Monument Grills 41847NG - Manuals

The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. 5 Contents for Hardware Pack Tools required for assembly Philips Head Screwdriver Philips Head Screwdriver (not included).Note: The left and right sides of the ...

Figure 2 8 Assembly Instructions Figure 1 Insert Part No.47 into the bottom plate. Half screw out the screws in the bottom plate, attach Part No.35 and Part No.40 onto the relevant screw holes and screw tightly.

Figure 9 12 Figure 10 1. Insert the wire of Part No.23.2. Put Part No.2, Part No.3 onto the Main Lid. 1. Insert Part No.30, Part No.32 and Part No.33 as the figure shows.2. Insert the wire as the figure shows. 2 x

Figure 13.1 Figure 13.2 Figure 14.1 Figure 14.2 Figure 14.3 1 x A 4 x C 14 C A Fixed Part No.58 onto the right plate with one A screw. 1. Install Part No. 50 onto Part No.51 with A screws. (Figure 14.1)2. Put the C part into the relevant hole in the bottom plate. (Figure 14.2)3. Put Part No.51 into ...

Connecting LP Gas Tank to LP Grill 1. Place foot ring of 20 lb. tank into the hole in bottom panel. Make sure the tank valve is in OFF position.(Fig.20).2. Check the tank valve to ensure it has proper external mating threads to fit the hose and regulator assembly provided.3. Make sure all burner val...

LIGHTING INSTRUCTIONS FOR SIDE BURNER 1. Open side burner lid fully.2. Push and turn side burner knob to IGNITE/HI position. At the same time, press and hold electronic ignition button for 3 to 5 seconds to light burner. 3. If the side burner does not light after 5 seconds, turn knob to OFF. Turn ga...

WARNING Never lean over the grill cooking area while lighting your gas grill. Keep your face and body a safe distance (at least 18 inches) from the cooking grid surface when lighting your grill by match. If Grill Still Fails To Light 1. Check gas supply and connections for leaks. Check that all wire...

To ensure a proper working unit the following proper care and maintenance is suggested. Cleaning Cooking Grids We suggest you wash your cooking grids in a mild soap and warm water solution. You can use a washcloth or soft brush to clean your cooking grids. Cleaning Heat diffusers Periodically you sh...

BEFORE CALLING FOR SERVICE If the grill does not function properly, use the following check list before calling for service. You should inspect the burners at least once a year or immediately after any of the following conditions occur: PROBLEMS W HAT TO DO Check to see if LP tank is empty. Clean wi...

WARNING Do not leave the grill unattended. Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch cooking surfaces, grill housing. Grill Lid or any other grill parts while the grill is in operation, or until the grill has cooled down after use. Failure to...

FOOD Weight or thickness Temperature Time Special instructions and tips Vegetables NA Medium 8 to 20 minutes Slice or chop vegetables and dot with butter or margarine. W rap tightly in heavy duty foil. Grill turning occassionally. Potatoes W hole Medium 40 to 60 minutes W rap individually in heavy d...

6mm Components Orifice Size BTU Orifice Size BTU Main Burner 1.02mm 12000 1.53mm 12000 Side Burner 1.02mm 12000 1.65mm 12000 Liquid propane(LP) Natural Gas(NG) Model NO.41847NG Orifice Size Tools will be needed for gas conversion Natural Gas Conversion WARNING! FAILURE TO HEED THESE WARNINGS COULD R...

1. Turn off the main gas supply valve.2. Disconnect LP gas fuel tank (if present).3. Turn off all burner control valves.4. Remove the LP gas fuel tank (if present) from the grill cart.5. Use an adjustable wrench to remove the LP regulator from the manifold. 6.Use an adjustable wrench to install the ...

PS IG G LO B A L Q C LO W PS IG G LO B A L Q C LO W 1.Pass the NG hose to grill cart through the back panel 2.Connect the brass connector on one end of the 10 ft (3.0m) PVC flexible gas supply hose tothe Natural gas pressure regulator 3.Connect the quick connector on the other end of the 10 ft. PVC ...

Change Grill Main Burner Valve Orifices 6.Reinsert the burner and reattach using the Clamp Spring previously removed. Repeat the procedure foreach main burner 5.Replace with the Natural gas orifice. 4:Use a 6 mm socket and wrench or 6 mm nut driver toremove the brass orifice from the end of gas valv...

1:Remove all the control knobs Adjust High/Low Flame Setting Screw 2:Use a flat-blade screwdriver to turn the high flamesetscrew clockwise approximate 90º 4:Replace the control knob and turn off the burner 3:Check that burner operates at the new high flame setting. It may be necessary to adjust the ...

      WWW.MONUMENTGRILLS.COM   Product   Registration   Card   It   is   simple!   Complete   and   mail   your   Product   Registration   Card   with   the   Copy   of   the   Receipt   today!   Last   name:   ______________       First   Name:   _______________       Address:   _________________  ...