Magnum METROS-LS-WHTSLV - Manuals

5mm 4mm 1. Open the top cover, align the stem with the head tube and slide it on. Tighten the screw at the top of the stem. 2. Align the handlebar to be perpendicular to the wheel, then insert and tighten the two side-facing screws as shown below. 5mm Screw for adjusting the handlebar position 3. Mo...

2.Installation and Adjustment 2.2 Assembly of the Pedals Identify your pedals: check the letters on the pedals, “L” or “R”. The “R” marked pedal is for the right (when facing the forward direction). For attachment to the crank, tighten clockwise. The “L” marked pedal is for the left. For attachment,...

2.Installation and Adjustment 2.3 Seat Position To enable comfortable, fatigue-free and safe riding, the saddle and handlebar height should be adjusted to the body size of the rider. The saddle height is correct if the leg is near full extension while the foot is resting flat on the pedal in the bot...

2.Installation and Adjustment 2.4 Saddle Height The quick-release lever must require noticeable effort to put into fully closed position to prevent any unde- sired movement while riding. WARNING An improperly closed quick release lever can open again or have limited ability to keep the saddle in pla...

3.Battery and Charger 3.1 Overview A B C D E F Battery Charging Socket Battery Handlebar Capacity Level Light Power Button USB Port (on some batteries) WARNING Please ensure that the battery is locked in place before use A AC Plug¹ B Charger C Charging Indicator D Battery Plug ¹Type will vary C B D ...

Display Powering ON/OFF Press and hold the power button to turn on the display. A start-up screen (see image below) will display for aproximately 2 seconds before entering the main interface showing real-time information. To turn the display off press and hold the power button until the screen goes ...

Display Adjust Up Mode Function Adjust Down Power On 4. Display Indicators & Buttons Button Functions Power On: Turns the display on/off Adjust Up/Down: Changes the level of pedal assist during riding and switches functions in display settings Mode Function: Switches interface functions and ente...

Display 4.Display Pedal Assist Level Short press the arrow buttons to adjust the pedal assist level up or down. There are 5 PAS levels: ECO, TOUR, SPORT, TURBO, BOOST, and BOOST+. BOOST+ is indicated by a blinking BOOST icon. When PAS level is empty it means pedal assist is off.PAS levels do not swi...

Display Light Control Long press the adjust up button to turn the headlight on and off. While the headlight is on the display’s backlight is dimmed. Speed Indication The standard readout is real time speed, and can be switched to show average speed (AVG), and maximum speed (MAX).How to change speed ...

Display Battery Power Battery power is shown by a battery bar indicator and percentage. The battery bar divides the power level into 5 bars. After battery capacity is lower than 5% the display enters low voltage mode. In this mode the battery level shows 0 bars. The battery outline will start blinki...

Display Display Settings The following description explains how users can access the settings options in their display. Within 10 seconds of turning on the display, long press the M button to enter the settings interface.Short press the arrow buttons to switch between settings. Short press the M but...

Display Error Code Table Each error code corresponds to a specific fault in the system. The table below is intended for the e-bike own- er to use as reference when working with Magnum Bikes technical support or a certified Magnum dealer. If you still some questions about the display, please contact ...

5. Recommendations and Maintenance 5.1 General Requirements E-bikes use metal shells to cover the electric components, so we strongly advise against the use of exces- sive water to wash the shells and parts around them. Use a soft cloth with a neutral solution to wipe the dirt off the shells. Afterw...

Maintenance Schedule Each Ride Weekly Monthly 6 Months Yearly Tire Pressure X Tire Condition X Visual Inspection X Brake Lever Pressure X Quick Releases X Handlebar Alignment X Saddle Alignment X Battery Pack Locked X Wheel Check X Inspect Frame Condition¹ X Clean & Lubricate Chain X Check Brake...

5.3 Definition of Tampering and Recommendations Modifications to any part of your bike, such as the fork or frame, may make that part or the entire bike un- safe. A poorly installed or modified component can increase the stress on all other parts, greatly increasing their chance of failure. Modifica...

6. Warranty Your Magnum E-bike comes with a limited warranty. Please visit www.magnumbikes.com or your local Mag- num dealer for details. Bike must be registered at www.magnumbikes.com/warranty in order to be covered by the one year warranty. Stay Connected @magnumbikes @magnumbikes www.magnumbikes....