Liebert XDA - Manuals

Liebert XDA – Manual in PDF format online.

Manuals:

Manual

Manual Liebert XDA

Summary

Page 3 - TABLE OF CONTENTS

i TABLE OF CONTENTS 1.0 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 Equipme...

Page 4 - ii

Page 5 - CAUTION

1 1.0 P RODUCT D ESCRIPTION The Liebert XDA Air Flow Enhancer increases the airflow through densely populated enclosures, breaking up hot spots within the enclo-sure that can threaten the uptime of your critical systems. Equipment fans often produce insufficient flow to push air through the masses o...

Page 6 - NSTALLATION; Equipment Inspection; • Verify that the XDA unit voltage matches the available utility; NOTE; Check for interference with the cabinet’s handle/latch. If the

2 2.0 I NSTALLATION The Liebert XDA can be attached to most equipment cabinet doors 60" tall or taller. The unit typically is installed on the outside of a cabi-net’s rear door, generally used to discharge heat generated from the cabinet.If aisle space is insufficient for exterior mounting, and ...

Page 7 - XDA mounting; XDA with mounting bracket

3 2.2.1 Required Tools • Phillips screwdriver• Pliers• Scissors 2.3 Mounting the XDA on the Exterior of the Rear Cabinet Door 2.3.1 Prepare to Install the Unit 1. Determine the desired mount- ing position on the door. 2. Attach the mounting bracket to the top of the XDA, positioning the bracket to o...

Page 8 - Mount the Unit and Attach it to the Cabinet

4 2.3.2 Mount the Unit and Attach it to the Cabinet 1. Lift the unit with bracket attached and hang it on the door, as shown at right. Ensure that the bracket rests safely on top of the top edge of door. 2. Move the unit sideways into the desired position. Ensure that the unit does not interfere wit...

Page 9 - For mounting inside the cabinet, the mounting angles must

5 2.4 Mounting the XDA on the Interior of the Rear Cabinet Door 2.4.1 Prepare to Install the Unit 1. Remove the screws on the sides of the XDA that secure the mounting angles to the unit. 2. Remove the mounting angles. 3. Position the angles so their mounting surfaces are near the front of the XDA. ...

Page 10 - Mount the Unit and Attach It to the Cabinet; Eliminate Bypass Air; bypass air

6 2.4.2 Mount the Unit and Attach It to the Cabinet 1. Lift the unit onto the door, placing the two mounting holes on the top end, over the two screws attached to the door and bracket. Place nuts on the screws to hold the unit in place. 2. On the middle and lower mounting holes, place screws through...

Page 11 - Connect the power cords to separate power sources (as specified in; Specifications on page 9; ), to keep the XDA operating if there is a; Special tools are required for this.; At a point several inches below the unit and centered between the

7 3.0 P OWER C ONNECTIONS Connect the power cords to separate power sources (as specified in Specifications on page 9 ), to keep the XDA operating if there is a power failure on one circuit. Route the power cords under or over the cabinet as needed to the nearest available receptacles. If only one p...

Page 13 - PECIFICATIONS; Nominal Capacity

9 5.0 S PECIFICATIONS Nominal Capacity 1000 CFM @ 60Hz Dimensions W x D x H, in (mm) 8 x 2.25 x 56 (203.2 x 57.2 x 1422.4) Weight, lbs (kg) 25 (11.3) Electrical Specifications 120V-1-50/60Hz 230V-1-50/60Hz Amp Draw 1.5 A @ 120V 0.8 A @ 230V

Page 16 - Locations; EmersonNetworkPower.com

Ensuring The High Availability 0f Mission-Critical Data And Applications. While every precaution has been taken to ensure the accuracy and completeness of this literature, Liebert Corporation assumes no responsibility and disclaims all liability for damages resulting from use of this information or ...