Maytag MDG20MNAGW0 - Manuals

5 DRYER SAFETY ■ The appliance is intended, but not limited, to be used in public areas. ■ Children of less than 3 years should be kept away unless continuously supervised. ■ The appliance must be disconnected from it's power source during service and when replacing parts. ■ If drum rotation is bloc...

6 MAINTENANCE INSTRUCTIONS If you need help, contact the dealer from whom you purchased the appliance, or a Maytag designated service company. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to yo...

8 DIMENSIONS/CLEARANCES Dimensions Clearances Side View Back View 743 mm ( 29 1 / 4 " ) 889 mm ( 35" ) 210 mm ( 8 1 / 4 " ) 25 mm ( 1" ) 660 mm (26") 83 mm ( 3 1 / 4 " ) 191 mm ( 7 1 / 2 " ) 38 mm ( 1 1 / 2 " ) 140 mm ( 5 1 / 2 " ) 273 mm ( 10 3 / 4 " ) 953 mm...

9 Your dryer can be installed in a basement, laundry room, or recessed area.This dryer is not intended for installation in a mobile home.Companion appliance location requirements should also be considered. IMPORTANT: Do not install or store the dryer where it will be exposed to the weather. Proper i...

10 INSTALLING LEVELING LEGS AND COIN BOX 1. Prepare dryer for leveling legs NOTE: Slide dryer onto cardboard or hardboard before moving to avoid damaging floor covering. Using two or more people, move dryer to desired installation location. Take tape off front corners of dryer. Open dryer and remove...

11 1. Remove cardboard from beneath dryer. Place a level on top edges of dryer, checking each side and front. If not level, tip dryer and adjust legs up or down as shown in Step 3, repeating as necessary. LEVELING Leveling your dryer properly reduces excess noise and vibration. Not Level LEVEL Not L...

12 ELECTRIC DRYER INSTALLATION REQUIREMENTS Electrical Requirements This is 3-wire appliance which must be earthed.Do not earth to a gas pipe.Failure to follow these instructions could result in death, fire, or serious injury. Electric Shock Hazard IMPORTANT: Observe all governing codes and ordinanc...

13 GAS DRYER INSTALLATION REQUIREMENTS Electrical Requirements EARTHING INSTRUCTIONS SAVE THESE INSTRUCTIONS IMPORTANT: Observe all governing codes and ordinances. You will need a grounded electrical outlet located within 610 mm (2 feet) of either side of the dryer. This dryer is supplied/fitted wit...

14 Gas Supply GAS DRYER INSTALLATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations. Gas Supply Before installation, check that the local gas distribution conditions, nature of gas and pressure, and the adj...

15 DRYER VENTING REQUIREMENTS WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations. Dryer exhaust must not be connected into any gas vent, chimney, w...

16 DRYER VENTING REQUIREMENTS 102 mm (4") Diameter Exhaust Hoods Box Hood Louvered Hood Angled Hood Vent Hoods Exhaust hood must be at least 305 mm (12") from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, bushes, or snow). Maximum Vent Length/Vent C...

17 DRYER VENTING REQUIREMENTS 1. Connect gas supply to dryer. If the flexible gas hose has 10 mm (3/8") BSP thread, use the supplied conversion thread adapter. Use pipe-joint compound resistant to the action of L.P. gas for gas connections. Make Gas Connection GAS SUPPLY CONNECTION (on some mode...

18 TECHNICAL SPECIFICATIONS – GAS DRYER 220–240V~50Hz 1ph 3A max. IP24 Clothes capacity: 9.0 kg max. Sound pressure level, Lpa: 58 dBA (uncertainty, Kpa: +/-10 dBA) Total mass: 68 kg max. Country: CH, CZ, CY, ES, GB, GR, HR, IE, IT, PT, SI, SK, TR CY, CZ, DK, EE, FI, GR, HU, IT, NO, RO, SE, SK, TR E...

19 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended earthing method. See “Electrical Requirements.” 2. Check that all parts are now installed. If there is an extra part, go back through the steps. 3. Check that you have all of your tools.4...

20 REVERSING DRYER DOOR SWING (OPTIONAL) You can change your door swing from a right-side opening to left-side opening, if desired. Remove the Door Assembly 1. Place a towel or soft cloth on top of dryer or work space to avoid scratching of the surface. 2. Open dryer door. Remove bottom screws from ...

21 ELECTRONIC CONTROL SETUP INSTRUCTIONS (PD & PN MODELS ONLY) General Information BLANK DISPLAY – This condition indicates the dryer is inoperative. Enter set-up mode to view diagnostic code. “0 MINUTES” SHOWING IN DISPLAY – This indicates the cycle is complete and the dryer cannot be operated....

22 ELECTRONIC CONTROL SETUP INSTRUCTIONS (PD & PN MODELS ONLY) Set-Up Codes ■ The NORMAL button will advance you from code to code. ■ The HEAVY DUTY button will change the code value. ■ The DELICATES button will select or deselect options. The set-up code is indicated by the one or two left-hand...

23 ELECTRONIC CONTROL SETUP INSTRUCTIONS (PD & PN MODELS ONLY) Code Explanation 1. 00 MONEY COUNTER OPTION This option is either NOT SELECTED “OFF” or SELECTED “ON.” 1. 00 Not Selected “OFF.” 1. 0C Selected “ON.” • Press the DELICATES button 3 consecutive times to select “ON” and 3 consecutive t...

25 Code Explanation J. Cd PAYMENT MODE (COIN/DEBIT OPTION) J. Cd Both coin and debit selected. Press the DELICATES button 3 consecutive times to change this selection. J. C_ Coins selected, debit disabled. Press the DELICATES button 3 consecutive times to change this selection. J._d Debit Card selec...

26 MODEL NOMENCLATURE:MDG – Maytag Gas MDE – Maytag Electric 20 – Model Type Number DRYER DISPOSAL CS – Coin Slide MN – Timer Non-Pay PD – Coin Drop PN – Electronic Non-Pay A – Series Revision G – Global W – White