Liebert Network Card - Manuals

Worldwide Support Worldwide FAX Support U.S.A. U.K. France Germany Italy Netherlands E-mail Web site +1 614-841-6755+1 614-841-6755 1-800 222-5877 +44 (0) 1628 403200+33 (0) 1 43 60 01 77+49 89 99 19 220+39 02 98250 324+31 (0) 475 503333 [email protected] User Manual This Quick S...

Installing the Card The OpenComms Web Card is hot swappable and user-serviceable.Although you do not need to turn off the UPS, disconnect any loads, orrestart the UPS to install or remove the card, discretion should be used. CAUTION: The Intellislot Bay is located in close proximity to the UPS' outp...

5. Press "Enter" to see the Main Menu. If you do not see the Main Menu, press "Enter" again several times. If theMain Menu fails to appear, confirm that the blue configuration cable isinstalled properly, that your PC or terminal COM port is active, and thatyou are using the correct c...

Network Interface Menu Selecting Option "2" from the Main Menu opens the Network InterfaceMenu. Network Interface Menu-----------------------1: Speed/Duplex Auto2: Boot mode DHCP IP Address 0.0.0.0 Netmask 0.0.0.0 <ESC>: Cancel menu level Please select a key ?> From the Network Inte...

SNMP Communication Menu Liebert Network Interface Card SNMP Communications Menu-------------------------1: Authentication Traps 'no'2: Display/Modify Communities3: Display/Modify Trap Communities <ESC>: Cancel menu level Please select a key ?> Selecting Option "3" from the Main Menu...

The options "a" "d" and "e" allow you to manage you list of networkdevices that will receive SNMP Traps from the card. These options canbe used as a complex instruction to add a single device and designate theCommunity String. For, example, entering: "a 126.4.1.200 NewCom...

Web Server Menu Web Server Menu----------------1: Web Server 'enabled'2: Change Username/Password <ESC>: Cancel menu level Please select a key ?> Selecting Option "4" from the Main Menu opens the Web Server Menu. From the Web Server Menu you can enable/disable the Web functionalityo...

Firmware Updates Menu Firmware Updates Menu----------------------1: Initiate XMODEM session... <ESC>: Cancel menu level Please select a key ?> Selecting Option "5" from the Main Menu opens the Firmware UpdatesMenu. From the Firmware Updates Menu you can reload the firmware of thecar...

Factory Settings Menu Factory Settings Menu----------------------1: Reset to Factory Defaults Manufacture Date OCT 27,2000 MAC Address 00-00-68-16-00-03 Serial Number 415981G101D2000OCT270003 <ESC>: Cancel menu level Please select a key ?> Selecting Option "6" from the Main Menu ope...

Opening a Web Connection This section explains the Web interface in detail. From the Web, you canmonitor and control the UPS in which the card is installed. You can alsoconfigure many settings of the card. NOTE: To specify that the card communicates at either 10Mbit or 100Mbit, instead of it trying ...

Connected Device Information Clicking between the monitor, contol, configure, and support tabs givesyou access to folder lists on the bottom of the left pane. Although thefolder list changes, depending on the tab selected, the top portion of theleft pane remains constant. In the top or the left pane...

Security By opening a connection to the OpenComms Web Card, you are able todo three things. You can Monitor, Configure and Control the UPS. The card allows any user with access to the network segment on which itresides to monitor the UPS. This means anyone on the segment canview the entire contents ...

Monitor Tab When you select the monitor tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. TheFolder list is at the bottom of the pane under Device Information:. The first page you will see every time you open a new Web connection tothe card is the...

Control Tab When you select the control tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. TheFolder list is at the bottom of the pane under Control Operations:. As detailed in the Web Security section, a Username and Password pro-tect the folders ...

Configure Tab When you select the configure tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. TheFolder list is at the bottom of the pane under Configuration Categories:. As detailed in the Web Security section, a Username and Password pro-tect th...

Configure Tab - Making and Saving Configurations Similar to configuring the card using the Service Terminal, every time youmake a configuration change, the card will have “save and reboot” for thatchange to take effect. As you navigate between the card's control webpages, you will notice that config...

Configure Tab - After Reinitialization Once card reinitialization is selected and confirmed, the card is unavail-able on the network. As the card reboots, it first begins communicatingon the network and it will begin communicating with the UPS in which it isinstalled. The card will present to you so...

Support Tab When you select the support tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. A sin-gle device list is at the bottom of the pane under Support:. The support tab displays the Name, Location, and Description fields aswell as relevant con...

The OpenComms Web Card utilizes a SNMPv1 agent and is MIB-II com-pliant. The card supports the open standard UPS MIB RFC1628, withadditional functionality and support through the Liebert Global ProductsMIB. A copy of the Liebert Global Products MIB is included on the CDincluded with your purchase. L...

MultiLink Support The most frequently asked question about configuring MultiLink to moni-tor a SNMP device, like the OpenComms Web Card, across the networkis, what community string do I use? NOTE: Use the community string LiebertEM for MultiLink. Configuring for MultiLink support from the Service Te...