Monessen 3000 SERIES - Manuals

Monessen 3000 SERIES – Manual in PDF format online.

Manuals:

Manual

Manual Monessen 3000 SERIES

Summary

Page 7 - Figure 1: Fireplace Dimensions

P P R R E E - - I I N N S S T T A A L L L L A A T T I I O O N N I I N N F F O O R R M M A A T T I I O O N N 5 Figure 1: Fireplace Dimensions 2 Figure 2: Fireplace Locations and Minimum Clearances Requirements

Page 8 - less than 2” on both the left and right side.

P P R R E E - - I I N N S S T T A A L L L L A A T T I I O O N N I I N N F F O O R R M M A A T T I I O O N N 6 2” Min 2” Min 31” Min Figure 3: Wall & Ceiling Minimum Clearances Wall and Ceiling Clearance Requirements: Ensure that minimum clearance shown in Figures 3 is maintained. Left and right ...

Page 9 - install; Minimum Vent Clearances to Combustible Materials:

P P R R E E - - I I N N S S T T A A L L L L A A T T I I O O N N I I N N F F O O R R M M A A T T I I O O N N 7 Mantel Clearances: A hood/canopy comes with every appliance. If a combustible mantel is installed, it must meet the clearance requirements detailed in Figure 4. Combustible wall or drywall t...

Page 11 - F minimum adhesive may be used to attach facing materials; Figure 7: Finishing Material

P P R R E E - - I I N N S S T T A A L L L L A A T T I I O O N N I I N N F F O O R R M M A A T T I I O O N N 9 Finishing Material: NOTE Any remote wiring (i.e. remote control, wall switch, and optional fan) must be done prior to final finishing to avoid costly reconstruction. WARNING Never obstruct o...

Page 14 - foot Min; NOTE

V V E E N N T T I I N N S S T T A A L L L L A A T T I I O O N N 12 Horizontal Venting with Three (3) Elbows: Figure 11: Horizontal Venting with Three (3) Elbows INSTALLING VENT COMPONENTS Before You Start: Plan your installation. Set unit in place and survey how best to vent the unit. Select the app...

Page 16 - Figure 13: Wall Firestop Location

V V E E N N T T I I N N S S T T A A L L L L A A T T I I O O N N 14 For Ceiling • For ceiling firestops, position a plumb bob over the center of the vertical pipe; to spot a hole through which the pipe will penetrate. • Drill a hole through this centerpoint and check the floor for obstructions (i.e. ...

Page 17 - For Vertical Termination; Figure 15: Minimum Vent Height for Various Roof Pitches; To locate and install vertical termination

V V E E N N T T I I N N S S T T A A L L L L A A T T I I O O N N 15 Vent Termination: For Vertical Termination Figure 15: Minimum Vent Height for Various Roof Pitches WARNING Major building codes specify a minimum vent height above the rooftop depending on the pitch of the roof. Refer to the above fi...

Page 18 - For Horizontal Termination; Figure 16: Horizontal Vent Termination Location

V V E E N N T T I I N N S S T T A A L L L L A A T T I I O O N N 16 For Horizontal Termination Figure 16: Horizontal Vent Termination Location # A=12 inches Clearance above the grade, a veranda, porch, deck, or balcony # B=12 inches Clearance to window or door that may be opened. C=12 inches Clearanc...

Page 19 - To locate and install horizontal high wind termination cap (P/N 985)

V V E E N N T T I I N N S S T T A A L L L L A A T T I I O O N N 17 WARNING Always maintain minimum clearances around vent systems. The minimum clearances to combustibles for horizontal vent pipe are 3 inches at the top and 1 inch at the sides and bottom of the vent system. For wall firestops, a 1-in...

Page 20 - Figure 18 Horizontal Termination Cap on a Vinyl Siding Wall; A wall firestop; MUST BE; Vinyl Siding Wall

V V E E N N T T I I N N S S T T A A L L L L A A T T I I O O N N 18 Figure 18 Horizontal Termination Cap on a Vinyl Siding Wall To locate and install horizontal termination cap (P/N HTC) • A wall firestop MUST BE installed if the vent passes through a wall or ceiling. Cut a 10-inch X 10-inch hole thr...

Page 24 - Optional Fan/Blower Systems; Figure 22: Blower Wiring Diagram

G G A A S S L L I I N N E E A A N N D D E E L L E E C C T T R R I I C C A A L L I I N N S S T T A A L L L L A A T T I I O O N N 22 Optional Fan/Blower Systems The junction box for the fan/blower systems has been factory installed. This system requires that 110-120 VAC to be wired to the factory inst...

Page 26 - Electronic Pilot Ignition Wiring:; WARNING

G G A A S S L L I I N N E E A A N N D D E E L L E E C C T T R R I I C C A A L L I I N N S S T T A A L L L L A A T T I I O O N N 24 Electronic Pilot Ignition Wiring: WARNING Do not connect 110-120 VAC to the Remote Wall Switch. The appliance will malfunction or destroyed. Figure 24: Wiring Diagram fo...

Page 31 - Figure 29: Log Placement

F F I I N N A A L L I I N N S S T T A A L L L L A A T T I I O O N N 29 Log Placement: This fireplace is supplied with a set of four (4) ceramic fiber logs. Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your...

Page 32 - Read the; You may notice the following:

O O P P E E R R A A T T I I N N G G I I N N S S T T R R U U C C T T I I O O N N S S 30 OPERATING INSTRUCTIONS Before Lighting the Fireplace: • Read the IMPORTANT SAFETY INFORMATION section at the beginning of this homeowner manual. • Before lighting, verify the fireplace for possible gas leaks. • Be...

Page 40 - Defective valve

T T R R O O U U B B L L E E S S H H O O O O T T I I N N G G 38 TROUBLESHOOTING Standing Pilot Ignition: SYMPTOM POSSIBLE CAUSE ACTION 1. Spark ignitor will not light pilot after repeated triggering of piezo. A. Wire disconnected. Open door and check to make sure wire is connected to ignitor. B. Defe...

Page 44 - LIMITED LIFETIME WARRANTY POLICY; Lifetime Warranty

P/N 37D0634, Rev 4 Sept 2000 LIMITED LIFETIME WARRANTY POLICY Lifetime Warranty The following components are warranted for life to the original owner, subject to proof of purchase: Firebox, Combustion Chamber, Heat Exchanger, Grate and Stainless Steel Burners. Five Year Warranty The following compon...