LG 206-4071P - Manuals

LG 206-4071P – Manual in PDF format online.

Manuals:

Manual

Manual LG 206-4071P

Summary

Page 2 - P A G E 2; Installer Overview; Operating Installer Menu; You will need an; LG Installer remote; control similar to the one; MPI

206-4071 P A G E 2 Installer Overview This is the commercial mode setup guide only. For all otherinformation refer to the separately-supplied TV Owner’s Manual(Users guide). Operating Installer Menu To set up the controls for the TV you will need to know how to enterthe TV Installer menu and make ch...

Page 3 - P A G E 3; References; marily by qualified electronics technicians.; Table of Contents; For Customer Support/Service please call:

P A G E 3 Use this page as a reference to find pages or sections to go to and set up the TV features. Go to page 6 to begin the Commercial Mode Master TV setup. 1. Connect TV to RF signal source.2. Customize TV features and set up other operational controls in the Installer’s menu.3. Copy the Master...

Page 4 - Typical Installer Multi-Brand Remote Control; LG Multi-brand Remote Control; Installing Batteries in Installer Remote Control; • Remove the battery compartment cover on the back side by; P A G E 4

206-4071 Typical Installer Multi-Brand Remote Control LG Multi-brand Remote Control Use the MODE button to select TV and put installer remote into TVoperating mode.Notes: This remote is supplied with the TV. This typical LG multi-brandremote control is shown for reference. See next page for typical ...

Page 5 - Installer Remote Control Typical Key Functions; P A G E 5

TV INPUT/INPUT Select available input sources. POWER Turns your TV or any other programmed equipment On or Off, depending on mode. MULTI Selects RGB, HDMI,DVI, HDMI2 and Component Input sources. Adjusts picture brightness. EZ PIC Selects the factory preset picture appropriate for the viewing environ...

Page 6 - P A G E 6; Commercial Mode Setup for Master TV; WXYZ

206-4071 P A G E 6 Commercial Mode Setup for Master TV This page provides an overview of the TV configuration. See the pages listed below for morespecific, detailed instructions at each step; how to access and use the Installer menu etc. Note 1: Disconnect all Aux inputs. Under certain conditions, E...

Page 7 - Turn to the next page to continue Cloning Setup.; Master TV; Cloning Connections/Learning Setup; P A G E 7

Before you begin cloning... • The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channeland connected to power. (See above.) • Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer ca...

Page 8 - Learn Setup from Master TV; P A G E 8; LT2002 Clone Programmer Communication Problems; Learning the Master TV Setup; Cloning Learning Setup

Use MPI Cable to Connect LT2002 Clone Programmer toMaster TV MPI Port If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote. Learn Setup from Master TV Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,POWER, or ENTER to...

Page 9 - P A G E 9; Disconnect TV Power for 15 Seconds; Teaching the Master Setup to Another TV; Connections for the LT2002 to Teach another TV the Master Setup; Cloning Connections/Teaching Setup

P A G E 9 206-4071 Teach Master TV’s Setup to the target TV After learning is complete, remove the M.P.I. cable from themaster TV and connect it to the target TV that you want tocopy the master TV’s setup into. With “THE CLONE HASCONTROL OF TV” message displayed, press 2 or use eitherChannel key to ...

Page 10 - Installer Menu

Use the Installer’s Menu to set up or change operational settings.See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installer’s Menu Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remotecontrol. Just press MENU repe...

Page 11 - Note 1: Dependent on item 093 RJP Available setting.

Menu Item Function Value Range Default Value Brief Description of Function and Comments 035 COMPPORT EN. 0 / 2 1 Set to 0 to disable HDMI 1. Set to 1 for DTV, set to 2 for PC. 038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component Video input jacks. 039 REAR AUX EN 0 / 1 1 Set to 1 to enab...

Page 12 - Detailed Descriptions of Installer Menu Items; 00 - INSTALLER SEQUENCE

P A G E 1 2 Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWERMANAGE function is for savin...

Page 13 - * Only affects Function Menu if enabled by some PPV providers.

P A G E 1 3 206-4071-D 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the on-screen menus with the display front panel—MENU, SELECT, and Left /Right arrow keys do not function. If set to 0, those keys do function. NOTE: The menus can always be accesse...

Page 16 - Reference: Clonable Menu Features; Audio; Clonable Menu Features; Option

P A G E 1 6 206-4071 Reference: Clonable Menu Features Note: Video Menu and other feature settings are not clonable on all TVs. End user has access to EZPicture, EZ Sound and Ratio on user remote control. Menu /Sub Menu Features Setup SET ID Audio Audio Language EZ SoundRite EZ sound BalanceTreble B...

Page 17 - Editing/Adding Channel ICONs and/or Labels; XYZ; N E T W O R K

P A G E 1 7 206-4071-C Changing a Channel’s ICON onMaster TV 1. With Channel Up/Down, select the channel you want to change the Icon for. 2. With the Right or Left ADJ arrow, select the letter ‘I’ on the channel ID display. 3. With the Up or Down arrow, select the desired ICON you want to appear to ...

Page 18 - LG Installer remote control; Reference: Detailed Information For Making A Master TV; Detailed Instructions

206-4071 IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how toenter the TV Installer menu and make changes tothe default values as required. If necessary, famil-iarize yourself with the TV Installer menu and how to make and save change...

Page 19 - Procedure for Checking Software Version; Reference: Checking Software Version

P A G E 1 9 206-4071 Procedure for Checking Software Version The software version of the TV may be checked by accessing the INSTALLER MENU. To do this, press the MENU buttonrepeatedly until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", ...

Page 20 - TV Camport Auto Sense Operation

P A G E 2 0 206-4071 TV Camport Auto Sense Operation The CAMPORT Auto Sense function is enabled when:1. Installer Menu Item 34, CAMPORT EN is set to 1 AND2. Installer Menu Item 40, AUTO CAMPORT is enabled (1). Selectable= Can be accessed with INPUT key, direct access, etc.Auto Sense= Switches to thi...

Page 21 - TV Aux Input Configuration / Troubleshooting; Troubleshooting; Some quick and easy tips to resolving problems; Symptoms

206-4071 P A G E 2 1 TV Aux Input Configuration / Troubleshooting Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Possible Solution(s) See Page(s) Software Problems Cannot direct enter Channel not included in channel After 2-5-5 + MENU, only channels include...

Page 22 - Power

P A G E 2 2 206-4071 Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Possible Solution(s) See Page(s) Power No Power. See troubleshooting flow chart. 24 Display Panel Picture No Picture. • Display panel is turned off. -Turn TV on. -Power failure? • Antenna/Cable not connect...

Page 23 - Problem; Reference: Cloning Procedure Troubleshooting

P A G E 2 3 206-4071 Reset Clone After Static Shock After replacing exhausted batteries, or if the programmerbehaves strangely after a static shock, use a paper clip or simi-lar instrument inserted through the small hole marked ”RESET”to activate the internal reset switch and restore normal opera-ti...

Page 24 - Troubleshooting Flow Chart

P A G E 2 4 206-4071 Controller Quick Check Is 'STATUS' LED on Analog Board Blinking ? Plug into AC Power Outlet Is TV Connected to AC Power ? Bad TV Yes No No Yes Is Red LED on TV Lit ? 1. Bad Analog Board.2. Bad Digital Board. No Cycle the power by removingand re-connecting the ACpower cord. Obser...

Page 25 - Commercial Mode Check

P A G E 2 5 206-4071 Commercial Mode Check Press the "On/Off" key on the front panel. The On/Off key is always operational. Did you get a response ? Bad TV Yes No Did TV stop responding or continue to respond ? TV is in Commercial Mode. Stopped responding TV is not in Commercial Mode Call Te...

Page 26 - Reference: RJP Mode Configuration

206-4071 Reference: RJP Mode Configuration P A G E 2 6

Page 27 - Glossary of Terms; A list of definitions for some of the words found in this guide

P A G E 2 7 206-4071 7 5 O H M R F C A B L E The wire that comes from an off-air antennaor cable service provider. The end looks likea hex-shaped nut with a wire stickingthrough the middle. It screws onto theAntenna/Cable threaded jack on the back ofthe TV. 3 0 0 TO 7 5 O H M A DA P T E R A s ma l l...

Page 28 - For Customer Support/Service Please call:

For Customer Support/Service Please call: 1-888-865-3026 www.lgcommercial.com © Copyright 2008, LG Electronics U.S.A., Inc. 206-4100 Issue* Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632