Mitsubishi P08- Manuals

5 ● Wired remote controller ● ● ˚F˚C ˚F˚C ERROR CODE AFTER TIMER TIME SUN MON TUE WED THU FRI SAT ON OFF Hr AFTER FILTER FUNCTION ONLY1Hr. WEEKLY SIMPLE AUTO OFF Note: “PLEASE WAIT” messageThis message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the uni...

6 4 SPECIFICATIONS 4-1. SPECIFICATIONS Note 1. Rating conditionsCooling : Indoor : D.B. 80 _ F W.B. 67 _ F outdoor : D.B. 95 _ F W.B. 75 _ F Heating : Indoor : D.B. 70 _ F outdoor : D.B. 47 _ F W.B. 43 _ F Note 2. The number indicated in < > is for the grille. W 3. Air flow and the noise level...

7 UNIT 5ft MICROPHONE CEILING 4-2. NOISE CRITERION CURVES 90 80 70 60 50 40 30 20 10 63 125 250 500 1000 2000 4000 8000 APPROXIMATETERESHOLD OFHEARING FORCONTINUOUSNOISE NC-60 NC-50 NC-40 NC-30 NC-20 NC-70 OCT A VE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 µ bar) BAND CENTER FREQUENCIES, Hz High ...

9 5 4-WAY AIR FLOW SYSTEM 5-3. OPERATION IN CONJUNCTION WITH DUCT FAN (BOOSTERFAN) • Whenever the indoor unit is operating, the duct fun also operates. (1)Connect the optional multiple remote controller adapter(PAC-SA88HA-E) to the connectorCN51 on the indoor controller board. (2)Drive the relay aft...

10 5-4. FIXING HORIZONTAL VANE Horizontal vane of each air outlet can be fixed according to the environment where it is installed. Setting procedure1) Turn off a main power supply (Turn off a breaker).2) Disconnect the vane motor connector of the direction of the arrow with pressing the unlocking bu...

11 OUTLINES AND DIMENSIONS 6 PLFY-P08NCMU-E.TH PLFY-P12NCMU-E.TH PLFY-P15NCMU-E.TH Unit : inch(mm) PLFY-P08NCMU-E 1 .TH PLFY-P12NCMU-E 1 .TH PLFY-P15NCMU-E 1 .TH Detail drawing of fresh air intake Ceiling surface Cut out hole [ 2-7/8( [ 73.4) Burring hole 3- [ 1/8( [ 2.8) [ 3-15/16( [ 100) 4-21/32(1...

12 WIRING DIAGRAM 7 PLFY-P08NCMU-E.TH PLFY-P12NCMU-E.TH PLFY-P15NCMU-E.TH PLFY-P08NCMU-E 1 .TH PLFY-P12NCMU-E 1 .TH PLFY-P15NCMU-E 1 .TH DP WHT (DRAIN) WHT FAN (FAN) See fig: W 1 MODELS P08 P12 P15 <fig: W 1> ON OFF 1 2 3 4 5 6 ON OFF 1 2 3 4 5 6 ON OFF 1 2 3 4 5 6 SW2 Power supply for MA-Remo...

13 REFRIGERANT SYSTEM DIAGRAM 8 Strainer (#50mesh) Strainer (#100 mesh) Strainer1 (#50 mesh)Strainer2 (#100 mesh) Heat exchanger Room temperature thermistor TH21 Gas pipe thermistor TH23 Liquid pipe thermistor TH22 Linear expansion valve Gas pipe Liquid pipe Flare connection Gas pipe Liquid pipe 1/2...

14 MICROPROCESSOR CONTROL 9 PAR-21MAA ON/OFF FILTER CHECK OPERATION CLEAR TEST TEMP. MENU BACK DAY MONITOR/SET CLOCK ON/OFF ˚F˚C ˚F˚C ERROR CODE AFTER TIMER TIME SUN MON TUE WED THU FRI SAT ON OFF Hr AFTER FILTER FUNCTION ONLY1Hr. WEEKLY SIMPLE AUTO OFF INDOOR UNIT CONTROL9-1. COOL OPERATION Control...

15 → 3 2 1 → Control modes Control details 3-1. Drain pump control • Always drain pump ON during the COOL and DRY mode operation. (Regardless of the thermo ON/ OFF) • When the operation mode has changed from the COOL or DRY to the others (including Stop), OFF the control after the drain pump ON for ...

21 10 TROUBLESHOOTING 10-1. HOW TO CHECK THE PARTSPLFY-P08NCMU-E.TH PLFY-P12NCMU-E.TH PLFY-P15NCMU-E.TH PLFY-P08NCMU-E 1 .TH PLFY-P12NCMU-E 1 .TH PLFY-P15NCMU-E 1 .TH Parts name Check points Disconnect the connector then measure the resistance with a tester.(At the ambient temperature 50 - F~86 - F)...

22 4 [ 4 3 6 2 5 [ 3 2 [ 2 1 [ 1 [ 4 [ 3 [ 2 [ 1 Controller board Drive circuit Relay connector Connector(CN60) DC12V Brown Red Blue Orange Yellow White 5 1 3 4 6 M 4 6 2 3 5 1 Blue Brown Yellow Orange Red White Linear expansion valve <Thermistor characteristic graph> Room temperature thermist...

23 Output (Phase) Output { 1 1 ON { 2 ON { 3 OFF { 4 OFF 2 OFF ON ON OFF 3 OFF OFF ON ON 4 ON OFF OFF ON <Output pulse signal and the valve operation> 2 2 Linear expansion valve operation 3 3 Troubleshooting D A E B C Open Extra tightening (80~100pulse) Pulse number 2000 pulseOpening a valveal...

28 DISASSEMBLY PROCEDURE 11 OPERATING PROCEDURE PHOTOS&ILLUSTRATIONS 1. Removing the air intake grille (1) Slide the knob of air intake grille to the direction of the arrow 1 to open the air intake grille. (2) Remove the string hook from the panel to prevent the grille from dropping. (3) Slide t...

29 OPERATING PROCEDURE PHOTOS&ILLUSTRATIONS 7. Removing the pipe temperature detection/liquid (TH22) and pipe temperature detection/gas (TH23)(1) Remove the panel. (Refer to 3)(2) Remove the drain pan. (Refer to 6)(3) Disconnect the liquid or gas from the holder.(4) Remove the 3 screws fixed to ...

30 OPERATING PROCEDURE PHOTOS&ILLUSTRATIONS 10. Removing the heat exchanger (1) Remove the panel. (Refer to 3 )(2) Remove the drain pan. (Refer to 6)(3) Remove the nut and the washer from the turbo fan, and remove the turbo fan. (4) Remove the 2 screws fixed to the control box cover, and remove ...