Liebherr SIGN2566LH - Manuals

Page 4 - Description of appliance; The; Sensor positions, schematic diagrams; Fan

Service Information No. 01/2008 IGN 2556/2566 Page 4/21 3.0 Description of appliance The IGN 2556/2566 is a NoFrost freezer using a series 6 control system with actual value display. The appliance has a lamellar evaporator with fan and integrated defrost heater. Two sensors, an air sensor and an eva...

Page 5 - Main components and their functions; Electrical components and functions; compartment; Electronic control system

Service Information No. 01/2008 IGN 2556/2566 Page 5/21 4.0 Main components and their functions 4.1 Electrical components and functions 4.1.1 General Electronic control system Type: Series 6 electronic control system Components: Electronic single-board solution 4.1.2 Freezer compartment Electronic c...

Page 8 - Compressor; Lamellar evaporator.; Type of installation:; In evaporator module on appliance ceiling

Service Information No. 01/2008 IGN 2556/2566 Page 8/21 4.2 Refrigeration components and functions 4.2.1 Freezer compartment Compressor Compressor: VCC, frequency-controlled Frame heater Position: Foamed-in in the housing, in the contact area of the magnetic door seal. Evaporator Type: Lamellar evap...

Page 9 - Assembly instructions / replacement of parts

Service Information No. 01/2008 IGN 2556/2566 Page 9/21 5.0 Assembly instructions / replacement of parts 5.1 General 5.1.1 Electronic control system Covers: Disengage covers at the marked points. Front panel: Unlock locating lugs at the left and right of the front panel. PCB carrier: Draw the front ...

Page 10 - magnet; Magnet

Service Information No. 01/2008 IGN 2556/2566 Page 10/21 5.1.2 Door magnet Magnet holder: Press marked locating lugs together and detach magnet holder upwardly. Fig. 5.1.2 / 1 Magnet holder

Page 11 - Top polystyrene moulding:

Service Information No. 01/2008 IGN 2556/2566 Page 11/21 5.2 Freezer compartment 5.2.1 Evaporator module Locking parts: Are snapped into place at the right and left for locking the evaporator module. Transit support: Remove the adhesive tape as transit support of the "top polystyrene moulding...

Page 12 - module; module

Service Information No. 01/2008 IGN 2556/2566 Page 12/21 5.2.2 Evaporator sensor Evaporator module: Dismantle the evaporator module as described below under 5.2.1 Evaporator module . Evaporator sensor: Is slipped inbetween the lamellas and in case of defect it has to be cut off and repaired with the...

Page 14 - fuse

Service Information No. 01/2008 IGN 2556/2566 Page 14/21 5.2.5 Temperature fuse Evaporator module: Dismantle the evaporator module as described below under 5.2.1 Evaporator module . Temperature fuse: Fastened by a screw. To be noted for replacement: - Cut off only at the coloured wires (not heater w...

Page 15 - IGN 2566 only, double solenoid valve IceMaker; Solenoid valve

Service Information No. 01/2008 IGN 2556/2566 Page 15/21 5.2.6 IGN 2566 only, IceMaker Holder: Press the locating lugs in the two openings of the holder inwards and draw the holder forwards for removal (see Fig. 5.2.6/ 1 ). Reed contact: The reed contact for drawer recognition is situated in the hol...

Page 16 - Air and evaporator sensors; Temperature °C; watts

Service Information No. 01/2008 IGN 2556/2566 Page 16/21 6.0 Technical data 6.1 General Sensor values: Air and evaporator sensors Temperature °C Resistance value kOhm +35 3.1 +30 3.8 +25 4.7 +20 5.9 +15 7.3 +10 9.3 +5 11.9 0 15.3 -5 19.8 -10 25.9 -15 34.1 -20 45.3 -25 60.8 -30 82.3 -35 112.8 6.2 Fre...

Page 17 - menu; defrosting

Service Information No. 01/2008 IGN 2556/2566 Page 17/21 7.0 Service menu The service menu may be used by service technicians only. Activation of service menu: Press " ON/OFF " + " SuperFrost " simultaneously for about 3 seconds Once the service menu is activated, the SuperFrost LED ...

Page 18 - mode

Service Information No. 01/2008 IGN 2556/2566 Page 18/21 7.3 Service mode Step Display Operation Display following operation Testing option / Info Service menu start 1 Actual value Press "ON/OFF" and "SuperFrost" simultaneously for 3 seconds "H" flashes with SuperFrost LED Se...

Page 19 - Table of error codes

Service Information No. 01/2008 IGN 2556/2566 Page 19/21 7.4 Sensor test (temperature display) and door contact test "E" Step Display Operation Display following operation Testing option / Info Service menu start 1 Actual value Press "ON/OFF" und "SuperFrost" simultaneously f...

Page 21 - (even after a waiting time of 90 seconds)

Service Information No. 01/2008 IGN 2556/2566 Page 21/21 8.2.2 Checking the compressor Fault profile: Compressor does not run (even after a waiting time of 90 seconds) Select step 6 (compressor ON) in the service menu under "7.3 service mode". If the compressor now starts there was probably ...