LG WD(M)-80130F - Manuals

2-2.DETERMINE WASHING TIME BY FUZZY LOGIC To get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount. 2-3.WATER LEVEL CONTROL This model adopts a pressure sensor which can sense the water level in the tub. When the ...

3. PARTS IDENTIFICATION 6 Drain hose Wrench Power plug Control panel Door Lower coverAdjustable feet (For detergent and fabric softener) Drawer Drum Lower cover cap Drain pump filter Drain plug If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a similarl...

Before servicing ask the customer what the trouble is.Check the adjustment (power supply is 220-240V, remove the transit bolts....)Check the troubles referring to the troubleshooting.Decide service steps referring to disassembly instructions.Then, service and repair.After servicing, operate the appl...

TEST OPERATION 9 Connect the power plug to In case of cotton program. the outlet. Connect the inlet hose. Preparation for Press the power button. Press the START/PAUSE washing. button. Check if the drum rotates Check if water is supplied clockwise and counterclockwise. through the detergent dispense...

11 Rinse Hold No Spin 400 800 1000 Cold 30 40 60 95˚C Time Save Pre Wash Crease Care Rinse+ Spin Temp. Option Option Rinse+ : If you wish torinse more, the Rinse+option will remove anytrace of detergents. Crease Care : If you wantto prevent crease, selectthis function afterselecting spin speed. Wate...

ERROR SYMPTOM 1 WATER INLET Water has not reached to the pre-set level within 4 min. since ERROR inlet valve operated, or water has not reached to the normal level within 25 min. 2 IMBALANCE The appliance is tilted. ERROR Laundry is gathered to one side. Non distributable things are put into the dru...

SYMPTOM GUIDE FOR SERVICE CALL NO POWER Water inlet trouble 17 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION 8. ERROR DIAGNOSIS AND CHECK LIST YES YES YES NO NO YES NO NO Is the power plug connected firmly to 220-240V~ outlet? Power failure? or Breaker opened? Is the outlet controlled by a switch....

18 SYMPTOM GUIDE FOR SERVICE CALL DOOR OPEN ERROR Refer to 7-3 ERROR DISPLAY Drain Trouble NO YES YES NO NO YES Did you press the Start/Pause button when the door is open? Visit to check Check if the door switch is O.K Is displayed? Is the debris filter clogged with foreign material such as pins, co...

19 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No effect of softener YES YES YES YES YES Is low-sudsing detergent for the durm washing machine used? Is the proper amount of detergent used as recommended? Recommend to red...

20 8-2.FAULT DIAGNOSIS AND TROUBLESHOOTING 1. Be careful of electric shock or disconnecting the parts while troubleshooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the PWB assembly (Main), put in the connectors correctly. CAUTION NO NO YES ...

21 NO YES NO YES NO YES NO NO YES YES YES NO NO NO YES Wiring diagram option (HOT) option (HOT) MAX m a x Is the water supply shut-off? Is the tap opened? Is the inlet valve filter clogged with impurity? Is resistance of the inlet valve connector between the 2 to 8 k ? Check the voltage between each...

22 YES YES YES NO NO NO NO NO YES YES YES YES Wiring diagram option (HOT) MAX m a x ABNORMAL SOUND SOFTENER DOES NOT FLOW IN Fix the bolt tightly. Replace the V-belt(4400FR3116A) Replace the motor. Refer to NO WATER SUPPLY Check the wiring on the dispenser. Put it in the correctcompartment. Clean th...

23 YES YES NO NO NO NO YES YES NO PWB ASSEMBLY PWB ASSEMBLY YES NO 1 2 Clean the air chamberand hose.Replace the sensor. (pressure) Repair drain hose Remove foreign material. Reconnect or repair theconnector Replace the pumpassembly Replace the PWB Are there any problem at air chamber, the hose or p...

24 NO YES YES WASH HEATER TROUBLE 4 1 AC 220-240V NO NO YES NO YES (1) Replace the thermistor(6322FR2046B) Push the thermistor tightly to the rubber. When disconnect the connector (1) on the PWB assembly is the resistance of the Natural connectors ( White), (Blue / White) between 2.5k to 180k (105 ~...

25 3 4 2 1 1 10 1 2 3 4 5 6 7 8 9 10 5 YES YES YES NO NO NO YES Temp. Option SPIN TROUBLE Normal. Reconnect or repair it. Replace the motorassembly.(4681FR1194A) or(4681FR1194B) Check the sensor (Pressure) or hose (Sensor). If the problem is on the sensor or the hose,replace the sensor or the hose. ...

26 Be sure to unplug the machine out of the outlet before disassembling and repairing the parts. 9. DISASSEMBLY INSTRUCTIONS Unscrew 2 screws on the back of the top plate. Pull the top plate backward and upward as shown. Disconnect the PWB Assembly connector from Main lead wire Assembly. Pull out th...

27 Disassemble the top plate assembly. Pull out the drawer to arrow direction. Unscrew 2 screws. The hose clamps and the hose are disassembled. The ventilation bellows and the water inlet bellows are disassembled on the tub. Option DISPENSER ASSEMBLY DISPENSOR ASSEMBLY DRAWER

29 Take apart the cabinet gasket clamp. Unscrew 2 screws from the cabinet cover. Open the lower cover cap and unscrew 1 screw inside. Take apart the lower cover. Unscrew all the screws on the upper and lower sides of the cabinet cover. Take apart the tub gasket clamp. Make sure that the drain hole o...

30 Remove the back cover. Take off the belt turning the pulley. Unscrew the bolt to pull out the pulley. Unscrew 2 screws from the bracket. Push the motor in the arrow direction for disassembling. When reassembling the motor, make sure that motor mounting bushings are not taken off from the bracket....

Cap (Remaining Hose) Screw Pump Outlet Hose Tub Pump Bellows 31 Remove pump outlet hose. Remove tub pump bellows. Remove cap (Remaining Hose.) Disconnect the wiring. Unscrew 2 screws. Remove the pump. Loosen the M6 heater nut to pull out the heater. When mounting the heater, be sure to insert the he...

10-1.THE EXPLODED VIEW OF CABINET ASSEMBLY 33 10. EXPLODED VIEW A485 A480

10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSEMBLY 34 F430 A450

10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLY 35 K330 K332 K333