LG W1942TQ - Manuals

LG W1942TQ – Manual in PDF format online.

Manuals:

Manual

Manual LG W1942TQ

Summary

Page 2 - On Safety; Do not Open the Display.; Important Precautions

A1 This unit has been engineered and manufactured to ensure your personalsafety, however improper use may result in potential electrical shock or firehazards. In order to allow the proper operation of all safeguardsincorporated in this display, observe the following basic rules for itsinstallation, ...

Page 3 - On Installation; screen because over-spraying may cause electrical shock.; On Repacking

A2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a ...

Page 4 - Connecting the Display; Important; Connecting the stand; Place the monitor with its front facing downward on a soft cloth.; Tie down the base lock to perpendicularity direction.; Once assembled take the monitor up carefully and face

A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot. Before setting up the m...

Page 5 - Disassembling the stand; Pull out the Stand to remove.

A4 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflatsurface. 3. Change your lock on the product as it follows and turn it in the arrow direction. 2. Place the monitor face Down onthe cushion or soft cloth. If you can't release the stand base even the locking knob...

Page 6 - Positioning your display; Ergonomic; Pushing the PUSH button, Take the stand base from stand body.; You can hurt your finger.

A5 Connecting the Display 20 Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Ergonomic It is recom...

Page 7 - Using the Computer; to; Connect DVI Cable; NOTE

A6 Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch mapform to . 1 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) 2...

Page 8 - Control Function; Control Panel Functions; MENU Button; Use this button to enter or exit the On Screen Display.; The message; MENU button; for several seconds. The message; Front Panel Controls

Control Function A7 Control Panel Functions MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds. The messa...

Page 9 - Use this button to turn the display on or off.; Power Button; button before entering the On Screen; Buttons

Control Function A8 Control Panel Functions This Indicator lights up blue when the displayoperates normally(On Mode). If the display is in SleepMode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off. Power Button Power Indicator Use this button to ...

Page 10 - On Screen Display (OSD) Control Adjustment; Screen Adjustment; MENU

A9 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters ofthe display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.The follow...

Page 11 - On Screen Display(OSD) Selection and Adjustment; PICTURE; POSITION VERTICAL; FLATRON

A10 NOTE The order of icons may differ depending on the model (A10~A15). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus. To adjust the brightness,contrast and gamma of thescreen PICTURE COLOR TRACKING SETU...

Page 12 - Press the MENU Button, then the main menu of the OSD appears.

A11 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the ...

Page 13 - Main menu; To adjust the brightness of the screen.; Set your own red color levels.; COLOR

A12 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues d...

Page 14 - To adjust the clearness of the screen.

A13 MENU : Exit : Decrease : Increase SET : Select another sub-menu On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripesvisible on the screen background.The horizontal screen size will alsochange. To adjust the ...

Page 17 - Troubleshooting; Check the following before calling for service.; No image appears

A16 Troubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power on and the power indicator blue orgreen? ● Is the power indicator amber? ● Do yo...

Page 18 - Display image is incorrect

A17 Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, verticalbars or stripes arevisible. ● Any horizontal noise appearing in anyimage or charactersare not clearlyportrayed. • Press the AUTO/SET button to automatically adjust your display image t...

Page 19 - Have you installed the display driver?; Have you installed the; The screen color is

A18 Troubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor,Plug&Play (VESA DDC)monitor found"message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with yourdispla...

Page 20 - Specifications; Information in this document is subject to change without notice.

A19 A19 Specifications W1942T/W1942TQ NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play PowerConsumption Dimensions & Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord 19 inches (48.14 cm) Fla...

Page 23 - 9 inch monitor; Indicator; LED Color

A22 Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 123456789 1011121314 *15 **16 640 x 350720 x 400640 x 480640 x 480800 x 600800 x 600832 x 624 1024 x 7681024 x 7681152 x 8701152 x 900 1280 x 10241280 x 1024 1440 x 9001440 x 9001440 x ...

Page 24 - Installing the Wall mount plate; Kensington Security Slot

A23 Installing the Wall mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mountplate is purchased. Kensington Security Slot Connected to a l...

Page 25 - Digitally yours