Liebert Universal Monitor - Manuals

iv A PPENDIX A - S ERVICE T ERMINAL I NTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 A.1 Comparison of Functions: LCD and Service Terminal Interface. . . . . . . . . . . . . . . . . . . . . . 85 A.2 Connecting to the Service Terminal Interface . . . . . . ....

Introduction 1 1.0 I NTRODUCTION The Liebert Universal Monitor’s extensive capabilities can put it at the heart of your protective net- work. The Universal Monitor employs local alarming and remote paging services to keep personnel on-site and at remote locations apprised of the status of equipment....

Introduction 2 1.5 Outside Enclosure Overview The enclosure for the Universal Monitor’s controller board comes in two sizes: • The large enclosure is designed to accommodate the Transformer Module and future compo- nents, in addition to the controller board. • The small enclosure is built to hold th...

Introduction 3 1.6 Typical Configuration Figure 3 shows an example of external devices connected to the Universal Monitor’s controller board. There may be up to eight digital output, eight digital input and four analog input devices connected. The optional Universal Monitor Expansion Board provides ...

Introduction 4 1.7 Controller Board Overview The Universal Monitor’s controller board has connectors for eight digital inputs, four analog inputs and eight digital outputs, as shown below. The board comes complete with light emitting diodes (LEDs) to display the status of monitored devices, a batter...

Introduction 6 1.8 Optional Expansion Board Overview The Universal Monitor Expansion Board, purchased separately, has connectors for 16 digital inputs and eight digital outputs, as shown below. The board has light emitting diodes (LEDs) to display the status of monitored output devices, communicatio...

Introduction 7 1.9 LED Indicators The Universal Monitor’s controller board has LED indicators that show the status of inputs, outputs and the common alarm, as well as the modem and SiteScan Web connections. Table 3 LED indicators summary LED Type LED Color Description EIA422 LEDs 422 TX Green Univer...

Introduction 8 1.10 LED Indicators - Optional Expansion Board The optional Expansion Board, purchased separately, has LED indicators that show the status of inputs and outputs. Table 4 LED indicators summary LED Type LED Color Description Power status LED 24VAC Power (D6) Green 24VAC power is being ...

Introduction 9 1.11 Typical Sequence Figure 4 shows a typical sequence of how the Universal Monitor functions after detecting a change in a monitored unit or area. Many responses depend on configuration settings. This example shows what happens when an analog sensor input reaches a high setpoint—ass...

Installation - Main Board 10 2.0 I NSTALLATION - M AIN B OARD This section provides instructions for installing, mounting and connecting power to the Universal Monitor. For information on the optional Expansion Board, see 3.0 - Installation - Optional Expan- sion Board . 2.1 Installation Considerati...

Installation - Main Board 11 2.2 Surface-Mounting the Universal Monitor After determining where to place the unit, check to ensure that you have all the hardware required to install the panel on the surface of a wall. Obtain the needed tools and material. Required tools • Electric drill (if surface ...

Installation - Main Board 12 2.3 Flush-Mounting the Universal Monitor The Universal Monitor may be flush-mounted according to company practices—either with screws through the sides of the panel into wall supports or with hanging hardware that attaches to the back of the panel. After determining how ...

Installation - Main Board 13 2.4 Connect Power to the Universal Monitor The Universal Monitor requires 24VAC for proper operation. Liebert recommends using the optional Transformer Module manufactured by Liebert or another UL-approved Class 2 power unit to obtain proper voltage. If the power unit is...

Installation - Main Board 14 2.4.2 Termination and Mounting - Large Enclosure Input Power Connections To connect electrical power to the Transformer Module:1. Install electrical wiring from utility power to the Transformer Module.2. Use copper wires only; proper wiring to use for power is 14/2 AWG c...

Installation - Main Board 15 Troubleshooting - Transformer Module A common problem and possible solution are shown in the table below. For further information or if you have other problems with the unit, consult your local dealer, Liebert representative or the Liebert Worldwide Support Group. 2.4.3 ...

Installation - Optional Expansion Board 16 3.0 I NSTALLATION - O PTIONAL E XPANSION B OARD This section provides instructions for installing, mounting and connecting power to the optional Expan- sion Board. The Expansion Board enclosure is identical to the Universal Monitor’s small enclosure. 3.1 In...

Installation - Optional Expansion Board 17 3.2 Surface-Mounting the Optional Expansion Board After determining where to place the optional Expansion Board, check to ensure that you have all the hardware required to install the panel on the surface of a wall. Obtain the needed tools and material. Req...

Installation - Optional Expansion Board 18 3.3 Flush-Mounting the Optional Expansion Board The optional Expansion Board may be flush-mounted according to company practices—either with screws through the sides of the panel into wall supports or with hanging hardware that attaches to the back of the p...

Installation - Optional Expansion Board 19 3.4 Input Power Connections - Optional Expansion Board The optional Expansion Board requires 24VAC for proper operation. Liebert recommends using the optional Transformer Module manufactured by Liebert or another UL-approved Class 2 power unit to obtain pro...

Wiring and Connections - Main Board 20 4.0 W IRING AND C ONNECTIONS - M AIN B OARD 4.1 Wiring Specifications Input and output connections to the Universal Monitor may be made in any order—it is not neces- sary, for example, to make all input connections before making any output connections. Use copp...

Wiring and Connections - Main Board 21 4.2 Connecting Digital Inputs and Digital Outputs The digital inputs and digital outputs are found on the lower right side of the Universal Monitor’s printed wiring assembly board. There are two terminal blocks for the inputs—one green, the other black. There a...

Wiring and Connections - Main Board 22 4.2.3 Setting the Digital Output Jumpers Each digital output has an associated jumper to define its operation when power is interrupted and there is no battery backup to the board. This puts the Universal Monitor in a fail-safe mode and ensures proper functioni...

Wiring and Connections - Main Board 24 4.4 Connecting Common Alarm Outputs The common alarm relay, found in the top right corner of the Uni- versal Monitor, permits the user to connect auxiliary notification equipment, such as lights, horns and sirens, to the Universal Monitor. To determine the prop...

Wiring and Connections - Optional Expansion Board 25 5.0 W IRING AND C ONNECTIONS - O PTIONAL E XPANSION B OARD 5.1 Wiring Specifications Input and output connections to the optional Expansion Board may be made in any order—it is not necessary, for example, to make all input connections before makin...

Wiring and Connections - Optional Expansion Board 26 5.2 Connecting Inputs and Outputs The Universal Monitor’s optional Expansion Board permits the addition of 16 input and eight output devices. This section describes how to connect devices to the Expansion Board’s inputs and outputs.To determine th...

Wiring and Connections - Optional Expansion Board 27 5.2.2 Connecting Digital Outputs The eight digital outputs are found at the top of the Expansion Board, as shown below. These inputs are numbered 9 through 16. (Note that the digital outputs on the main board of the Universal Monitor are numbered ...

Wiring and Connections - Optional Expansion Board 28 5.2.3 Setting the Digital Output DIP Switches Each digital output on the optional Expansion Board has an associated DIP switch that can deter- mine its operation in the event of loss of communication with the Universal Monitor or loss of power. Wh...

Wiring and Connections - Optional Expansion Board 29 5.3 Connect to the Universal Monitor Two steps are required to establish connection between the optional Expansion Board and the Uni- versal Monitor. 5.3.1 Connect EIA485 Connectors to Main Board To connect the optional Expansion Board to the Univ...

Overview of Menus 30 6.0 O VERVIEW OF M ENUS There are two ways to access the Universal Monitor: the LCD on the front of the enclosure and the Service Terminal Interface, which is accessible through any computer using a communications pro- gram. Many viewing and configuration tasks can be performed ...

Overview of Menus 31 6.1 Opening Screen Overview The Universal Monitor displays the Opening Screen at startup, as shown in Figure 12 . • If any alarms are active, the Current Alarm screen appears. (Pressing any key on the LCD keypad will silence the audible alarm.) • If any analog input sensors are ...

View Status Options 32 7.0 V IEW S TATUS O PTIONS The View Status menu allows any user to view currently active alarms, monitoring data stored in the alarm, event and trend logs, the status of all inputs and outputs, and the four pager numbers. The arrows ↑ ↓ are used to scroll through the menu. The...

View Status Options 33 7.1 View Active Alarms The Active Alarm screen displays all alarms that are occurring, up to a maximum of 33.A Current Alarm screen appears automatically whenever an alarm occurs—except during setup. This screen can display only the two most recent active alarms. To view any o...

View Status Options 34 7.2 View Alarm Log The Alarm Log contains up to 99 records of alarms that have occurred. Records are added to this log as alarms occur.To view the Alarm Log: • From the Main Menu, use the arrows ↑ ↓ to choose View Status , then press Enter ↵ . • From the View Status Menu, use ...

View Status Options 35 7.3 View Event Log In addition to alarms, the Universal Monitor tracks other changes in the Event Log to assist users with verifying operational and trouble- shooting problems. Events reflect changes in the status of an input that is defined as an event or the change of state ...

View Status Options 36 7.4 View Trend Log The Universal Monitor takes readings of configured analog input sen- sors at regular intervals and stores them in four separate trend logs, one for each sensor. The time interval is 30 minutes. Each log contains up to 100 records.Follow these steps to select...

View Status Options 37 7.5 View Input Status The Input Status option allows you to view the current status of all inputs: the four analog sensor inputs and the eight digital inputs. If the optional Expansion Board is used, the additional 16 digital inputs can also be viewed.To view the Input Status:...

View Status Options 38 7.6 View Output Status The Output Status option allows you to view the current status of all eight outputs. If the optional Expansion Board is used, the additional eight digital outputs can also be viewed.To view the Output Status: • From the Main Menu, use the arrows ↑ ↓ to c...

View Status Options 39 7.7 View Pager Numbers The Universal Monitor may be set up to dial pager numbers when an alarm is detected. Up to four pagers may be configured, as described in 9.8 - Setup System - Setup Modem & Pagers . The View Pager Numbers option allows you to view the pager numbers a...

Silence Alarm & Backup Log Files (Service Terminal Interface) 40 8.0 S ILENCE A LARM & B ACKUP L OG F ILES (S ERVICE T ERMINAL I NTERFACE ) This section describes two features that are available in the Service Terminal Interface: • Silence Alarm• Backup Log Files 8.1 Silence Alarm (Service T...

Silence Alarm & Backup Log Files (Service Terminal Interface) 41 8.2 Back Up Log Files (Service Terminal Interface only) The Universal Monitor maintains three types of logs—alarm, event and trend—that may be backed up to a remote computer.This feature is available only through the Service Termin...

Silence Alarm & Backup Log Files (Service Terminal Interface) 42 5. At the top of the HyperTerminal window, shown below, click on Transfer , then on Receive File . 6. In the Receive File window, as shown above: • In the Place Received File in the Following Folder box, enter the name and location...

System and Control Options 43 9.0 S YSTEM AND C ONTROL O PTIONS The System and Control menu allows you to configure the Universal Monitor—setting up inputs and outputs and an input/output matrix to trigger actions, the modem and pagers, and system features such as date and time. This menu also provi...

System and Control Options 44 Figure 14 shows the main options available from the System & Control menu. Figure 14 Menu overview - System and Control menu Opening Screen UNIVERSAL MONITORDD-MON-YY HR:MM:SS VX.XXX.X PRESS ↵ =STATUS/SETUP Main Menu VIEW STATUS > SYSTEM AND CONTROL ↑ ↓ =NEXT ↵ =...

System and Control Options 45 9.2 Setup System - Overview The Setup System screen displays seven options that allow you to configure input and output devices and their relationships, the common alarm, the modem, pagers to be dialed when alarms occur, and a variety of system details, such as login pa...

System and Control Options 46 9.3.1 Change Label (Name of Input) Each input has a default label (Input_01, Input_02, etc.) that you may change to a more descriptive name for ease in recognizing alarms and events associated with the input. The label may consist of up to eight characters (see Table 20...

System and Control Options 47 9.3.4 Set Up Alarmable Inputs in Latched or Unlatched Mode Alarmable input points may be set up in Latched mode (Y), which requires the user to clear the Universal Monitor alarms after an alarm has occurred, or Unlatched mode (N), in which alarms will automati- cally cl...

System and Control Options 48 9.4 Setup System - Setup Common Alarm The audible alarm sounds after the Universal Monitor detects an alarm condition in any input that has been defined as alarmable, including digital and analog sensor inputs. Once the alarm is silenced, there are two options: • By def...

System and Control Options 49 9.5 Setup System - Setup Sensor The Universal Monitor has four analog sensor input points that may be configured individually. The panel monitors connected equipment for any 4-20 mA input—for example, temperature and humidity.To configure a sensor: Log In and Choose Set...

System and Control Options 50 9.5.1 Identify the Sensor as Connected To make use of an analog sensor, you must specify it as Connected (Y). By default, analog sensors are Not connected (N). • From the Setup Sensor Menu, choose Connected , as shown at right, and press Enter ↵ . • To change this featu...

System and Control Options 51 9.5.4 Change 4 mA Value For the 4 mA value, enter the smallest value for the range of the sen- sor—for example, 50°F for a temperature sensor with a range of 50°F to 90°F.The default value for each sensor is -999.9. Values that can be entered range from -999.9 to +999.9...

System and Control Options 52 9.5.7 Define Sensor as Alarmable or Event Each sensor may be defined as Alarmable (AL) or as an Event (EV). • For a sensor defined as alarmable, the following alarm reactions occur when the high-setpoint threshold is crossed: the LCD flashes, the audible horn sounds, co...

System and Control Options 53 9.5.9 Change Low Setpoint The Low Setpoint value is typically above the 4 mA value for the sen- sor. For example, if the 4 mA value is 50°F, the Low Setpoint might be 60°F. When the sensor crosses below this value, an alarm or event will occur, depending on the sensor c...

System and Control Options 54 9.5.11 Set Up Delay Time Each sensor may be set up with a specified time delay between the triggering of a high or low setpoint—a monitored sensor crosses the high or low setpoint threshold—and any response by the Universal Monitor. This feature can prevent transient co...

System and Control Options 55 9.6 Setup System - Setup I/O Matrix The Setup I/O Matrix menu allows you to configure the Universal Monitor’s digital and analog inputs to trigger various actions in any or all of the 16 outputs—eight on the main board and another eight if the optional Expansion Board i...

System and Control Options 56 Map Input to Expansion Board Output • From the Select Outputs menu, select Map to Exp Board if you want to map the selected input to an output on the optional Expan- sion Board. These outputs are identified as Outputs 9-16. • On the Output Map screen, you may map the se...

System and Control Options 57 9.6.2 Set Up Mapping for an Analog Sensor Input • Use the arrows ↑ ↓ to choose Map Sensor To Outpt from the Map Input/Sensor Menu, and press Enter ↵ . • From the Select Sensor Menu, choose the input you want—for example, Sensor_1 High Stpt —and press Enter ↵ . Map Senso...

System and Control Options 58 9.7 Setup System - Setup Output The Universal Monitor has eight outputs that may be configured indi- vidually. If the optional Expansion Board is used, its additional eight digital outputs may be renamed. The outputs may have a wide variety of Liebert or other manufactu...

System and Control Options 59 9.7.3 Set Expansion Board Output by DIP Switch If you choose Change State from the Setup Output Menu for an Expansion Board output (OUTPUT09-16), the screen displays a mes- sage that the state must be set by DIP switch, as shown at right.Each digital output on the optio...

System and Control Options 60 9.8 Setup System - Setup Modem & Pagers To use the modem and pager features, be sure to connect the phone line connector to a telephone wall jack using an RJ11 cord, as described in 4.6.2 - Phone Line Connector . 9.8.1 Modem Setup - Initialization String The Univers...

System and Control Options 61 Select Modem Setup 4. From the Setup System Menu, shown at right, use the arrows ↑ ↓ to choose Setup Modem&Pagers and press Enter ↵ . 5. Use the arrows ↑ ↓ to choose Setup Modem from the Pagers & Modem Menu and press Enter ↵ . 6. The Setup Modem Menu displays th...

System and Control Options 63 Enable Modem Diagnostic Messages Enabling modem diagnostics will provide the following additional information about the modem to the computer using the Service Terminal Interface: • At the Enable Modem Diagnostic Messages prompt, enter Y (Yes - enable) or N (No - disabl...

System and Control Options 64 9.8.3 Pager Setup - Pager Number and PIN The Universal Monitor may be configured to dial numeric or alphanumeric pagers when an alarm is detected. You may enter up to four pager numbers—all configured pagers will be dialed each time an alarm occurs. For each configured ...

System and Control Options 65 Enter a Pager Number • From the Setup Pager Menu, choose Setup Pager Number for the selected pager— Setup Pager 1 Number in the example at right—and press Enter ↵ . • See Table 30 for guidelines on entering the pager number, which may consist of up to 40 characters. To ...

System and Control Options 66 9.8.4 Pager Setup - Communications Check (Service Terminal Interface only) The Service Terminal Interface offers two additional options for pager setup, which are not available through the LCD interface: • Enable communications check• Enter time to perform communication...

System and Control Options 67 Enable Communications Check Enabling this function permits a daily communications test between the Universal Monitor and the selected pager. Once each day the Universal Monitor dials the pager at a specified time and sends this message: “UNIVERSAL MONITOR COMM CHECK.” (...

System and Control Options 68 9.9 Setup System - Setup System Info The Setup System Info options allow users to: • Change Password —used for access to system setup functions • Change Date & Time/Automatic Daylight Saving Time —used to set the Universal Monitor’s date and time and to enable autom...

System and Control Options 69 9.9.1 Change Password A password is required to access the Universal Monitor’s system and control options, as described in 9.1 - Login . The password consists of four characters (see Table 20 for valid characters). The default pass- word is AAAA. Change the Password To ...

System and Control Options 70 9.9.3 Setup Site ID You may enter a Site ID to identify the Universal Monitor’s location, using a name that may consist of up to 40 characters (see Table 20 for valid characters). The Site ID will appear with each alarm.To enter or change the Site ID: • From the Setup S...

System and Control Options 71 9.9.5 Backup and Upload Configuration File (Service Terminal Interface only) This operation may be performed only through the Service Terminal Interface. It permits the user to make a copy of the Universal Monitor’s configuration settings and save it as a file on the co...

System and Control Options 72 Back Up the Configuration File 8. At the prompt to Initiate a Backup of Configuration File, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[N] in the following example. 9. At the top of the HyperTerminal window, shown below, click on T...

System and Control Options 73 Upload the Configuration File 13. At the prompt to Initiate an Upload of Configuration File, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[N] in the following example. 14. At the top of the HyperTerminal window, shown below, click on...

System and Control Options 74 9.9.6 Setup Serv Ph Num - Enter Phone Number The Service Phone Number (Serv Ph Num) is used for remote monitoring by Liebert Global Services. The number is designed to allow remote monitoring services to connect to the Universal Monitor. All alarms will be sent to this ...

System and Control Options 75 9.9.7 Setup Serv Ph Num - Communications Check (Service Terminal Interface only) The Service Terminal Interface offers two additional options for setting up the Service Phone Number (Serv Ph Num) that are not available through the LCD interface: • Enable communications ...

System and Control Options 76 9.9.8 Factory Defaults At any time, you may restore all default values for settings in the Uni- versal Monitor as it was shipped. The password is the sole exception when reverting to the factory default settings. The password can be reset to the factory default of AAAA ...

System and Control Options 78 9.9.10 Initiate Remote Alarm Test (Service Terminal Interface only) The service phone number is used for remote monitoring by Liebert Global Services. The Service Ter- minal Interface may be used to test communications between the Universal Monitor and the service modem...

System and Control Options 79 9.10 Setup Exp Board - Optional Expansion Board By default, the optional Expansion Board is configured as Not connected (N). After connecting power to the board and connecting it to the Universal Monitor, you must specify the Expansion Board as Connected (Y), as describ...

System and Control Options 80 9.11 Manual Output Ctrl The Manual Output Ctrl feature allows you to manually change the state of any digital output to ON or OFF, overriding automatic control by the Universal Monitor (the default setting for all outputs). This menu also allows you to release the manua...

System and Control Options 81 9.12 Clear Alarms & Logs The Clear Alarms & Logs menu allows you to clear active alarms or delete all records from any of the Universal Monitor’s three logs: alarm, event and trend logs.To clear alarms or logs: Log In and Choose Clear Alarms & Logs • From th...

System and Control Options 82 9.12.3 Clear the Event Log The event log contains up to 99 records of events detected by the Uni- versal Monitor. You may want to clear the log after backing up the file or simply to free up space. To delete all records from the event log: • From the Clear Alarms / Logs...

Specifications 83 10.0 S PECIFICATIONS 10.1 Universal Monitor Specifications Power Requirements Small Enclosure Large Enclosure NOTE UMS02400 115VAC UML11500 230VAC UML23000 If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impair...

Specifications 84 10.2 Optional Expansion Board Specifications Power Requirements UMEXP NOTE If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. 24VAC ±10% of nominal; 50/60 Hz, 0.6A, 15VA Class 2 Dimensions W x D x H, in....

Service Terminal Interface 85 A PPENDIX A - S ERVICE T ERMINAL I NTERFACE The Service Terminal Interface allows access to all functions of the Universal Monitor, including some that are not possible through the LCD interface. This interface is accessible through any com- puter using a communications...

Connecting to the Service Terminal Interface 86 A.2 C ONNECTING TO THE S ERVICE T ERMINAL I NTERFACE This section describes how to set up and connect to the Service Terminal Interface. A.2.1 Connection Methods There are two ways to access the Service Terminal Interface: • Direct —Use a null modem ca...

Connecting to the Service Terminal Interface 87 A.2.2 Create a Connection Before connecting to the Service Terminal Interface, you must create a connection and specify the method to be used for connection, as described in the following steps.1. Start the HyperTerminal program—to do this, click on th...

Connecting to the Service Terminal Interface 88 A.2.3 Set Up the COM1 Port - Direct Connection Only The following steps apply only to setting up a direct connection to the Service Terminal Interface via the Universal Monitor’s RS232 port. If you are setting up a remote connection via modem, skip to ...

Connecting to the Service Terminal Interface 89 A.2.4 Set Up the Connection’s Properties The following steps are needed for both direct and remote connection to the Universal Monitor. Properties Setup 8. Open the Properties window by clicking on File , then on Properties , as shown below left. 9. In...

Connecting to the Service Terminal Interface 90 A.2.5 Connect to the Service Terminal Interface After creating and setting up a connection, use a communications program such as HyperTerminal to access the Universal Monitor’s Service Terminal Interface.1. Verify communications connections between the...

Overview of Menus 91 A.3 O VERVIEW OF M ENUS The Main Menu offers choices for viewing the status of the Universal Monitor, silencing the audible alarm and backing up the unit’s log files. It also allows access to the System and Control features, which require a password.The following shows where to ...

View Status Menus 92 A.4 V IEW S TATUS M ENUS The View Status menu allows any user to view currently active alarms, monitoring data stored in the alarm, event and trend logs, the status of all inputs and outputs, and the four pager numbers. Main Menu After connecting to the Service Terminal Interfac...

View Status Menus 93 A.4.1 View Active Alarms For details on this feature, see 7.1 - View Active Alarms . View Active Alarms ACTIVE ALARMS Input points/hardwarepresently in an alarm state SENSOR_1 101.1 DEGHIGH SETPOINT ALARM SENSOR_2 ------ DEGSENSOR PROBLEM INPUT_07 ALARMCONTACT OPEN BATTERYCHECK ...

View Status Menus 94 A.4.2 View Alarm Log For details on this feature, see 7.2 - View Alarm Log . View Alarm Log ALARM LOG Alarm history SENSOR_2 80.0 DEGHIGH SETPOINT ALARM29-AUG-02 09:29:10 MODEMINTERNAL FAULT29-AUG-02 09:20:10 INPUT_08 ALARMCONTACT CLOSED29-AUG-02 09:19:10 SENSOR_2 79.0 DEGRETURN...

View Status Menus 95 A.4.3 View Event Log For details on this feature, see 7.3 - View Event Log . View Event Log EVENT LOG Event history PAGERUNSUCCESSFUL PAGE07-MAY-02 10:29:10 OUTPUT01 MAN ONCONTACT CLOSED07-MAY-02 09:20:10 OUTPUT08 ONCONTACT OPEN07-MAY-02 08:20:10 OUTPUT08 MAN OFFCONTACT CLOSED07...

View Status Menus 96 A.4.4 View Trend Log For details on this feature, see 7.4 - View Trend Log . View Trend Log TREND LOG Trend historyfor each sensor Select sensor for trendyou want to view. 1=SENSOR_12=SENSOR_23=SENSOR_34=SENSOR_45=RETURN TO MAIN MENU SELECT A NUMBER:1 TREND LOG Trend history SEN...

View Status Menus 99 A.4.7 View Pager Numbers For details on this feature, see 7.7 - View Pager Numbers . View Pager Numbers PAGER & PIN NUMBERS Numbers to dial for an alarm PAGER 1 NUMBERA1,8005551212 PAGER 1 PIN01234567891011121314 PAGER 2 NUMBERA9W1,8005551212 PAGER 2 PIN01234567891011121314 ...

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 100 A.5 S ILENCE A LARM & B ACK U P L OG F ILES (S ERVICE T ERMINAL I NTERFACE ONLY ) This section presents two options from the Main Menu that are available via the Service Terminal Interface only. Main Menu After connectin...

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 101 A.5.2 Back Up Log Files (Service Terminal Interface only) For details on this feature, see 8.2 - Back Up Log Files (Service Terminal Interface only) . Back Up Alarm Log File Backup Log Files - Alarm Log File BACKUP LOG FILES...

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 102 Back Up Event Log File Backup Log Files - Event Log File BACKUP LOG FILES Backup alarm, event and trend log files 1=BACKUP ALARM LOG FILE2=BACKUP EVENT LOG FILE3=BACKUP TREND LOG FILE-SENSOR_14=BACKUP TREND LOG FILE-SENSOR_2...

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 103 Back Up Trend Log Files Backup Log Files - Trend Log Files BACKUP LOG FILES Backup alarm, event and trend log files 1=BACKUP ALARM LOG FILE2=BACKUP EVENT LOG FILE3=BACKUP TREND LOG FILE-SENSOR_14=BACKUP TREND LOG FILE-SENSOR...

Setup Menu 104 A.6 S ETUP M ENU The Setup menu allows the user to configure the Universal Monitor—setting up inputs and outputs and an input/output matrix to trigger actions, the modem and pagers, and system features such as date and time. This menu also provides a vehicle for manually changing the ...

Setup Menu 105 Setup Menu This section presents Service Terminal Interface screens for each of the following: * Setup System Information features are: • Change Password• Change Date & Time/Automatic Daylight Saving Time• Setup Site ID• Connect Battery• Backup and Upload Configuration File (Servi...

Setup Menu 107 Setup Input - Expansion Board Inputs SETUP INPUT Setup for discrete input points Select input to edit INPUT DEFINITION 1=INPUT_01 NO-EV-NL-00:012=INPUT_02 NO-AL-L -00:013=INPUT_03 NC-EV-NL-00:014=INPUT_04 NO-AL-L -00:015=INPUT_05 NC-AL-L -00:016=INPUT_06 NO-EV-NL-00:017=INPUT_07 NO-AL...

Setup Menu 108 A.6.2 Setup Common Alarm For details on this feature, see 9.4 - Setup System - Setup Common Alarm . Setup Common Alarm SETUP COMMON ALARM Select if the commonalarm relay contactis to reset withsilence alarm CURRENTSETTING 1=SETUP COMMON ALARM N 2=RETURN TO SETUP MENU3=RETURN TO MAIN M...

Setup Menu 109 A.6.3 Setup Sensor For details on this feature, see 9.5 - Setup System - Setup Sensor . Setup Sensor SETUP SENSOR Setup for analog input points Select sensor to edit SENSOR VALUE 1=SENSOR_1 80.0 DEG2=SENSOR_2 ------ DEG3=SENSOR_3 80.0 DEG4=SENSOR_4 79.5 RH5=RETURN TO SETUP MENU6=RETUR...

Setup Menu 113 Setup I-O Matrix - Map Input to Output - Expansion Board Inputs SETUP I/O MATRIX Program inputs & sensors to control outputs Select to map inputs or sensors 1=MAP INPUT TO OUTPUT2=MAP SENSOR TO OUTPUT3=RETURN TO SETUP MENU4=RETURN TO MAIN MENU SELECT A NUMBER:1 MAP INPUT TO OUTPUT...

Setup Menu 118 Setup Output - Expansion Board Outputs SETUP OUTPUT Setup for discrete output points Select output to edit OUTPUT DEFINITION 1=OUTPUT01 NO 2=OUTPUT02 NC 3=OUTPUT03 NO ****************** 4=OUTPUT04 NC NO=NORMALLY OPENED 5=OUTPUT05 NO NC=NORMALLY CLOSED 6=OUTPUT06 NC ****************** ...

Setup Menu 119 A.6.6 Setup Modem & Pagers For details on this topic, see 9.8 - Setup System - Setup Modem & Pagers . Pager Setup For details on this feature, see 9.8.3 - Pager Setup - Pager Number and PIN and 9.8.4 - Pager Setup - Communications Check (Service Terminal Interface only) . Setu...

Setup Menu 120 Modem Setup For details on this feature, see 9.8.1 - Modem Setup - Initialization String and 9.8.2 - Modem Setup - Additional Features (Service Terminal Interface only) . Setup Modem & Pagers - Modem Setup SETUP MODEM&PAGERS Input pager andmodem information Select pager or mod...

Setup Menu 121 A.6.7 Setup System Info This section presents Service Terminal Interface screens for choices 1 through 9 in the Setup System Information menu shown below. For details on this topic, see 9.9 - Setup System - Setup System Info . Change Password For details on this feature, see 9.9.1 - C...

Setup Menu 122 Change Date & Time/Automatic Daylight Saving Time For details on this feature, see 9.9.2 - Change Date & Time/Automatic Daylight Saving Time . Setup Site ID For details on this feature, see 9.9.3 - Setup Site ID . Change Date & Time CHANGE DATE & TIME CURRENT DATE &...

Setup Menu 123 Connect Battery For details on this feature, see 9.9.4 - Connect Battery . Backup and Upload Configuration File (Service Terminal Interface only) For details on this feature, see 9.9.5 - Backup and Upload Configuration File (Service Termi- nal Interface only) . Connect Battery CONNECT...

Setup Menu 125 Factory Defaults For details on this feature, see 9.9.8 - Factory Defaults . Firmware Update (Service Terminal Interface only) For details on this feature, see 9.9.9 - Perform Firmware Update (Service Terminal Interface only) . Factory Defaults RESTORE FACTORY DEFAULTS This command re...

Setup Menu 127 A.6.8 Connect Expansion Board For details on this feature, see 9.10 - Setup Exp Board - Optional Expansion Board . Connect Expansion Board CONNECT EXPANSION BOARD CURRENT SETTING 1=CONNECT EXPANSION BOARD N 2=RETURN TO SETUP MENU3=RETURN TO MAIN MENU SELECT A NUMBER:1 >IS THE EXPAN...

Setup Menu 129 Override Output - Expansion Board Outputs OVERRIDE OUTPUT Manually override an output point Select output to override OUTPUT CONTROL 1=OUTPUT01 AUTO 2=OUTPUT02 AUTO 3=OUTPUT03 AUTO ******************************************** 4=OUTPUT04 AUTO AUTO =CONTROL BY PANEL 5=OUTPUT05 AUTO MAN ...

Setup Menu 130 A.6.10 Clear Alarms & Logs For details on this topic, see 9.12 - Clear Alarms & Logs . Clear Active Alarms For details on this feature, see 9.12.1 - Clear Active Alarms . Clear the Alarm Log For details on this feature, see 9.12.2 - Clear the Alarm Log . Clear Alarms & Log...

Setup Menu 131 Clear the Event Log For details on this feature, see 9.12.3 - Clear the Event Log . Clear the Trend Logs For details on this feature, see 9.12.4 - Clear the Trend Logs . Clear Alarms & Logs - Clear the Event Log CLEAR ALARMS&LOGS Clear active alarmsor log records Select the lo...

Default Settings Quick Reference Guide 132 A PPENDIX B - D EFAULT S ETTINGS Q UICK R EFERENCE G UIDE This appendix provides a quick reference to default settings for the Universal Monitor and the optional Expansion Board. These settings also appear throughout the manual. Table 37 Universal Monitor -...

Default Settings Quick Reference Guide 133 Table 38 Universal Monitor - other default settings JUMPER SETTINGS Feature Default Other Options Digital output loss-of-power jumpers OFF - Normally Open ON - Normally Closed Note: Jumper position has no effect when the Universal Monitor has power. 12VDC/2...

Default Settings Quick Reference Guide 134 Table 39 Expansion Board - default settings for inputs and outputs DEFAULT SETTINGS - DIGITAL INPUTS (FROM TABLE 21) Feature Default Other Options LABEL INPUT_09 - INPUT_24 Any name (up to eight characters) NORM OPEN/CLOSE NO (Normally open) NC (Normally cl...

The Company Behind the Products With over a million installations around the globe,Liebert is the world leader in computer protectionsystems. Since its founding in 1965, Liebert hasdeveloped a complete range of support andprotection systems for sensitive electronics: • Environmental systems—close-co...