Moxa EDS-305 - Manuals - manualsarea.com

Page 2 - Overview; NOTE; Throughout this Hardware Installation Guide, we use; EDS = MOXA EtherDevice Switch; Package Checklist; High Performance Network Switching Technology

— 1 — Overview The MOXA EtherDevice™ Smart Switches, EDS-308/305 Series, are 8- and 5- port Ethernet Switches that provide an economical solution for your Ethernet connections, and the built-in smart alarm function helps system maintainers monitor the health of your Ethernet network. These products ...

Page 3 - Panel Layout of EDS-305 Series

— 2 — Panel Layout of EDS-305 Series EDS-305 Front Panel View 567 8 9 10 11 2 EDS-305-M-SC Front Panel View 12 13 EDS-305-S-SC Front Panel View 12 13 V1 V2 INPUTS: 24 VDC PWR2 V2+ V2- V1- V1+ 1234 5 ON DIP PORT ALARM FA U LT P W R 1 Top Panel View 1 2 3 4 1 Rear Panel View 2 15 14 14 1. Grounding sc...

Page 4 - Panel Layout of EDS-308 Series

— 3 — Panel Layout of EDS-308 Series EDS-308 Front Panel View 567 8 9 10 11 2 EDS-308-SS-SC Front Panel View 12 EDS-308-M-SC Front Panel View 12 13 567 13 V1 V2 INPUTS: 24 VDC PWR2 V2+ V2- V1- V1+ FA U LT PW R 1 123 456 78 ON DIP PORT ALARM Top Panel View 1 2 3 4 Rear Panel View 1 2 15 14 14 NOTE: T...

Page 8 - Wiring Requirements; You should also pay attention to the following items:

— 7 — Wiring Requirements WARNING Do not disconnect modules or wires unless the power supply has been switched off or the area is known to be non-hazardous. The devices may only be connected to the supply voltage shown on the type plate. The devices are designed for operation with a safety extra-low...

Page 9 - Grounding MOXA EtherDevice Switch; Wiring the Alarm Contact; Top View; : The two middle contacts of the 6-contact

— 8 — Grounding MOXA EtherDevice Switch Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. ATTENTION This product is intended to be mounted to a we...

Page 10 - Wiring the Redundant Power Inputs

— 9 — Wiring the Redundant Power Inputs The top two contacts and the bottom two contacts of the 6-contact terminal block connector on EDS’s top panel are used for EDS’s two DC inputs. Top and front views of one of the terminal block connectors are shown here. Top View Front View STEP 1 : Insert the ...

Page 11 - Communication Connections; MDI Port Pinouts; Straight-Through Cable; Connector; NIC Port; Cable Wiring

— 10 — Communication Connections EDS-308 models have 6, 7, or 8 10/100BaseT(X) Ethernet ports, and 2, 1, or 0 (zero) 100BaseFX (SC-type connector) fiber ports. EDS-305 models have 4 or 5 10/100BaseT(X) Ethernet ports, and 1 or 0 (zero) 100 BaseFX (SC-type connector) fiber ports. 10/100BaseT(X) Ether...

Page 12 - 00BaseFX Ethernet Port Connection; Redundant Power Inputs

— 11 — 100BaseFX Ethernet Port Connection The concept behind the SC port and cable is quite straightforward. Suppose you are connecting devices I and II. Contrary to electrical signals, optical signals do not require a circuit in order to transmit data. Consequently, one of the optical lines is used...

Page 13 - DIP Switch Settings; LED will never light up.; LED Indicators

— 12 — DIP Switch Settings EDS-308 Series DIP Switches EDS-305 Series DIP Switches 1 2 3 4 5 6 7 8 ON DIP 1 2 3 4 5 ON DIP ON: Enables the corresponding PORT Alarm. If the port’s link fails, the relay will form an open circuit and the fault LED will light up. Off: Disables the corresponding PORT Ala...

Page 14 - Fiber Ports; Dual Speed Functionality and Switching

— 13 — Auto MDI/MDI-X Connection The Auto MDI/MDI-X function allows users to connect MOXA EtherDevice Switch’s 10/100BaseTX ports to any kind of Ethernet device, without needing to pay attention to the type of Ethernet cable being used for the connection. This means that you can use either a straigh...

Page 15 - Technology

— 14 — automatically keeps up with new node locations. An address-aging algorithm causes the least-used addresses to be deleted in favor of newer, more frequently used addresses. To reset the address buffer, power down the unit and then power it back up. Auto-Negotiation and Speed Sensing All of MOX...