Maytag MER8800FZ - Manuals

9 OVEN USE Odors and smoke are normal when the oven is used the first few times, or when it is heavily soiled. IMPORTANT: The health of some birds is extremely sensitive to the fumes given off. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well-v...

10 Key Press Tones Activates or turns off the tones when a keypad is pressed.1. Press SETTINGS until “KEY PRESS TONE” is displayed.2. Press START to display the current setting.3. Press the “3” keypad to adjust the setting.4. Press START to save the setting.5. Press CANCEL to exit. Tone Pitch Sets t...

11 Positioning Racks and Bakeware IMPORTANT: To avoid permanent damage to the porcelain finish, do not place food or bakeware directly on the oven door or bottom. Bakeware To cook food evenly, hot air must be able to circulate. Allow 2" (5 cm) of space around bakeware and oven walls. Make sure t...

12 Baking and Roasting Precision Cooking™ System - Precise Bake The Precise Bake system electronically regulates the oven heat levels during preheat and bake to maintain a precise temperature range for optimal cooking results. The bake and broil elements or burners cycle on and off in intervals. On ...

13 Cook Time To Set a Timed Cook: 1. Press BAKE, CONVECT BAKE or CONVECT ROAST. 2. Press the number keypads to enter a temperature other than the one displayed. 3. Press COOK TIME. The cook time oven indicator light will light up.4. Press the number keypads to enter the length of time to cook.5. Pre...

14 RANGE CARE Clean Cycle AquaLift ® Technology is an innovative cleaning solution that utilizes heat and water to release baked-on spills from the oven in less than 1 hour. This new cleaning technology is a low-heat, odor-free alternative to traditional self-cleaning options.Allow the oven to cool ...

15 General Cleaning IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Always follow label instructions on cleaning products. For additional information, you can visit the Frequently Asked Questions (FAQs) section of our website at www.maytag.com. Soap, wat...

16 Oven Light The oven light is a standard 40-watt appliance bulb. Before replacing, make sure the oven and cooktop are cool and the control knobs are in the off position. To Replace: 1. Unplug range or disconnect power. 2. Turn the glass bulb cover in the back of the oven counterclockwise to remove...

17 ACCESSORIES For accessories, you can visit our website at www.maytag.com/cookingaccessories. PROBLEM POSSIBLE CAUSES SOLUTIONS Oven cooking results not what expected Range is not level. Level the range. See the Installation Instructions. The temperature set was incorrect. Double-check the recipe ...

5 Electrical Requirements - U.S.A. Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Do not use an extension cord. Be sure that the electrical connection a...

6 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not remove the shipping base at this time. 4. On Ranges Equipped with a Storage Drawer: Remove the storage drawer. See the “Storage Drawer” ...

8 Electrical Connection - U.S.A. Only 1. Disconnect power. 2. Remove the terminal block cover screws located on the back of the range. Pull cover down and toward you to remove cover from range. 3. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block. 4. Add stra...

10 4. Use a Phillips screwdriver to connect the green ground wire from the power supply cord to the range with the ground-link screw and ground-link section. The ground wire must be attached first. 5. Use ³⁄₈ " nut driver to connect the neutral (white) wire to the center terminal block post with...

11 1. Part of metal ground strap must be cut out and removed. 2. Use a Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground link under the screw. 3. Pull the wires through the strain relief on bottom of range. Allow eno...

12 2. Attach terminal lugs to line 2 (red), bare (green) ground, and line 1 (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque ...

15 Moving the Range When moving range, slide range onto cardboard or hardboard to avoid damaging the floor covering. If removing the range is necessary for cleaning or maintenance: For power supply cord-connected ranges: 1. Slide range forward. 2. Unplug the power supply cord. 3. Complete cleaning o...