Moxa EIP3000 DF1 - Manuals - manualsarea.com

Page 2 - with the terms of that agreement.; Copyright Notice; Copyright; Trademarks; MOXA is a registered trademark of Moxa Inc.; Disclaimer

MGate EIP3000 DF1 to EtherNet/IP Gateway User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright © 2009 Moxa Inc. All rights reserved. Reproduction without permission is...

Page 3 - Table of Contents; Chapter 1

Table of Contents Chapter 1 Introduction ............................................................................................... 1-1 Overview .............................................................................................................................. 1-2 Package Checklist.....

Page 4 - Chapter 6

Monitoring EtherNet/IP Activity ........................................................................................ 5-17 Open Traffic Monitor Window ................................................................................... 5-18 Filter Traffic Information .................................

Page 5 - Introduction; Overview

1 1 Chapter 1 Introduction Welcome to the MGate EIP3000 line of DF1 to EtherNet/IP gateways. All models feature easy protocol conversion from DF1 to EtherNet/IP, and RS-232/422 ports for DF1 communication. One-port and two-port models are available. This chapter is an introduction to the MGate EIP30...

Page 6 - protocol conversion between DF1 and EtherNet/IP; Protocol conversion between DF1 and EtherNet/IP; Package Checklist; Standard Accessories; MGate EIP3000 DF1 to EtherNet/IP gateway.; Optional Accessories

MGate EIP3000 Series User’s Manual Introduction Overview The MGate EIP3000 is a line of protocol gateways that provides users with y protocol conversion between DF1 and EtherNet/IP y virtual serial port for multiple DF1 and EtherNet/IP device communications y Windows utilities for easy setup and tra...

Page 7 - Product Features

MGate EIP3000 Series User’s Manual Introduction 1-3 Product Features y PCCC objects for Rockwell Automation networks supported. y 8 simultaneous EtherNet/IP clients with up to 16 simultaneous requests per client. y Serial redirector function provided. y ProCOM function provides virtual serial port f...

Page 8 - Getting Started; The following topics are covered:; Connecting Power

2 2 Chapter 2 Getting Started This chapter provides basic instructions for installing the MGate EIP3000. The following topics are covered: Connecting Power Connecting Serial Devices Connecting to a Host or the Network Installing the Software Mounting the Unit

Page 9 - Plug the power adapter into an electrical outlet.; Connecting Serial Devices

MGate EIP3000 Series User’s Manual Getting Started Connecting Power The unit can be powered using the AC adaptor or by connecting a power source to the terminal block, depending on the model. The following instructions are for the AC adaptor: 1. Plug the connector of the power adapter into the DC-IN...

Page 10 - Installing the Software; The unit can be mounted on the wall or mounted on a DIN-Rail.

MGate EIP3000 Series User’s Manual Getting Started 2-3 Installing the Software The Windows management utility is installed from the Document and Software CD. Follow the onscreen instructions after inserting the CD. Mounting the Unit The unit can be mounted on the wall or mounted on a DIN-Rail.

Page 12 - MGate EIP3000 Series User’s Manual; Panel Layout; Name

MGate EIP3000 Series User’s Manual Hardware: EIP3170, EIP3170I Panel Layout LED Indicators Name Color Function PWR1 Red Power is being supplied to the power input. PWR2 Red Power is being supplied to the power input. Red Steady on: Power is on and unit is booting up. Blinking: Indicates an IP confli...

Page 13 - Dimensions

MGate EIP3000 Series User’s Manual Hardware: EIP3170, EIP3170I Dimensions 20 mm (0.79 in) 69.5 mm (2.74 in) 25.9 mm (1.02 in) 35 mm (1.38 in) 20.6 mm (0.81 in) 29.91 mm (1.18 in) 11.5 mm (0.45 in) 124.5 mm (4.9 in) 118.5 mm (4.67 in) 89.2 mm (3.51 in) 14.5 mm (0.57 in) 29 mm (1.14 in) 14.5 mm (0.57 ...

Page 14 - Jumpers; termination resistor,; ATTENTION

MGate EIP3000 Series User’s Manual Hardware: EIP3170, EIP3170I Jumpers SW 1 The DIP switches are located beneath the DIP switch panel on the side of the unit. To add a 120 Ω termination resistor, set switch 3 to ON; set switch 3 to OFF (the default setting) to disable the termination resistor. To se...

Page 15 - Pin Assignments; Pin

MGate EIP3000 Series User’s Manual Hardware: EIP3170, EIP3170I Pin Assignments DB9 (Male) The MGate EIP3170 and EIP3170I use a DB9 (male) serial port for RS-232 connections to DF1 devices. 1 5 6 9 Pin RS-232 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS Terminal Block (RS-422) The MGate EIP3170 an...

Page 16 - Power Input, Relay Output; Mounting on the wall:

MGate EIP3000 Series User’s Manual Hardware: EIP3170, EIP3170I Power Input, Relay Output V2+ V2- V1+ V1- Shielded Ground DC Power Input 1 DC Power Input 1 Relay Output Relay Output DC Power Input 2 DC Power Input 2 DIN-Rail, Wall Mounting There are two sliders on the back of the unit for DIN-Rail an...

Page 17 - Specifications

MGate EIP3000 Series User’s Manual Hardware: EIP3170, EIP3170I 3-7 Specifications LAN Ethernet 10/100 Mbps, RJ45, Auto MDI/MDIX Protection Built-in 1.5 KV magnetic isolation Serial Interface Interface RS-232/422 No. of Ports 1 port Connector Type DB9 (male) for RS-232, terminal block for RS-422 RS-2...

Page 21 - set switch 3 on the port’s assigned DIP switch to ON set; To set the pull high/low resistors to 150 K; set switches 1 and 2 on the port’s assigned DIP switch; To set the pull high/low resistors to 1 K; set switches 1 and 2 on the port’s assigned DIP switch to

MGate EIP3000 Series User’s Manual Hardware: EIP3270, EIP3270I Jumpers SW 2 SW 1 The DIP switches are located beneath the DIP switch panel on the side of the unit. To add a 120 Ω termination resistor, set switch 3 on the port’s assigned DIP switch to ON; set switch 3 to OFF (the default setting) to ...

Page 25 - Configuring the EtherNet/IP Gateway

5 5 Chapter 5 Configuring the EtherNet/IP Gateway We discuss the following topics in this chapter: Starting MGate Manager tting ss ation nd Other Network Settings cation Parameters f Unit ctivity indow Installing the Software ¾ Change Language Se Connecting to the Unit ¾ Broadcast Search ¾ Spe...

Page 26 - Version; Next

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Installing the Software The following instructions explain how to install MGate Manager, a utility for configuring and monitoring MGate EIP3000 units over the network. 1. Insert the Document and Software CD into the CD-ROM drive....

Page 28 - Click; to start copying the software files.

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway 5. Click Next to start copying the software files. 6. A progress bar will appear. The procedure should take only a few seconds to complete. 5-4

Page 29 - You may also open MGate Manager through; Start

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway 7. A message will indicate that MGate Manager is successfully installed. You may choose to run it immediately by selecting Launch MGate Manager . 8. You may also open MGate Manager through Start Æ Programs Æ MGate Manager Æ MGate...

Page 30 - Starting MGate Manager; You may open MGate Manager from the Windows Start menu by clicking; The MGate Manager window should appear as shown; Change Language Setting; Language; to change the

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Starting MGate Manager MGate Manager is a Windows-based utility that is used to configure the MGate EIP3000. Before running MGate Manager, make sure that your PC and the MGate EIP3000 are connected to the same network. Alternativ...

Page 31 - Default Language; ” before contacting Moxa Technical Support.; Connecting to the Unit; is used to find every MGate EIP3000 on the LAN.; Search by IP; Broadcast Search; Broadcast Search; to begin searching the LAN for all MGate EIP3000 units.

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway ATTENTION Use “ Default Language ” before contacting Moxa Technical Support. With support for multiple languages, MGate Manager is more user-friendly and accessible. However, if you need assistance from Moxa Technical Support, pl...

Page 32 - Specify by IP Address; A dialog box will appear. Enter the unit’s IP address and click

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway When the search is complete, every MGate EIP3000 that is found on the LAN will appear in the window with MAC address and IP address. Simply select the one that you wish to configure. Specify by IP Address Click Specify by IP Addr...

Page 33 - to begin; Search by IP Address; Modifying the Configuration; button; Configuration; to open the configuration window.

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway If the search is successful, the unit will be listed in MGate Manager. Click the unit to begin configuration. ATTENTION If Search by IP Address fails to locate the MGate EIP3000, the IP address that you entered might be incorrect...

Page 34 - Configure IP Address and Other Network Settings

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Configure IP Address and Other Network Settings The Network tab is where the unit’s network settings are configured. You can modify the Name, Network Configuration, IP1 Address, IP2 Address (only for 2-port model) and the default...

Page 36 - Configure Serial Communication Parameters

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway ATTENTION To erase an existing password, leave both the New Password and Confirm Password text input boxes blank. The password will be erased when you click OK in the bottom right corner. Configure Serial Communication Parameters...

Page 37 - Set up Routing and ProCOM function; The definitions of the; tab determine how requests will be routed by the unit.; How to set Routing on the MGate EIP3000; Routing; page. Two kinds of routing rules can be used.; Routing

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Set up Routing and ProCOM function The definitions of the Routing tab determine how requests will be routed by the unit. How to set Routing on the MGate EIP3000 The MGate EIP3000 decides where to forward the received requests acc...

Page 38 - How to set ProCOM on the MGate EIP3000; ProCOM Mapping; to enter the mapping page. Please refer to the

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway What is ProCOM? ProCOM is Moxa’s proprietary function which provides a virtual COM port for flexible DF1 and EtherNet/IP communication. This is an intelligent function of the Fieldbus gateway that translates the data to the corre...

Page 39 - Set up Protocol

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway target DF1 device, it will forward the response to ProCOM and then the application running on your PC will receive the response. Set up Protocol You can configure the options for DF1, EtherNet/IP, and CIP protocol. Response Time-...

Page 40 - Set Up Miscellaneous; Auto; ” and “; Telnet Console; ”. The auto relay warning includes

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Set Up Miscellaneous This page defines all other options that can not be classified. Currently, this page defines “ Auto Relay Warning ”, “ Reset Button Protect ” and “ Telnet Console ”. The auto relay warning includes power fail...

Page 41 - Verifying Location of Unit; Ready; unit that you selected.; Monitoring EtherNet/IP Activity

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Verifying Location of Unit If you are managing multiple MGate units, you may wonder if you are configuring the correct unit in MGate Manager. You can select a unit in MGate Manager and click Locate to make that unit’s “ Ready ” L...

Page 42 - Open Traffic Monitor Window; Select the unit that you wish to monitor and click; Monitor; to open the Traffic Monitor window.; to begin live monitoring of the data passing through the

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Open Traffic Monitor Window Select the unit that you wish to monitor and click Monitor to open the Traffic Monitor window. In the Traffic Monitor window, click Start to begin live monitoring of the data passing through the select...

Page 43 - Filter Traffic Information; Filter info

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway To stop capturing the log, press the Stop button. Filter Traffic Information By default, all events are displayed in the traffic monitor window. MGate Manager also allows the data to be filtered so only the relevant information i...

Page 44 - Save Log to File; To save the data log to a file, click; Save; . You may retrieve a saved log by clicking; Load; Upgrading Firmware; Firmware updates for the MGate EIP3000 are located at; Upgrade; to begin the process.

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway Save Log to File To save the data log to a file, click Save . You may retrieve a saved log by clicking Load . Upgrading Firmware Firmware updates for the MGate EIP3000 are located at www.moxa.com . After you have downloaded the n...

Page 45 - to close the Upgrade; for all MGate

MGate EIP3000 Series User’s Manual Configuring the EtherNet/IP Gateway The dialog boxes will guide you through the process. You will need to browse your PC for the firmware file. Make sure that it matches your model. As the firmware is written to the unit, progress is displayed in the window. Once t...

Page 46 - We discuss the following topics in this chapter:

6 6 Chapter 6 Pin Assignments We discuss the following topics in this chapter: DB9 (Male) Terminal Block (RS-422) Power Input, Relay Output

Page 47 - GND

MGate EIP3000 Series User’s Manual Pin Assignments DB9 (Male) The MGate EIP3000 uses DB9 (male) serial ports to connect DF1 devices. Each port supports two serial interfaces: RS-232 and RS-422. 1 5 6 9 Pin RS-232 RS-422 1 DCD TxD- 2 RxD TxD+ 3 TxD RxD+ 4 DTR RxD- 5 GND GND 6 DSR --- 7 RTS --- 8 CTS ...