Page 2 - BEFORE YOU BEGIN; IMPORTANT; Safety Information
2 31-1000600 Rev. 0 BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep t...
Page 3 - IMPORTANT –
3 31-1000600 Rev. 0 Safety Information MISE AU REBUT ADÉQUATE DE VOTRE ÉLECTROMÉNAGER Veuillez jeter ou recycler votre électroménager conformément aux règlements fédéraux ou locaux. Communiquez avec les instances locales pour en savoir plus sur la mise au rebut ou le recyclage de votre électroménage...
Page 4 - ANTES DE COMENZAR; IMPORTANTE; PRECAUCIÓN; ADVERTENCIA; FORMA ADECUADA DE DESCARTAR SU ELECTRODOMÉSTICO
4 31-1000600 Rev. 0 Safety Information ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. • IMPORTANTE – Conserve estas instrucciones para uso del inspector local. Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el Instalador – Asegúrese de que el Comprad...
Page 5 - Contents
5 31-1000600 Rev. 0 Contents Safety 2 Design Guide Dimensions and Clearances 6 Accessories/Kits 7 Reversing the Door Swing 8 Step 1. Remove Upper Enclosure 9 Step 2. Remove Door 10 Step 3. Move Control Assembly 11 Step 4. Move Light Switch Housing 11 Step 5. Reinstall Hinge Brackets 12 Step 6. Reins...
Page 6 - Design Guide; DIMENSIONS AND CLEARANCES; Product Clearances; Overall Dimensions
6 31-1000600 Rev. 0 Design Guide DIMENSIONS AND CLEARANCES Dimensions in parentheses are in centimeters. Product Clearances These units are equipped with a 2-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. For a 90°...
Page 7 - Reversing the Door Swing (all installation types)
7 31-1000600 Rev. 0 Design Guide 7KH0RQRJUDP&ROXPQVUHIULJHUDWRUVDQGIUHH]HUVFDQEHLQVWDOOHGLQPDQ\FRQ¿JXUDWLRQVZLWKGLႇHUHQWLQVWDOODWLRQ situations. Three installation situations will be explained along with door reversal instructions and two options for door panel installation. Reversing the Door S...
Page 8 - Reversing the Door Swing; This step can be done for all installation types.
8 31-1000600 Rev. 0 Reversing the Door Swing This step can be done for all installation types.
Page 9 - Installation Instructions - Reversing the Door Swing; WARNING; Risque de
9 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 1 REMOVE UPPER ENCLOSURE Ŷ Open the front cover of the enclosure to 90°. Locate filter and filter removal tool. Filter should be as shown. Ŷ 5RWDWH¿OWHUóWXUQ counterclockwise (use ¿OWHUUHPRYDOWRROLI needed). Ŷ 3XOO¿OWHUWRZ...
Page 10 - STEP 2 REMOVE DOOR; Door Hinge Pinch
10 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 2 REMOVE DOOR Ŷ Open the door to the open position. Ŷ Have a second person support the open door. Ŷ Remove 2 T30 Torx screws securing the bottom hinge to the case. Ŷ Remove the 2 T30 Torx screws securing the top hinge to ...
Page 11 - STEP 3 MOVE CONTROL ASSEMBLY
11 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 3 MOVE CONTROL ASSEMBLY Ŷ Remove upper hinge brackets by removing the T-30 Torx screws. Ŷ Remove the Phillips head screw from the middle of the housing on the hinge side. Ŷ Insert a flat head screwdriver or putty knife be...
Page 13 - Close the compartment door.
13 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 8 REMOVE HINGES Bottom Hinge Cover Ŷ Remove bottom hinge cover. Retain cover and screws for reversing hinge covers during SS door or custom overlay panel installation. WARNING Door Hinge Pinch Point Hazard Door hinges are...
Page 14 - STEP 11 REINSTALL THE DOOR
14 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 10 PANEL BRACKETS AND HINGES Ŷ Remove panel brackets on each end of the door by removing the T30 Torx screws. Ŷ Slide same bracket on each end to other side of door and re-install brackets to door. Ŷ Install hinges to doo...
Page 15 - Instructions for Dual Integrated Installation; New construction installation with 25” deep openings
15 31-1000600 Rev. 0 Instructions for Dual Integrated Installation New construction installation with 25” deep openings
Page 16 - Design Guide - Dual Integrated Installation; DUAL INTEGRATED INSTALLATION SPACE
16 31-1000600 Rev. 0 Design Guide - Dual Integrated Installation DUAL INTEGRATED INSTALLATION SPACE Dimensions in parentheses are in centimeters. LH RH ENCLOSURE WIDTH A B C D E F G H 18 36 53 1/2 4 1/8 3 1/2 7 1/2 2 26 9 36 9 135.9 10.5 8.9 19.1 5.1 66.0 22.9 91.4 22.9 8 30 47 1/2 4 1/8 3 1/2 7 1/2...
Page 17 - Water And Electrical Locations; TOOLS AND MATERIALS REQUIRED
17 31-1000600 Rev. 0 Design Guide - Dual Integrated Installation DUAL INTEGRATED INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be located as shown. The Cutout Depth Must Be 25” Cutout is based on installation of 2 products with a left-and-right hand door swing. H...
Page 18 - Installation Instructions - Dual Integrated Installation; FLOORING; Electrical Shock; STEP 1 REMOVE PACKAGING; BEFO; KIT ZKUN PARTS SUPPLIED:; Risque d’électrocution
18 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation FLOORING For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refri...
Page 19 - ELECTRIC SHOCK HAZARD
19 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 1 REMOVE PACKAGING Ŷ Remove front access cover from unit by removing two 1/4” hex head screws. (Some models have access cover in a box on the left side of the cabinet.) Place the cover and screws to the side for futur...
Page 20 - Risque
20 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 3 PREPARING UNIT FOR INSTALLATION Ŷ Install the transformer into the case top assembly: 1. Remove cover top by removing eight #8 hex screws and keep aside for assembling back the cover top. 2. Place the transformer in...
Page 21 - STEP 4 INSTALL ANTI-TIP BRACKET; Dual install
21 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 4 INSTALL ANTI-TIP BRACKET (Cont.) Ŷ Measure and mark from the RH side of the opening per the table above depending on the size of the RH unit you are installing. Ŷ Measure and mark again from the RH side of the openi...
Page 22 - STEP 5 JOINING DUAL INSTALLED UNITS; BOTTOM BACK UNIFICATION
22 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 5 JOINING DUAL INSTALLED UNITS BOTTOM BACK UNIFICATION Ŷ Loosen the two bottom screws of rear access covers of both units and remove the top screws. Ŷ Hang the unification bracket to the bottom screws and reassemble t...
Page 23 - STEP 6 CONNECTING WATER; SmartConnect
23 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 6 CONNECTING WATER SUPPLY Ŷ Locate and bring the tubing to the front of the cabinet. Ŷ Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off the wa...
Page 24 - Electrical Shock Hazard.; Trisque de
24 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 7 INSERTING/SECURING INTO CABINET SURROUND Ŷ Plug both units into the outlet in the wall. Ŷ Find the installation string that is attached to the door of the unit; this is to be used as you are pushing the unit back in...
Page 25 - STEP 8 LEVEL UNIT
25 31-1000600 Rev. 0 STEP 7 INSERTING/SECURING INTO CABINET SURROUND (Cont.) Ŷ Replace the waterline strain relief screw. Ŷ Store the excess string, and water tubing under the unit. Installation Instructions - Dual Integrated Installation WARNING Electrical Shock Hazard. Replace waterline strain rel...
Page 26 - FOR FLUSH INSTALLATION:
26 31-1000600 Rev. 0 Ŷ Locate blue arrow on ¿OWHU5RWDWH¿OWHUWR align arrow as shown. Ŷ ,QVHUW¿OWHULQWRSRVLWLRQ DQGURWDWHóWXUQFORFNZLVHXVH¿OWHU removal tool if needed). Ŷ 5HWXUQ¿OWHUUHPRYDOWRROWR mounting hook. Ŷ Close the compartment door. Ŷ Verify the two 1/4” hex head screws are assembled to handl...
Page 27 - STEP 10 TOE KICK INSTALLATION
27 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.) Ŷ Install front mullion and access cover trims between the 2 units. Open the doors and the flexible dart in the area between units. Ŷ Top dart of the mullion must align with b...
Page 28 - ON; STEP 12 START ICEMAKER; OFF; CAUTION; ATTENTION
28 31-1000600 Rev. 0 STEP 12 START ICEMAKER (freezer models) When the freezer has been connected to the water supply, set the power switch to ON . Throw away the first full bucket of ice to allow the water line to clear. Be sure nothing interferes with the sweep of the feeler arm. When the bin fills...
Page 29 - STEP 13 INSTALL AUTOFILL PITCHER ASSEMBLY
29 31-1000600 Rev. 0 Installation Instructions - Dual Integrated Installation STEP 13 INSTALL AUTOFILL PITCHER ASSEMBLY (Some Refrigerator Models) Ŷ Locate the AutoFill pitcher cover on the left side of the refrigerator’s interior. Remove T20 Torx screw holding the cover in place towards the rear of...
Page 30 - Instructions for Retro-Fit Installation; Existing construction installation with 24” deep openings
30 31-1000600 Rev. 0 Instructions for Retro-Fit Installation Existing construction installation with 24” deep openings that are 35-1/2”, 36”, 41-1/2”, 47-1/2” or 71-1/2” wide
Page 31 - For 24” Deep Cutouts; DUAL RETRO-FIT INSTALLATION SPACE; Design Guide - Dual Retro-Fit Installation
31 31-1000600 Rev. 0 Water And Electrical Locations Electrical and water supply must be located as shown. For 24” Deep Cutouts Trim Retro kits are required for a 35.5” (ZKR36R), 36”(ZKR36R), 41.5”(ZKR42N), 47.5”(ZKR48N) or 71.5”(ZKR72R) wide opening. Heater Unification Kit ZKUN required Product Clea...
Page 32 - Installation Instructions - Dual Retro-Fit Installation
32 31-1000600 Rev. 0 Installation Instructions - Dual Retro-Fit Installation FLOORING For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrig...
Page 33 - EFORE
33 31-1000600 Rev. 0 Installation Instructions - Dual Retro-Fit Installation STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. This appliance is top heavy. Use extreme caution with moving to prevent tipping over which could result in death or serious injury. Ŷ Remove outer carton and external packing...
Page 34 - STEP 2 INSTALL WATER LINE
34 31-1000600 Rev. 0 Installation Instructions - Dual Retro-Fit Installation STEP 2 INSTALL WATER LINE (Cont.) NOTE: Saddle type shut-off valves are included in many water supply kits. Before purchasing, make sure a saddle type valve complies with your local plumbing codes. NOTE: Commonwealth of Mas...
Page 38 - CHANGE POWER CORD; Install new longer power cord:; CASE TRIM INSTALLATION
38 31-1000600 Rev. 0 Installation Instructions - Dual Retro-Fit Installation STEP 5 JOINING DUAL INSTALLED UNITS (Cont.) CHANGE POWER CORD Longer power cords are required for retro fit installation. Power cords are included in 42” ZKR42N and 48” ZKR48N. Replace power cords on both units. Both units ...
Page 41 - STEP 7 INSERTING/SECURING INTO
41 31-1000600 Rev. 0 Installation Instructions - Dual Retro-Fit Installation STEP 7 INSERTING/SECURING INTO CABINET SURROUND Ŷ Slowly walk both units into opening making sure not to touch the cabinetry on the sides and top to prevent damage. The back side of the top and side retro trims should be to...
Page 44 - STEP 12 START ICEMAKER
44 31-1000600 Rev. 0 Installation Instructions - Dual Retro-Fit Installation STEP 11 INTERNAL UNIT PREPARATION Ŷ Remove all tape, cardboard, and foam from each unit (foam shipping supports may be located behind the left and right sides of each of the glass pan fronts on Refrigerator models). Ŷ Remov...
Page 46 - Instructions for Single Integrated Installation
46 31-1000600 Rev. 0 Instructions for Single Integrated Installation New construction installation with 25” deep openings
Page 47 - Design Guide - Single Integrated Installation; SINGLE INTEGRATED INSTALLATION SPACE; The Cutout Depth Must Be 25”.
47 31-1000600 Rev. 0 Design Guide - Single Integrated Installation SINGLE INTEGRATED INSTALLATION SPACE Dimensions in parentheses are in centimeters. Water And Electrical Locations Electrical and water supply must be located as shown. The Cutout Depth Must Be 25”. Additional Specifications Ŷ A 115 v...
Page 48 - Installation Instructions - Single Integrated Installation
48 31-1000600 Rev. 0 Installation Instructions - Single Integrated Installation FLOORING For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded ref...
Page 49 - BEFORE
49 31-1000600 Rev. 0 Installation Instructions - Single Integrated Installation KIT ZKUN PARTS SUPPLIED: Adhesive Heater Transformer Front Mullion Trim Bracket Top Unification Bracket Bottom Front Unification Bracket 3 1/4” Hex Head 8-18 5/8” Long Screws 5 1/4” Hex Head 8-32 5/8” Long Screws 5 3/8” ...
Page 54 - STEP 7 LEVEL UNIT
54 31-1000600 Rev. 0 Installation Instructions - Single Integrated Installation STEP 7 LEVEL UNIT All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit. Ŷ To level the back of the unit, tu...
Page 55 - STEP 9 TOE KICK INSTALLATION
55 31-1000600 Rev. 0 Installation Instructions - Single Integrated Installation Ŷ Make sure lights are on inside the unit. If they are not on, check to make sure the master switch is on by removing the front enclosure which is secured with six 1/4” Hex screws. Ŷ Switch on the master switch if not on...
Page 56 - STEP 11 START ICEMAKER (freezer models)
56 31-1000600 Rev. 0 Installation Instructions - Single Integrated Installation STEP 11 START ICEMAKER (freezer models) A newly-installed freezer may take 12–24 hours to begin making ice. The icemaker will produce seven cubes per cycle—approximately 15 cycles in a 24-hour period, depending on freeze...
Page 57 - STEP 12 INSTALL AUTOFILL PITCHER ASSEMBLY
57 31-1000600 Rev. 0 Installation Instructions - Single Integrated Installation STEP 12 INSTALL AUTOFILL PITCHER ASSEMBLY (Some Refrigerator Models) Ŷ Locate the AutoFill pitcher cover on the left side of the refrigerator’s interior. Remove the one T20 Torx screw holding the cover in place towards t...
Page 58 - Stainless Steel Door Panel Installation
58 31-1000600 Rev. 0 Stainless Steel Door Panel Installation This step can be done for all installation types.
Page 59 - Installation Instructions - Stainless Door Panel; Door Trim Pinch; STEP 1 INSTALL STAINLESS PANEL; Risque de pincement
59 31-1000600 Rev. 0 Installation Instructions - Stainless Door Panel Stainless Steel Door Panel Kits are available with either Euro handles or Pro handles. Stainless steel panel is fully assembled with brackets and handle already installed as a LH or RH swing door. LH door kits can be modified to f...
Page 60 - hinge side
60 31-1000600 Rev. 0 Installation Instructions - Stainless Door Panel STEP 2 ADJUST STAINLESS PANEL (Cont.) Ŷ Follow the next steps for set screw installation. Ŷ For flush mounting, inspect the gap between the panel and cabinetry at the handle side. ¿ If the vertical gap between the cabinetry is sma...
Page 61 - STEP 4 INSTALL HINGE COVERS; STEP 3 IF DOORS WERE REVERSED COMPLETE THE
61 31-1000600 Rev. 0 Installation Instructions - Stainless Door Panel STEP 4 INSTALL HINGE COVERS Ŷ Replace the top and bottom hinge covers using 4-T30 screws per cover. Ŷ Using one T10 screw, secure the cover top to L-Bracket. STEP 3 IF DOORS WERE REVERSED COMPLETE THE FOLLOWING STEPS Ŷ Top cover a...
Page 62 - STEP 5 INSTALL DOOR TRIMS
62 31-1000600 Rev. 0 Installation Instructions - Stainless Door Panel STEP 5 INSTALL DOOR TRIMS There are 2 door trims to install. One for the handle side and one for the hinge side. The long trim is for the handle side and the shorter trim is for the hinge side. Install the handle side trim first. ...
Page 63 - Custom Overlay Door Panel Installation
63 31-1000600 Rev. 0 Custom Overlay Door Panel Installation This step can be done for all installation types.
Page 64 - /4” CUSTOM DECORATIVE PANEL DIMENSIONS; Design Guide - Custom Overlay Door Panel; CUSTOM HANDLE DESIGN GUIDE; Door Trim Pinch Point
64 31-1000600 Rev. 0 3/4” CUSTOM DECORATIVE PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed to give a flush appearance with surrounding cabinets. The overlay panel must be 3/4” (1.91cm) thick. Panel attaches to included brackets to provide mounting to the appliance doo...
Page 65 - Installation Instructions - Custom Overlay Door Panel; STEP 1 OVERLAY PANEL PREP
65 31-1000600 Rev. 0 Installation Instructions - Custom Overlay Door Panel STEP 1 OVERLAY PANEL PREP Ŷ Verify overall panel dimensions match supplied recommendations based on model and inspect for any initial damage. Ŷ Lay the template on the BACK of the panel, making sure to align the top edge (bla...
Page 66 - STEP 2 INSTALL OVERLAY PANEL; STEP 3 ADJUST OVERLAY PANEL
66 31-1000600 Rev. 0 STEP 2 INSTALL OVERLAY PANEL Ŷ Remove bottom hinge cover and retain the 4 T30 Torx screws for later installation. Ŷ Open door to 90°. Slide the panel onto the door with the panel brackets interlocking on top and bottom with the door brackets (make sure not to slide the panel int...
Page 67 - STEP 4 IF DOORS WERE REVERSED COMPLETE THE
67 31-1000600 Rev. 0 Installation Instructions - Custom Overlay Door Panel STEP 3 ADJUST OVERLAY PANEL (Cont.) After the panel has been adjusted to the desired position, secure the panel by first driving and tightening the vertical screws at the bottom of the door brackets and then drive and tighten...
Page 68 - STEP 6 INSTALL DOOR TRIMS
68 31-1000600 Rev. 0 Installation Instructions - Custom Overlay Door Panel STEP 6 INSTALL DOOR TRIMS There are 2 door trims to install. One for the handle side and one for the hinge side. The long trim is for the handle side and the shorter trim is for the hinge side. Install the handle side trim fi...
Page 70 - Notes
