Maytag MMV5208WS - Manuals - manualsarea.com

Page 2 - INSTALLATION REQUIREMENTS; Tools and Parts; Tools Needed; Remove Cardboard Template; Special Requirements; For Wall Venting Installation Only:

2 INSTALLATION REQUIREMENTS Tools and Parts Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Parts Supplied For reorder information, see “Replacement Parts” section. NOTE: The hardware items listed he...

Page 3 - Installation Dimensions; Product Dimensions; Electrical Shock Hazard; WARNING; GROUNDING INSTRUCTIONS; For all cord connected appliances:

3 Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. *30" (76.2 cm) is typical for 66" (167.6 cm) installation height. Exact dimensions may vary depending on type of range/cooktop below. Product Dimensions Electr...

Page 4 - INSTALLATION INSTRUCTIONS; Remove Mounting Plate; Rotate Blower Motor; Wall Venting Installation Only

4 INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven. NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the m...

Page 5 - Roof Venting Installation Only

5 7. Reattach damper plate. Make sure damper plate tabs are inserted into the slots in the top of the microwave oven . 8. Secure damper plate with 2 screws removed in Step 1. Roof Venting Installation Only 1. Repeat Step 1 from “Wall Venting Installation Only.” 2. Repeat Step 2 from “Wall Venting In...

Page 6 - Possible Wall Stud Configurations; Figure 1; No Wall Studs at End Holes; Figure 2; Wall Stud at One End Hole; Figure 3; Wall Studs at Both End Holes; Figure 4

6 Locate Wall Stud(s) NOTE: If no wall studs exist within the cabinet opening, do not install the microwave oven.See illustrations in “Possible Wall Stud Configurations.” 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. 2. Mark the center of each stud, and draw a plum...

Page 7 - Mark Rear Wall; Drill Holes in Rear Wall

7 Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2. 1. Using measuring tape, find and clearly mark the vertical centerline of the opening. A. Centerline 2. Align the center markers on the cardboard template to...

Page 8 - Attach Mounting Plate to Wall

8 Installation for Wall Stud at One End Hole (Figure 3) 1. Drill a 3/16" (5 mm) hole into the wall stud at the end hole marked in Step 3 of “Mark Rear Wall.” 2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into the wall stud at the other hole marked in Step 6 of “Mark Rear ...

Page 9 - For Roof Venting Installation Only; Install Damper Assembly; Excessive Weight Hazard

9 5. Cut the 1 ¹⁄₂ " (3.8 cm) diameter hole at the circular shaded area “G” on the template. This hole is for the power supply cord. NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole, as shown. 6. Drill 3/8" (10 mm) holes at points “D”...

Page 10 - Complete Installation

10 NOTE: If microwave oven does not need to be adjusted, skip steps 7-9. 7. If adjustment is required, rotate microwave oven downward. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on a covered surface. 8. Loosen mounting plate screws. Adjust mounting plate and ret...

Page 11 - VENTING DESIGN SPECIFICATIONS; For optimal venting installation, we recommend:

11 VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood combination. ■ We do not recommend using a flexible metal vent. ■ To avoid possible product...

Page 12 - Recommended Vent Length; ASSISTANCE; Replacement Parts; Accessories

Recommended Vent Length A 3 ¹⁄₄ " x 10 " (8.3 x 25.4 cm) rectangular or 6 " (15.2 cm) round vent should be used.The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of ve...