Meyer Sound MSL-6 - Manuals

Page 2 - Declaration of Conformity; declares that the product:; conforms to the following Product Specifications:; Environmental Specifications for; Symbols Used

2 Made by Meyer Sound, Berkeley, CA, USA European Office: Meyer Sound Germany GmbHCarl Zeiss Strasse 1356751 Polch, Germany U ULL C C U ULL ® ® L I S T E D 3 K 5 9 C O M M E R C I A L A U D I O S Y S T E M According to ISO/IEC Guide and EN 45014 Declaration of Conformity The product herewith complie...

Page 3 - Voltage Requirements

3 Introduction The MSL-6, Meyer Sound’s largest self-powered speaker,is ideally suited for large-scale vocal public addressapplications as a stand-alone system, and for musicalsound reinforcement in combination with Meyer self-powered subwoofers and/or the DS-2P mid-bass speaker.The MSL-6 features a...

Page 4 - SHOOTING NOTE; Current Requirements; Power Connector Wiring Conventions

4 If the voltage decreases below the lower bound of eitheroperating range (brown-out), the supply uses storedenergy to continue functioning briefly. The unit turns offif the voltage does not increase above the thresholdbefore the storage circuits are depleted. The time that theMSL-6 continues to ope...

Page 5 - Safety Issues; Audio Input; The MSL-6 presents a 10 k; Case; produces a balanced input impedance of 500

5 Safety Issues Pay close attention to these important electrical andsafety issues. Use a power cord adapter to drive the MSL-6from a standard 3-prong outlet(NEMA 5-15R;125 V max). earth ground chassisground The MSL-6 requires a grounded outlet. Alwaysuse a grounding adapter when connecting toungrou...

Page 7 - Fans and Cooling System; Rigging; Dimensions

7 Fans and Cooling System The MSL-6 uses a forced-air cooling system with fourfans to prevent the amplifiers from overheating. The fansdraw air in through ducts on the front of the cabinet,over the heatsinks, and out the rear of the cabinet. Sincedust does not accumulate in the amplifier circuitry, ...

Page 8 - Complete Systems; Meyer Speaker Types

8 Measurement and SystemIntegration Measurement and correction tools are required toassemble a complete sound system, particularly whenthe venue requires precise array design, delay systems,or compensation for significant reverberation. Werecommend using the Meyer SIM® System II SoundAnalyzer and CP...

Page 9 - • Set the MSL-4 to the same polarity as the MSL-6 to

9 6 5 0 - P S u b w o o f e r s M S L - 4 D o w n - f i l l s I n p u t Mid-Hi Output Sub Output Input Output LD-1A Delay CP-10 EQ C H 1 C H 3 Input Output C H 5 CP-10 EQ Ch A A B Ch B M S L - 6 U p p e r M S L - 6 L o w e r CH 5 controls the MSL-4 down-fill system. Since themain system is more powe...

Page 10 - Driver Troubleshooting; Driver Troubleshooting with TPL; Low Driver Inspection and; Verifying Polarity; Driver Polarity in the Same Loudspeaker

10 Driver Troubleshooting The Remote Monitoring System (RMS) is the best methodto query the status of the drivers in a system before andduring the performance. RMS monitors peak power,peak voltage, and average voltage (VU) for each amplifierchannel, allowing immediate detection and muting fordrivers...

Page 12 - All units in inches; Top

12 Physical Construction Upper & Lower Braces 3 ⁄16 " Steel, ASTM A36 3 ⁄8 "-16 Reinforcement Rods, B7 Alloy Steel Fluid-Cooled High Frequency Driver, 4-inch Diaphragm (2-inch Throat) Fluid-Cooled Back- Vented 12-inch Cone Low-Frequency Driver 3 ⁄8 " Plywood Top & Bottom 3 ⁄16 &#...

Page 13 - Safety Summary

13 • To reduce the risk of electric shock, disconnect the loud- speaker from the AC mains before installing audio cable.Reconnect the power cord only after making all signalconnections. • Connect the loudspeaker to a two-pole, three wire grounding mains receptacle. The receptacle must be connected t...

Page 14 - Contact Information; Controls and Connectors

14 Meyer Sound Laboratories, Inc. 2832 San Pablo AvenueBerkeley, California 94702Telephone: 510 - 486 - 1166FAX: 510 - 486 - 8356 E-mail: [email protected]://www.meyersound.com Meyer Sound GermanyGmbh Carl Zeiss Strasse 1356751 Polch, GermanyTelephone: 49.2654.9600.58FAX: 49.2654.9600.5...