Mitsubishi PKA-RP-HAL- Manuals

5 1 2 3 2. Parts Names ■ Wireless Remote-Controller ■ When using the wireless remote controller, point it towards the receiver on the indoor unit. ■ If the remote controller is operated within approximately 2 minutes after power is supplied to the indoor unit, the indoor unit may beep twice as the u...

7 5. Operation 5.2. Mode select ■ Press the operation mode ( ) button 2 and select the opera- tion mode 2 . Cooling mode Drying modeFan mode Heating mode <Only heat pump type> Automatic (cooling/heating) mode <Only heat pump type>Ventilation mode Only indicated on the following condition...

8 5. Operation Note: ● Available directions depend on the type of unit connected. ● In the following cases, the actual air direction will differ from the direction indicated on the remote controller display. 1. While the display is showing “STAND BY” or “DEFROST”. 2. Immediately after starting heat ...

9 C C TIME SUN WEEKLY 10 C TIMER SUN ONOFF WEEKLY 8 9 1 Timer Settings 1. Be sure that the weekly timer indicator is visible on the screen (at 1 ). 2. Press the Timer Menu button 2 so that “Monitor” is indicated on the screen (at 8 ). 3. Press the Timer On/Off (Set Day) button 9 as necessary to sele...

10 <How to Set the Simple Timer> 6. Timer Action (On or Off)* “— —” is displayed if there is no setting. Timer Setting ON HrAFTER SIMPLE 4. With “ON” or “OFF” showing at 3 : Press the appropriate Set Time but- ton as necessary to set the hours to ON (if “ON” is displayed) or the hours to OFF (...

11 <Checking the Current Auto Off Timer Setting> AFTER TIMER OFF AUTO OFF Timer Setting ˚ C ˚ C AFTER OFF AUTO OFF AUTO OFF 1. Be sure that the “Auto Off” is visible on the screen (at 1 ). 2. Hold down the Timer Menu button 2 for 3 seconds so that “Monitor” is indicated on the screen (at 4 ). ...

13 8. Function Selection Function selection of remote controller The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting whenneeded. Item 1 Item 2 Item 3 (Setting content) 1. Change Language (“CHANGE LAN-GUAGE”) ...

16 8. Function Selection [Dot display table] Waiting for start-up Operation mode Cool Dry Heat Auto Auto(Cool) Auto(Heat) Fan Ventilation Stand by(Hot adjust)Defrost Set temperature Fan speed Not use button Check (Error) Test run Self check Unit function selection Setting of ventilation CHANGE LANGU...

17 E.O. SW 10. Care and Cleaning ON/OFF TEMP. C C FILTER Note:• Details of emergency mode are as shown below. Operation mode COOL HEAT Set temperature 24°C 24°C Fan speed High High Airfl ow direction Horizontal Downward 4 (5) ■ Indicates that the fi lter needs cleaning. Clean the fi lter. ■ When res...

18 10. Care and Cleaning / 0 1 PSA-RP·GA 1 Open the intake grille. 2 Hold the knob on the fi lter then pull the fi lter up in the direction of an arrow. To replace the fi lter after cleaning, be sure to insert the fi lter far enough until it fi ts into the stopper. A Filter B Intake Grille C Knob D ...

19 11. Trouble Shooting Having trouble? Here is the solution. (Unit is operating normally.) Air conditioner does not heat or cool well. ■ Clean the fi lter. (Airfl ow is reduced when the fi lter is dirty or clogged.) ■ Check the temperature adjustment and adjust the set temperature. ■ Make sure that...

HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN BG79U612H03 Printed in Japan Please be sure to put the contact address/telephone number on this manual before handing it to the customer. BG79U612H03.indd   22 BG79U612H03.indd   22 2008/12/11   9:03:08 2008/12/11   9:03:...