unsolicited code: +CMTI: “SM”,<index> 2: SMS-DELIVERs (except class 2 messages) are routed using unsolicited code: if PDU mode: +CMT: [<alpha>], <length> <CR> <LF> <pdu> if te...

Page 63 - Note: New message received

OnCell G2150I AT Command Set Short Message Commands 7-10 Command Possible responses AT+CMTI: “SM”,1 Note: New message received AT+CMGR=1 Note: Read the message +CMGR: “REC UNREAD”, “0146290800”, “98/10/01,18:22:11+00”, <CR><LF> ABCdefGHI OK AT+CMGR=1 Note: Read the message again +CMGR: “...

Page 65 - Note: Write a message in text mode

OnCell G2150I AT Command Set Short Message Commands 7-12 +CMGS: <mr>,, OK Note: Successful transmission AT+CMGS=<length><CR> Note: Send a message in PDU mode (1/3) <pdu> Note: Enter message in PDU mode (2/3) <ctrl-Z> Note: End the message (3/3) +CMGS: <mr> OK Note...

Page 68 - Note: All messages are deleted; Note: Send a message

OnCell G2150I AT Command Set Short Message Commands 7-15 AT+CMGD=1,0 OK Note: The message from the preferred message storage at the location 1 is deleted AT+CMGD=1,1 OK Note: All READ messages from the preferred message storage are deleted AT+CMGD=1,2 OK Note: All READ messages and SENT mobile origi...

Page 69 - Select Cell Broadcast Message Types: +CSCB; allowed in both PDU and text modes.; Cell Broadcast Message Identifiers: +WCBM; This specific command is used to read the EF-CBMI SIM file.

OnCell G2150I AT Command Set Short Message Commands 7-16 Select Cell Broadcast Message Types: +CSCB Description: This command selects which types of CBMs are to be received by the ME. It is allowed in both PDU and text modes. Command syntax: AT+CSCB=<mode>, [ <mids>, [ <dcss> ] ] I...

Page 70 - Note: Write 4 message identifiers in EF- CBMI

OnCell G2150I AT Command Set Short Message Commands 7-17 AT+WCBM=“10,100,1000,10000” Note: Write 4 message identifiers in EF- CBMI OK Note: CBMIs are stored in EF-CBMI AT+WCBM? Note: Read the CBMIs in EF-CBMI +WCBM=“10,100,1000,100000” OK Note: 4 CBMIs are stored in EF-CBMI Message Status Modificati...

Page 72 - “REC

OnCell G2150I AT Command Set Short Message Commands 7-19 AT+CMGR=10 +CMGR: “REC UNREAD”,”+33660669023”,,”03/02/13,18:36:35+00”<CR><LF> Do you want to change state ? OK Note: The state hasn’t be updated AT+WUSS=0 OK +CMTI: “SM”,11 Note: SMS has been received in index 11 AT+CMGR=11 +CMGR: ...

Page 74 - Note: Read the SMS storage; Note: Disable feature

OnCell G2150I AT Command Set Short Message Commands 7-21 AT+WMCP=0 Note: Copy all the SMS from the SIM to the Flash OK AT+CPMS? Note: Read the SMS storage +CPMS: “ME”,4,99,”ME”,4,99,”SM”,4,10 OK Note: 4 SMS are stored in the flash. Defined values: <mode> Copy mode • 0: From the SIM to the Flas...

Page 75 - Data Commands; Using AT Commands During a Data Connection

8 8 Chapter 8 Data Commands This chapter includes information about the Data Commands of the OnCell G2150I. The following topics are covered in this chapter: Using AT Commands During a Data Connection Bearer Type Selection: +CBST Select Mode: +FCLASS Service Reporting Control: +CR Cellular...

Page 76 - Switch from online to offline mode:; Note: Ask for a bearer

OnCell G2150I AT Command Set Data Commands 8-2 Using AT Commands During a Data Connection To use AT Commands during a data connection (e.g., while the product is in online mode), it is necessary either to switch to offline mode, or to use the specific +WMUX command to enable Commands / Data multiple...

Page 77 - Note: Fax class 2 not supported

OnCell G2150I AT Command Set Data Commands 8-3 6 4800 bps (modem type: V.32) 7 9600 bps (modem type: V.32) 8 Specific 12 9600 bps (modem type: V.34) 14(*) 1400 bps (modem type: V.34) 65 300 bps (modem type: V.110) 66 1200 bps (modem type: V.110) 68 2400 bps (modem type: V.110) 70 4800 bps (modem typ...

Page 82 - Back to Online Mode: O

9 9 Chapter 9 V24-V25 Commands This chapter includes information about the V24-V25 Commands of the OnCell G2150I. The following topics are covered in this chapter: Fixed DTE Rate: +IPR DTE-DCE Character Framing: +ICF DTE-DCE Local Flow Control: +IFCR Set DCD Signal: &C Set DTR Signal: ...

Page 84 - character framing used by the DCE.

OnCell G2150I AT Command Set V24-V25 Commands 9-3 DTE-DCE Character Framing: +ICF Description: This command is used to determine the local serial port start-stop (asynchronous) character framing used by the DCE. Command syntax: AT+ICF= <format>[, <parity>] Command Possible responses AT+I...

Page 85 - Note: The DTR signal is ignored

OnCell G2150I AT Command Set V24-V25 Commands 9-4 AT+IFC=0,0 OK Note: New values Defined values: < DCE_by_DTE > 0: none (supported) 1: XOn/Xoff local circuit 103 ( not supported) 2: RTS (supported) 3: Xon/Xoff global on circuit 103 (not supported) Important note: When this parameter is set to ...

Page 86 - Note: Return from offline mode to online mode; Result Code Suppression: Q; Note: DCE transmits result codes

OnCell G2150I AT Command Set V24-V25 Commands 9-5 AT&D1 Note: Modem switches from data to command mode when DTR switches from ON to OFF OK Note: Command valid AT&D2 Note: When DTR switches from ON to OFF, the call is released OK Note: Command valid Defined values: <n> 0: The DTR signal...

Page 87 - Note: Writes current configuration to EEPROM

OnCell G2150I AT Command Set V24-V25 Commands 9-6 Defined values: <n> 0: DCE transmission result code 1: Result codes are suppressed and not transmitted DCE Response Format: V Description: This command determines whether or not the DCE response format uses the header characters <CR><L...

Page 88 - Note: Characters are not echoed

OnCell G2150I AT Command Set V24-V25 Commands 9-7 Auto-tests: &T Description: This command allows the triggering of various auto-tests. Command syntax: AT&T<n> Command Possible responses AT&T0 Note: Perform software auto-tests OK Note: No software problem detected, all checksums ar...

Page 89 - Note: Ask to restore the factory settings; Note: Display active parameters in RAM

OnCell G2150I AT Command Set V24-V25 Commands 9-8 Restore Factory Settings: &F Description: This command is used to restore the factory settings from EEPROM. It only restores the parameters that can be found in paragraph 19 Codes and values (Parameters Storage paragraph) with AT&F column che...

Page 90 - Request Identification: I; information text; Note: GSM 900 MHz primary band

OnCell G2150I AT Command Set V24-V25 Commands 9-9 Request Identification: I Description: This command causes the product to transmit one or more lines of specific information text Command syntax: ATI<n> Command Possible responses ATI0 Note: Manufacturer and model identifications WAVECOM MODEM ...

Page 92 - GPRS Commands

1 1 0 0 Chapter 10 GPRS Commands This chapter includes information about the GPRS Commands of the OnCell G2150I. The following topics are covered in this chapter: Define PDP Context: + CGDCONT Quality of Service Profile (Requested): +CGQREQ Quality of Service Profile (Minimum acceptable): +CGQ...

Page 94 - Other values are reserved.

OnCell G2150I AT Command Set GPRS Commands 10-3 <PDP_address>: a string parameter that identifies the MT in the address space applicable to the PDP. If the value is null or omitted, then a value may be provided by the TE during the PDP startup procedure, or a dynamic address will be requested....

Page 97 - : Subscribed by the Nwk / default if value is omitted

OnCell G2150I AT Command Set GPRS Commands 10-6 non-sensitive application that can cope with data loss. NOTE: For real-time traffic, the QoS profile also requires appropriate settings for delay and throughput. 3: Up to 4 000 (32 kbits/s). 4: Up to 8 000 (64 kbits/s). 5: Up to 16 000 (128 kbits/s). 6...

Page 99 - PDP Context Activate or Deactivate: +CGACT

OnCell G2150I AT Command Set GPRS Commands 10-8 AT +CGATT=1 OK Defined values: <state>: indicates the state of GPRS attachment • 0: detached • 1: attached • 2: combined detach (GPRS and GSM detach in the same network request) • Other values are reserved and will result in an ERROR response to ...

Page 101 - Select Service for MO SMS Messages: +CGSMS

OnCell G2150I AT Command Set GPRS Commands 10-10 AT+CGCLASS=? +CGCLASS: (“CG”,”CC”) OK AT+CGCLASS? +CGCLASS: “CC” OK Defined values: <class>: a string parameter that indicates the GPRS mobile class (in descending order of functionality) ‧ A class A (highest) ‧ B class B ‧ CG class C in GPRS on...

Page 103 - ME; GPRS Network Registration Status: +CGREG

OnCell G2150I AT Command Set GPRS Commands 10-12 mode), if MT result code buffer is full, the oldest ones can be discarded. Defined events: The following unsolicited result codes and the corresponding events are defined: +GEV: REJECT <PDP_type>, <PDP_addr> A network request for PDP conte...

Page 104 - Request GPRS IP Service: ‘D’

OnCell G2150I AT Command Set GPRS Commands 10-13 2: enable network registration and location information unsolicited result code +CGREG: <stat>[,<lac>,<ci>] <stat>: 0: not registered, ME is not currently searching a new operator to register to 1: registered, home network 2: n...

Page 105 - Network Requested PDP Context Activation; The +CGAUTO command is used to select modem compatibility mode.

OnCell G2150I AT Command Set GPRS Commands 10-14 Network Requested PDP Context Activation In this mode of operation, the MT behaves like an answering modem and accepts the normal V.25ter commands associated with answering a call. If GPRS-specific configuration commands are required, they may be sent...

Page 107 - The PDP type must match exactly.; reject the request; Example

OnCell G2150I AT Command Set GPRS Commands 10-16 During the PDP startup procedure the MT has the PDP type and the PDP address provided by the network in the Request PDP Context Activation message. If a <cid> is given its information must match the PDP type and PDP address in the network reques...

Page 110 - Note: choose GPRS multislot class 8

OnCell G2150I AT Command Set GPRS Commands 10-19 GPRS Parameter Customization: + WGPRS Description: This command modifies some G2150I GPRS parameters: ‧ the ATTACH-STATUS (the ME does or not perform automatically a GPRS attachment after initialization), ‧ the PDP-INIT-STATUS (activates automatically...

Page 112 - Full AT GPRS Command Examples; Activation of an IP PDP context :

OnCell G2150I AT Command Set GPRS Commands 10-21 some OS-specific frames, for accurate transfer rate measurements. <parameter>: a numeric parameter that controls the operation defined by <mode> if it is equal to 0, 1, 2, or 3. 0 operation OFF (disabled) 1 operation ON (enabled) <cid&g...

Page 113 - Data transfer

OnCell G2150I AT Command Set GPRS Commands 10-22 Example 2: AT+CGCLASS=”CG” OK +CGREG: 1 AT +CGDCONT=1,”IP”,”internet” OK AT +CGQREQ=1,1,4,5,2,14 OK AT +CGQMIN=1,1,4,5,2,14 OK AT +CGATT=1 OK AT +CGACT=1,1 OK Remark about +CGDATA : The goal of this command is the same as ATD*99***AT + CGDATA=1 CONNEC...

Page 114 - MOXA Proprietary Commands

1 1 1 1 Chapter 11 MOXA Proprietary Commands This chapter includes information about the MOXA proprietary Commands of the OnCell G2150I. The following topics are covered in this chapter: Firmware Upgrade: *UPG Restore Default Setting: *DEFAULT Automatic PIN Entry: *USEPIN Initial Strings: *B...

Page 115 - NOTE

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-2 Firmware Upgrade: *UPG Description: This command triggers a X-modem(checksum) downloading session for G2150I firmware image. . Notes: • There will always be risks when performing the firmware upgrade. Ensure to have fixed physical connectio...

Page 116 - This command resets the G2150I to its factory default.

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-3 Restore Default Setting: *DEFAULT Description: This command resets the G2150I to its factory default. Example AT* DEFAULT *DEFAULT: reset modem configurations Restoring modem defaults, please wit… OK Clean-up, please wait… Clean-up OK All D...

Page 117 - Note: 1234 is an example of PIN code

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-4 Automatic PIN Entry: *USEPIN Description: This command enables/disables the automatic PIN code entry function when G2150I is booting up Command syntax: AT*USEPIN=<n>, <PIN Code> Command Possible responses AT*USEPIN=1, 1234 Note:...

Page 118 - Note: List all status

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-5 Initial Strings: *BOOTSTR Description: This command enables/disables the initial strings Command syntax: AT*BOOTSTR=<m> AT*BOOTSTR<n>=<initial strings> Command Possible responses AT*BOOTSTR=1 OK Note: Done AT*BOOTSTR=0 OK ...

Page 119 - This command configures the serial port settings

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-6 Serial Port Configuration: *SERIAL Description: This command configures the serial port settings Command syntax: AT*SERIAL=<n>,<baudrate>,<data bits>,”<parity>“,<stop bits>,”<flow control>“ Command Possib...

Page 120 - This command configures the SMS Tunnel mode settings

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-7 SMS Tunnel Mode: *SMS Description: This command configures the SMS Tunnel mode settings Command syntax: AT*SMSIN=<encoding>,<receive phone 1>,<receive phone 2> AT*SMSOUT=<encoding>,<target phone 1>,<target p...

Page 121 - Configured

OnCell G2150I AT Command Set MOXA Proprietary Commands 11-8 *SMSOUT: Configured Encode: 7-Bits GSM Text Receiver1: +886289191230 Receiver2: +886289191231 AT*SMSIN=0,+886289191230,+886289191231 *SMSIN: Configured Encode: 7-Bits GSM Text Sender1: +886289191230 Sender2: +886289191231 OK AT*SMSTUN=1 OK ...

Page 122 - Other Tables; Specific Error Result Codes

A A Appendix A Result Codes, Failure Causes, and Other Tables This chapter includes information about the Result Codes, Failure Causes, and Other Tables of the OnCell G2150I. The following topics are covered in this chapter: ME Error Result Code: +CME ERROR: <error> Message Service Failure...

Page 124 - Resulting from the following commands

OnCell G2150I AT Command Set Result Codes, Failure Causes,, and Other Tables A-3 148 unspecified GPRS error All GPRS commands 149 PDP authentication failure +CGACT +CGDATA ATD*99 150 invalid mobile class +CGCLASS +CGATT Message Service Failure Result Code: +CMS ERROR: <er> <er> Meaning R...

Page 127 - Specific Failure Cause for +CEER; Cause Value

OnCell G2150I AT Command Set Result Codes, Failure Causes,, and Other Tables A-6 231 PDP deactivation cause LLC link activation failed 232 PDP deactivation cause NWK reactivation with same TI 233 PDP deactivation cause GMM abort 234 PDP deactivation cause LLC or SNDCP failure 235 PDP unsuccessful ac...

Page 129 - Unsolicited Result Codes; Verbose Result Code

OnCell G2150I AT Command Set Result Codes, Failure Causes,, and Other Tables A-8 mandatory information element is missing and/or has a content error (the two cases are undistinguishable). Cause No. 97: “Message type non-existent or not implemented” This cause indicates that the equipment sending thi...

Page 130 - Final Result Codes

OnCell G2150I AT Command Set Result Codes, Failure Causes,, and Other Tables A-9 +CLIP: <number>, <type> [,,,<alpha>] As verbose Incoming Call Presentation +CMT: <oa>… (text mode) or +CMT: [<alpha>,]… (PDU) As verbose Incoming message directly displayed +CMTI: <mem&g...

Page 131 - Intermediate Result Codes

OnCell G2150I AT Command Set Result Codes, Failure Causes,, and Other Tables A-10 Intermediate Result Codes Verbose Result Code Numeric (V0 set) Description Verbose Result Code Numeric (V0 set) Description +COLP:<number>,<type> as verbose Outgoing Call Presentation +CR: <type> as v...