Page 2 - DEFINITIONS OF SIGNAL WORDS; DEFINITIONS DES INDICATEURS PRINCIPAUX; DEFINICIÓNES DE LOS INDICADORES PRINCIPALES; DEFINITIONEN DER MARKIERTEN HINWEISE; DEFINIZIONI DEGLI INDICATORI PRINCIPALI
2 DEFINITIONS OF SIGNAL WORDS WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. NOTE: Emphasizes essential informatio...
Page 7 - ORIGINAL INSTRUCTION; RISK OF ELECTRIC SHOCK; WARNING: Before doing any; RISK OF HIGH TEMPERATURES; CAUTION: The compressor could; ENGLISH; WARNING
7 ORIGINAL INSTRUCTION INDEX1. SYMBOLS .......................................................................... 72. SAFETY INSTRUCTIONS .................................................. 83. SPECIFICATIONS ............................................................ 124. INSTRUCTIONS FOR OPERATION...
Page 8 - Non-side shielded spectacles and face; Only for EU countries; SAFETY INSTRUCTIONS; PRECAUTIONS ON USING THE COM-; IMPORTANT INFORMATION; WARNINGS on the compressor and in this
8 DO NOT USE IN THE RAIN Using the compressor in these or similar conditions will in-crease the risk of electric shock, dangerous malfunction, and overheating. WEAR SAFETY GLASSES OR GOGGLES Danger to the eyes always exists due to the pos-sibility of dust being blown up by the exhausted air or of a ...
Page 13 - ERATION; GROUNDING INSTRUCTIONS
13 4. INSTRUCTIONS FOR OP- ERATION Unpack the compressor and check for any defi-ciency, damage caused during transportation and loose bolts and screws. READ SECTION TITLED " SAFETY INSTRUC-TIONS "WEAR SAFETY GLASSES OR GOGGLES Danger to the eyes always exists due to the possi-bility of dust ...
Page 14 - Install it appropriately.; NEVER INSTALL THE MACHINE IN THE
14 4. NEVER USE THE MACHINE IN AN UNSTABLE PLACE. Never use it in a place where it could move or fall of itself.Be sure to install the compressor on a flat floor, with leg rubber underneath it; the al-lowable tilt angle of the floor is up to 10 de-grees. If the installation floor is tilted and slipp...
Page 17 - After turning off the machine power
17 4. MACHINE OPERATING PROCE- DURE Inspection and checkup prior to oper- ation • Prior to use, check the bolts and nuts for loosening and the parts for missing one. • The power supply used must be following specifications and be provided with a cir-cuit breaker. Allowable source voltage range is ±1...
Page 18 - Operating Procedure; Fully open the drain cock and turn the; and the general-purpose nailer or; Connect the high pressure hose to the
18 11. (Fig.D) Open the drain cock to discharge all the compressed air and water in the air tank. If you found any abnormalities in the check-up or inspection prior to the operation, send the machine to your dealer or authorized service facility for inspection or repair. Operating Procedure Before o...
Page 19 - Motor moan is generated.
19 5. PROTECTIVE DEVICE If internal heat builds up during operation due to clogging of the airflow orifice, if the machine is used in a highly heated environment or if an ab-normality occurs inside the machine, the thermal protector for preventing burnout may be activat-ed to stop the motor operatio...
Page 21 - Installation; compressed air from the tank.; Removal; Before operating the machine, be sure to; AUTOMATIC ADJUSTMENT
21 8. HOW TO INSTALL OPTION- AL 1260E TANK With AKHL1260E, you can add the optional AKTH13 air tank for 1260EX. If more air is re-quired, use the following steps to install the op-tional air tank. Installation 1. (Fig.G,K) Turn off the power switch of the compressor and unplug the power cord from th...
Page 22 - Implement the machine inspection on a; Neglect of this could cause a trouble or break it.; Inspect the machine every time you use it.; Month April
22 10.IN ORDER TO MAINTAIN PERFORMANCE 1. Drain water from the machine. After the work is finished, open the drain cock gradually to drain the compressed air and water in the air tank until the pressure gauge in the tank points to 0. • Not draining the water will result in the inside of the air tank...
