Mitsubishi MS-GD10ND- Manuals

5 [ 9.52-0.43m 244 242 5 er o m r o 7 90 110 03 149 606 87 2 60 815 783 Air out Installation plate Insulation [ 28 Drain hose [ 16 (Connected part O.D) Liquid line [ 6.35-0.5m Gas line [ 9.52-0.43m Insulation [ 37 O.D [ 21 I.D { Wireless remote controller 81.5 81.5 14 5. 2 24 17 2 5. 13 2 5. 4 81.5 ...

6 MS-GD08ND- C1 MS-GD12ND- C1 WIRING DIAGRAM 5 INDOOR UNIT MS-GD10ND- C1

7 REFRIGERANT SYSTEM DIAGRAM 6 MS-GD08ND- C1 MS-GD10ND- C1 INDOOR UNIT Roomtemperaturethermistor Indoor heat exchanger RT11 Indoor coilthermistorRT12 Refrigerant pipe(Option) { 6.35 (with heat insulator) Flaredconnection Flaredconnection Refrigerant pipe(Option) { 12.7 (with heat insulator) Refriger...

8 Table 1 How to set the remote controller exclusively for particular indoor unit After you turn the breaker ON, the first remote controller that sends the signal to the indoor unit will be regarded as the remote controller for the indoor unit. The indoor unit will only accepts the signal from the r...

9 When the indoor unit is controlled with the remote controller, the operation mode, set temperature, and the fan speed are memorized by the indoor electronic control P.C.board. The “AUTO RESTART FUNCTION” sets to work the moment power has restored after power failure. Then, the unit will restart au...

10 8-1. Cautions on troubleshooting 1. Before troubleshooting, check the following: 1) Check the power supply voltage. 2) Check the indoor/outdoor connecting wire for mis-wiring. 2. Take care the following during servicing. 1) Before servicing the air conditioner, be sure to turn off the main unit f...

15 Yes B Check of remote controller and receiver P.C. board w Check if the remote controller is exclusive for this air conditioner. Replace the batteries. (Refer to 8-1.4.) Turn on a radio to AM and press switch on the remote controller. Is noise heard from radio? Are there any fluorescent lights of...

16 C Check of indoor electronic control P.C. board The unit doesn’t operate with the remote controller. Also, the OPERATION INDICATOR lamp doesn’t light up by pressing the EMERGENCY OPERATION switch. CN201 L N 1 3 Terminal block Check both “parts side” and “patternside” of the indoor electronic cont...

17 D Check of installation of the horizontal vane Start Replace the indoor electronic control P.C. board. Replace the safety device. Is the stopper of the horizontal vane locked to the indoor unit correctly? Yes No Is there resistance 0 " ? Relock the stopper of the horizontal vane to the indoor...

19 9.1 MS-GD08ND- C1 MS-GD10ND- C1 MS-GD12ND- C1 OPERATING PROCEDURE PHOTOS Photo 1 Screws of the panel 1. Removing the panel (1) Remove the screw caps of the panel. Remove the screws. (2) Pull the panel down to your side slightly and unhook the catches at the top. 2. Removing the electronic control...

HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN MITSUBISHI ELECTRIC CONSUMER PRODUCTS (THAILAND) CO., LTD. AMATA NAKORN INDUSTRIAL ESTATE 700/406 MOO 7, TAMBON DON HUA ROH, AMPHUR MUANG, CHONBURI 20000 THAILAND Made in Thailand New publication, effective Feb. 2008 Spec...