Lynx LN15ICE - Manuals

! CAUTION Outdoor Installation Do not install in a location where the ice machine will be exposed to direct sun exposure as this may result in unsatisfactory performance. Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the ice machine...

NOTE Figure 6 Electrical Connection Model Minimum Height Maximum Height LN15ICE 33 3⁄4" (85.7 cm) 34 3⁄4" (88.3 cm) Electrical Shock Hazard • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • This appliance should not, under any ci...

Door Reversing Instructions 1. Open door. 2. Loosen screw #1 and #2 using a Philips Screwdriver on top and bottom hinge. Slide door and remove the door from the unit. Figure 7 3. Once door is removed, using a Philips Screwdriver remove screws from magnet actuator located on inside and bottom of door...

INSTALLING THE DRAIN PLUMBING Access panel Drain pipe, (not provided) Drain tubing, cut to length and in- stall in the drain CL CL 14 7 ⁄ 8 " (37.8 cm) 11 ⁄ 16 " (17mm) 1 1 ⁄ 4 " (3.2 cm) 4 17 ⁄ 32 " (11.5 cm) 21 1 ⁄ 2 " (54.6 cm) Figure 12 Figure 11 Drain line coiled and secured...

Reverse osmosis, (RO), water, softened water, and de- ionized water are not recommended as they can adversely affect the quality and quantity of the ice. Water Supply Line Clamp and Screw Figure 14 Back view of ice machine NOTE ! CAUTION INSTALLING THE WATER SUPPLY Compression fitting Water supply l...

DRAIN SYSTEM TEST Procedure for Testing Drain System (both gravity and drain pump models) Drain pump models have a safety feature that will interrupt power to the unit if a high-limit condition occurs to prevent flooding. This safety feature can be initiated by a restriction in the drain system and ...

Figure 18 When the ice slab reaches the correct thickness, the ice sheet is released and slides onto the grid cutter (see Figure 18). Here, the ice slab is cut into squares by the grid cut-ter’s heated wires (see Figure 21). The water containing the dissolved minerals is drained after each freezing ...

The bin level sensor is located in the ice bin, it senses when the ice supply is low or full and starts or stops the ice making process accordingly. If the water supply is turned off to the ice machine be sure to set the electronic control to the “OFF” position or remove power to the unit. New Sound...

PRODUCT DIMENSIONS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" L N 15ICE 15" (38.1 cm) **34" to 35" (86.4 to 88.9 cm) 24" (61 cm) 14 7 ⁄ 8 " (37.8 cm) 33 3 ⁄ 4 ...

USING YOUR ELECTRONIC CONTROL Control Function Guide Function Command Notes ON/OFF Press and release. Unit will immediately turn ON or OFF. Enable Sabbath Mode Press and hold for 5 seconds and release The o F / o C symbol will flash briefly after 5 seconds. Interior light and display will go dark an...

! CAUTION CLEANING YOUR ICE MACHINE Forcing ice through the grid cutter will break the grid cutter wires. ! CAUTION Remove all ice from the evaporator plate and grid cutter area that is not embedded in wires Figure 26 Figure 27 Clean mode: To ensure maximum performance and ice quality, it is recomme...

! CAUTION CARE AND CLEANING AND ENERGY SAVING TIPS OBTAINING SERVICE Front Grille Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see page 4). SHOCK HAZARD: Disconnect elec...

• Never attempt to repair or perform maintenance on the appliance until the main electrical power has been disconnected. Turning the appliance control "OFF" does not remove electrical power from the unit's wiring. • Replace all parts and panels before operating. ! WARNING Electrocution Hazar...

PREPARING THE ICE MACHINE FOR STORAGE Draining and Removing Water from the Ice-Making System with a Gravity Drain. 1. Turn off the water supply to the ice machine. 2. Disconnect the water supply fitting at the inlet of the water valve. (See Figure 33a). 3. Change the electronic control to the "C...

PREPARING THE ICE MACHINE FOR STORAGE 8. Reconnect the water valve outlet water line. (See Figure 35 and 35a). 9. Reinstall the ice machine’s access cover. 10. Clean and dry the ice machine’s storage bin. 11. Prop the door open for air circulation to prevent mold and mildew. 12. Leave the water supp...

DRAIN PUMP REMOVAL INSTRUCTIONS Rear of ice machine Front of ice machine Remove the hex nut on front drain pump bracket with the 3 ⁄ 8 " socket then remove the bracket. Remove the hex nut on rear drain pump bracket with the 3 ⁄ 8 " socket then remove the bracket. carriage bolt carriage bolt ...

DRAIN PUMP REMOVAL INSTRUCTIONS Additional issues to be inspected by the installer upon service replacement: 1. The drain pump must be level. 2. No pinched water lines. 3. No interference with electrical cords or wiring. 4. The drain pump should not set on any obstacles, wiring, etc. 5. Secure all h...

HOUSEHOLD PRODUCT WARRANTY UNDERCOUNTER ICE MACHINE TWO YEAR FULL WARRANTY Undercounter ice machines and all of their component parts, except as detailed below*† , are warranted to be free from defective materials or workmanship in normal residential use for a period of two (2) years from the date o...

410164 1 1 Rev B 4/14 /2022 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. The best outdoor kitchen products come from:...