Mitsubishi 1998E- Manuals

3 3 3 Unpacking the Monitor Please check that the following items are included with your monitor. If theyare missing or damaged, please contact your place of purchase immediately. ♦ Monitor with attached signal cable ♦ Tilt/swivel base ♦ Power cord ♦ User’s manual Locate the model name and the seria...

5 5 5 Adjusting the Monitor Enter E x it 1 2 3 4 5 You can adjust the monitor using its On-Screen Display (OSD) menu system. There are 5 buttons that control the monitor: 1. Exit Returns to the last menu page, saves changes orquits the menu system. 2. and Move to another menu item or decrease the se...

6 Selecting Functions and Making Adjustments Contrast Hotkey 1. Press to open the contrast adjustment display. 2. Press or to adjust the contrast level. 3. Press the Exit button to save your changes. Brightness Hotkey 1. Press to open the brightness adjustment display. 2. Press or to adjust the cont...

8 5. Press Exit to save the setting and return to the main menu. 1. Luminance Contrast changes the difference between the light and dark areas of the displayed image. Brightness adjusts the brightness of the displayed image. 2. Geometry Hor. Position adjusts the horizontal position of the image. Hor...

9 Unbalance adjusts the pincushion balance if both sides of the image are bowed toward either the left or the right. Trapezoid makes the vertical edges of the image parallel. Parallelogram aligns the top and bottom edges of the image. Top corner adjusts the edge curvature at the top corners of the i...

10 4. Recall/Reset and Image Status Select and press Enter to recall the factory settings for the current graphics signal. The word “Recall” will blink on the screen in the process ofrecall. This page is also a status display that shows the horizontal and verticalfrequencies of the current graphics ...

11 Note: The setting of each parameter is represented by a numeric value andcorresponding scale. The on-screen menu will automatically disappear after 20-second’s ofinactivity. If changes have been made, the monitor will automatically save them. Timing and Refresh Rate Setting By making adjustments ...

12 Factory Preset Timings Mode Resolution Vertical Frequency (Hz) Horizontal Frequency (kHz) Industry 640 x 400 70 31.47 Industry 640 x 480 60 31.47 VESA 800 x 600 75 46.88 VESA 800 x 600 85 53.67 VESA 1024 x 768 75 60.02 VESA 1024 x 768 85 68.68 VESA 1280 x 1024 75 79.98 VESA 1280 x 1024 85 91.15 V...

13 6 6 Troubleshooting If you encounter any trouble using the Diamond View 1998E monitor, makesure that your monitor is properly installed. (For hardware installation, seeChapter 4 of this manual.) If the problems persist, please check this chapter for possible solutions before calling Mitsubishi El...

15 7 7 Specifications Model Diamond View 1998E Display Characteristics Display Type 19” (48 cm) diagonal cathode raytube Maximum Viewable Size 18” (45.7cm) diagonal Dot pitch 0.25 mm Surface coating Anti-Glare, Anti-Reflective, Anti-Static coating Graphics Signals Maximum Resolution 1600 x 1200 pixe...

16 User Interface Controls Mains power switch, On-ScreenDisplay with 4 control buttons On-Screen Display Functions: Contrast; Brightness; Vert. & Hor. Image Position and Size; PincushionAmplitude, Phase and Balance; Top and Bottom Corner Pincushion; ColorBalance; Degauss; Horiz. and Vert. Moire;...

17 8 8 Service Contacts If problems remain after checking this manual, please contact your place ofpurchase or contact Australian Service Contacts Visit the Mitsubishi Electric Australia web site at www.mitsubishi-electric.com.au For details of your nearest Mitsubishi Electric Authorised Service Cen...

18 Victoria and Tasmania 4 / 303 Burwood HwyEast Burwood, Vic, 3151 Telephone: (03) 9262-9899 Fax: (03) 9262-9850 Western Australia 5 / 329 Collier RoadBassendean, WA, 6054 Telephone: (08) 9377-3411 Fax: (08) 9377-3499 New Zealand Service Contacts Contact: Melco New Zealand Ltd.1 Parliament St.Lower...