LG WD-1433RD - Manuals

3. PARTS IDENTIFICATION 6 ACCESSORIES Synthetic Wool Hand W ash Drain Cotton C Eco Delica te Quick3 0 Rinse+S pin Spanner

Before servicing ask troubles of customersCheck the adjustment(power supply is 220-240V~, remove the transit bolts....)Check the troubles referring to the trouble shooting.Decide service steps referring to disassembly instructions.And then, service and repair.After servicing, operate the appliance w...

TEST OPERATION 9 Connect the power plug to the outlet. In case of Coloreds program. Connect the inlet hose. Preparation for Press the POWER button. Press the Start/Pause washing. button. Check if the drum rotates Check if water is supplied clockwise and counterclockwise. through the detergent dispen...

10 5. OPERATION LED display Display the estimated remaining time (Hour : Minute) to finish. In case of abnormal operation, errorindications are displayed. ( ) See troubleshooting guide. Water temperature selector Press the button to select watertemperature.95 C is selected for Cotton only.By pressin...

11 • For additional rinse which may assist inremoving traces ofdetergent residue. • By selecting Rinse+ function, the rinse timeand the rinse water areincreased. • If the laundry is heavily soiled, “Pre Wash”course is effective. • Pre Wash is available in Cotton and Synthetic. • If you want Dry, sel...

12 6. WIRING DIAGRAM / PROGRAM CHART * Water Supply : W ·S * Intermittent Spin : I·S * Disentangle : D ·T * Basic Cycle* Optional Cycle * Pre-Setting Time : Water Supply - 120 sec. * Basic time is minute in washing chart Drain - 60 sec. * The actual program time can be varied with the load amount , ...

13 7. TROUBLE SHOOTING 7-1.BEFORE PERFORMING SERVICE Be careful of electric shock or disconnecting the parts while troubleshooting. Voltage of each terminal in 220-240V~ and DC while applying an electric current. 7-2.QC TEST MODE. Press Intensive and Rinse Hold button simultaneously. Power supply on...

14 7-5.ERROR DISPLAY. If you press the Start/Pause button in error condition, any error except ‘ ’ will disappear and the machine will change into pause status. In case of if the error is not resolved within 20 sec., and in case of other errors, if the error is not resolved within 4 min., power will...

16 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION 8. ERROR DIAGNOSIS AND CHECK LIST SYMPTOM GUIDE FOR SERVICE CALL NO POWER Water inlet trouble YES YES YES NO NO YES NO NO No Inlet Is the power plug connected firmly to 220-240V~ outlet? Power failure? or Breaker opened? Visit to check Is " "...

17 SYMPTOM • Door does not open• Error displayed on the program • DRAIN TROUBLE GUIDE FOR SERVICE CALL NO YES NO YES Started with door opened? NO YES Is the debris filter clogged with foreign material such as pin, coin and etc.? Is the drain hose frozen with water, kinked or crushed? Visit to check ...

18 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No effect of softener YES YES YES YES YES Is low-sudsing detergent for the drum washing machine used? Is the proper amount of detergent used as recommended? Recommend to red...

19 8-2.FAULT DIAGNOSIS AND TROUBLE SHOOTING 1. Be careful of electric shock or disconnecting the parts while trouble shooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the MAIN PWB ASSEMBLY, Put in the connectors correctly. NO NO YES YES YES ...

20 NO YES NO NO YES NO YES YES NO NO YES YES YES NO NO NO YES Wiring diagram Option Option MAX max Is water supply shut-off? Is the tap opened? When you press both Rinse button and Spin buttonsimultaneously, is the water level frequency below242? Is the inlet valve filter clogged with impurity? Is r...

21 YES YES NO NO NO NO YES YES YES YES Wiring diagram Option MAX max A B N O R M A L S O U N D S O F T E N E R D O E S N O T F L O W I N Fix the bolt tightly. Replace the STATORASSEMBLY or ROTORASSEMBLY. Refer to NO WATER SUPPLY Check the wiring on the dispenser. Put it in the correctcompartment. Cl...

22 NO YES YES YES YES NO NO NO NO YES YES NO MAIN PWB ASSEMBLY MAIN PWB ASSEMBLY 220-240V 2 1 Replace the S.PRESSURE SWITCH ASSEMBLY Replace the MAIN PWBASSEMBLY Repair the DRAIN HOSE ASSEMBLY. Remove foreignmaterial. Reconnect or repair theconnector Repair the DRAIN PUMP ASSEMBLY. Repair the MAIN P...

23 NO YES YES WASH HEATER TROUBLE When checking the voltage betweenconnectors ( , ) during whites washing, Is the voltage220 - 240V ? Replace the MAIN PWBASSEMBLY YES NO After power off and the heater terminal isdisconnected, is the resistance 10~30 ? Replace theHEATER ASSEMBLY NO After power off,is...

24 NO YES YES YES NO NO YES NO NO YES 1 2 1 3 4 2 SPIN TROUBLE Check the sensor(Pressure) or hose(Sensor). If the problemis on the sensor or thehose, replace the sensoror the hose. Normal Correct the connector. Correct the connector. Replace the STATORASSEMBLY(4417EA1002D) Check on the spinning, is ...

Rinse Spin Wash Rinse NO YES YES (1) Yellow (1)(2)(3) (1) (3) (2) (1) 27 D O O R D O E S N O T O P E N Is ^ ^ Door lock _ _ Display lamp on? After draining and ^ Door lock _ lamp off, open the door. Check switch Assembly,Door lock connector andMain PWB ASSEMBLY. Is ^ ^ _ _ Displayed? ,

9. DISASSEMBLY INSTRUCTIONS Disassemble and repair the parts after pulling out power cord from the outlet. CONTROL PANEL PLATE ASSEMBLY (TOP) Hook Control Panel Assembly Control Panel Assembly Unscrew 2 screws on the back of the top plate. Pull the top plate backward and upward as shown. Disconnect ...

30 ① Disassemble the Top Plate Assembly. ② Pull the drawer to arrow direction. ③ Two screws are unscrewed. ① The hose clamps and the hose are disassembled. ② The ventilation bellows are disassembled on the tub. DISPENSER ASSEMBLY DISPENSER ASSEMBLY PUSH

31 ① Disconnect the wiring connector. ② Remove the valve by two screws of the valve holder. When reconnecting the connector 2 1 3 4 INLET VALVE VALVE (DRY) YL/BK - BK VALVE (PRE-WASH) GY/WH - BK VALVE (NORMAL-WASH) WH/BK - BK VALVE (HOT) BL/RD - BK ① Remove the lower cover to arrow direction after o...

32 ① Open the door completely. ② Remove the two screws from the hinge. ※ When removing the Door Assembly, it is necessary to hold the Bracket that is inner ofthe Cabinet Cover. DOOR Take apart the CLAMP ASSEMBLY (cabinet). Unscrew 2 screws from the CABINET COVER. Open the lower cover cap and unscrew...

33 ① Remove the back cover. ② After loosening the bolt, Rotor, pull out the rotor. ① Remove the 6 bolt from the stator. ② Disconnect the 2 connectors. ① Remove the bolts at the Tub. ② The Hinge(Damper) at the base is pulled offpressing on the snaps at the sharp end. ③ The hinge at the base is pulled...

① Remove pump outlet hose. ② Remove tub pump bellows. ③ Remove cap(Remaining Hose). ④ Disconnect the wiring. ⑤ Three screws are unscrewed from the cabinet. ⑥ Remove the pump to arrow direction. ① Loosen the nut. ② Remove washing heater by pulling out. When assembling the washing heater, insertthe he...

① The cabinet cover clamp is removed and thegasket is released. ② Two screws are unscrewed. ③ The door lock S/W is disconnected form thewiring connector and the strap. ① Remove washing heater. ② Remove the foreign object(wire,coin,etc) byinserting long bar in the hole. SWITCH ASSY, DOOR LOCK WHEN FO...

① Remove 6 screws and dry fan assembly. ② Remove 7 screws and dry duct upper. ① Remove 1 screw and dry heater. ② Remove thermostat. ① Remove 17 screws from Dry duct upper and Dry fan Assembly. ① Remove 5 screws and condensing duct. Dry fan Ass'y Dry Duct Upper DRY DUCT Dry Heater Thermostat 36

10-1.THE PART LIST OF CABINET ASSEMBLY 10. EXPLODED VIEW AND PART LIST 37

10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLY 39

10-4 THE EXPLODED VIEW OF DRYER :Non-service part :Service part M217 M216 40