Mitsubishi PUHZ-SW120VHA-BS.UK- Manuals

5 2-3. PRECAUTIONS WHEN REUSING EXISTING R22 REFRIGERANT PIPES Flowchart Perform the airtight test, vacuum air purging, additional refrigerant charging (if necessary), and gas leak check. • Refer to the fl owchart below to determine if the existing pipes can be used and if it is necessary to use a fi ...

6 Cautions for refrigerant piping work New refrigerant R410A is adopted for replacement inverter series. Although the refrigerant piping work for R410A is same as for R22, exclusive tools are necessary so as not to mix with different kind of refrigerant. Furthermore as the working pressure of R410A ...

7 3 FEATURES PUHZ-SW75VHA.UKPUHZ-SW75VHA-BS.UK CHARGELESS SYSTEMPRE-CHARGED REFRIGERANT IS SUPPLIED FOR PIPING LENGTH AT SHIPMENT.(Max. 10m (PUHZ-SW75-120)) The refrigerant circuit with LEV (Linear Expansion Valve) and Accumulator always control the optimal refrigerant level regardlessof the length ...

8 4 SPECIFICATIONS <Reference data> Plate heat exchanger (ACH70-40 plates) Nominal water fl ow L/min 22.9 Heating(A7/W35) Capacity kW 8.00 COP 4.40 Power input kW 1.82 Heating(A7/W45) Capacity kW 8.00 COP 3.40 Power input kW 2.35 Heating(A2/W35) Capacity kW 7.50 COP 3.40 Power input kW 2.20 Hea...

11 5 DATA 5-1. REFILLING REFRIGERANT CHARGE (R410A : kg) 5-2. COMPRESSOR TECHNICAL DATA Service Ref. Piping length (one way) Initial charged 10m 20m 30m 40m 50m 60m 75m PUHZ-SW75VHA.UKPUHZ-SW75VHA-BS.UK 3.2 3.6 4.0 4.6 — — — 3.2 PUHZ-SW100VHA.UKPUHZ-SW100VHA-BS.UKPUHZ-SW100YHA.UKPUHZ-SW100YHA-BS.UK ...

13 6 OUTLINES AND DIMENSIONS Unit : mm Air Intake Rear Air Intake Handle for moving Handle for moving 322 950 473 943 23 *1 447 *1 431 673 2 1 Handle for moving Handle for moving Service panel Earth terminal Left···Power supply wiring Right···Indoor/Outdoor wiring Terminal Connections Rear piping co...

15 7 WIRING DIAGRAM 1 2 3 4 5 6 7 8 OFF ON 75V MODEL SW6 * 1 MODEL SELECT The black square ( ) indicates a switch position. SW5-6 * 2 OFF ON 1 2 3 4 5 6 * 2 SW5 -1 to 5 : Function Switch SYMBOL NAME SYMBOL NAME SYMBOL NAME TB1MCMF121S463H63HSTH3TH4TH6TH7TH8TH34LEV-A, LEV-BACLCY1, CY2 Terminal Block ...

18 8 WIRING SPECIFICATIONS FIELD ELECTRICAL WIRING (power wiring specifications) Outdoor unit model SW75V SW100V SW120V SW100, 120Y Outdoor unit power supply ~/N (single), 50 Hz, 230 V ~/N (single), 50 Hz, 230 V ~/N (single), 50 Hz, 230 V 3N~ (3 ph 4-wires), 50 Hz, 400 V Outdoor unit input capacity ...

19 9 REFRIGERANT SYSTEM DIAGRAM unit : mm(inch) Distributor Thermistor TH7(Ambient) Heat exchanger Refrigerant LIQUID pipe connection : 9.52(3/8) Stop valve(with service port) Strainer#100 Powerreceiver Linearexpansion valve B Linear expansion valve A Strainer#100 Thermistor TH6(2-phase pipe) Thermi...

20 9-2. Unit replacement operation When reusing the existing pipes that carried R22 refrigerant for the SW75/100/120 models, replacement operation must be performed before performing a test run. 1 If new pipes are used, these procedures are not necessary. 2 If existing pipes that carried R22 refrige...

21 10 TROUBLESHOOTING 10-1. TROUBLESHOOTING <Error code display by self-diagnosis and actions to be taken for service (summary)> Present and past error codes are logged and displayed on the control board of outdoor unit. Actions to be taken for service, which depends on whether or not the trou...

22 10-3. SELF-DIAGNOSIS ACTION TABLE <Abnormalities detected when the power is turned on> Note: Refer to indoor unit section for code P and code E. Error Code Abnormal point and detection method Case Judgment and action None — 1 No voltage is supplied to terminal block (TB1) of outdoor unit. a...

24 Error Code Abnormal point and detection method Judgment and action U1 High pressure (High-pressure switch 63H operated) Abnormal if high-pressure switch 63H operated ( ) during compressor operation. 4.15 MPa 63H: High-pressure switch 1 Short cycle of indoor unit 2 Clogged filter of indoor unit 3 ...

34 AC 198V to AC 264V? AC 198V to AC 264V? AC 198V to AC 264V? DC 12V to DC 16V? DC 12V to DC 16V? NO YES NO YES NO YES YES NO YES NO Check the voltage between S1 and S2 on the terminal block (TB4) of the indoor unit which is used to connect the indoor unit and the outdoor unit. Check the voltage am...