LG 1302-REV00 - Manuals - manualsarea.com

Page 2 - Safety Precautions; CAUTION; Installation; WARNING

2 Safety Precautions Safety Precautions Please take note of the safety instructions to prevent any potential accident or misuse of the product. y y Safety precautions are given in two forms, i.e. Warning and Caution as detailed be-low. WARNING: Failure to follow the instructions may cause serious in...

Page 4 - PREPARATION; Accessories

4 PREPARATION PREPARATION Accessories Check the accessories provided with the product.The picture may be different from the actual product. Accessories are subject to change without prior notice in order to improve the perfor-mance of the product. New accessories may be added or old ones may be remo...

Page 5 - INSTALLATION; How to fix anchors and screws; Drilling hole

5 INSTALLATION INSTALLATION How to fix anchors and screws CAUTION y y Check the wall materials and the thickness of finishing materials. y y You can use the anchors and bolts provided with the Laser Display set for walls made from concrete, lightweight concrete, soft fieldstone, hard fieldstone, bri...

Page 6 - NOTE

6 INSTALLATION Installation Procedure (Stand Type) 1 Install the guide pins at the bottom of the set. 2 Connect the connection rod to the Ez bracket main unit and place it on a table, without the fixed components, at the center of the screen. NOTE y y Do not assemble the fixed components to the unit...

Page 11 - Wall; Mark on wall

11 INSTALLATION 14 Mark the end of Ez bracket rod on the wall. (Mark the positions of the holes where the Ez brackets will be fixed.) 15 Remove the Laser Display set and Ez bracket from the table. 16 16 Position both holes of the fixed component against the marks on the wall and mark the positions w...

Page 16 - If the screen is not parallel to the wall; If the screen does not stay leve

16 INSTALLATION If the screen is not parallel to the wall NOTE y y If the top of the screen is tilted to the wall, add space steels at the top and, if the bottom of screen is tilted to the wall, add magnets at the bottom to make the screen parallel to the wall. If the screen does not stay leve l If ...

Page 17 - Edge Adj button on the remote control. (Press

17 INSTALLATION * If the screen is tilted to the right as shown below, fix the left bracket screw to a higher hole or fix the right bracket screw to a lower hole. 26 Refer to the screen adjustment steps to align the image from the Laser Display to the screen. 27 Complete fine tuning by pressing the ...

Page 18 - Edge Adj button on the remote control and select Reset.; Adjust the projection to fit within the screen; If the projection is too large; To move the projection to the left; To move the projection to the right

18 INSTALLATION Ez Bracket Adjustment Guide1. Reset projection * Press the Edge Adj button on the remote control and select Reset. (Select Settings → OPTION → Edge Adj → Reset to reset the position of the projection.) ? OPTION ︿ • Language• Caption : Off • Pointer• Set ID : 1 • PJT Mode : Fr...

Page 19 - Adjust the left and right widths of the projection

19 INSTALLATION Insert the hex wrench into the hole as illustrated (left) and turn it clockwise to move the pro- jection to the right. CAUTION y y If you are using a paper screen, align the paper screen with the projection and reattach it to the wall rather than moving the projection to the left or ...

Page 20 - Adjust the horizontal line of the projection to be; To turn the projection clockwise

20 INSTALLATION 4. Adjust the horizontal line of the projection to be parallel with the width of the screen 1 To turn the projection clockwise Turn the left control panel counterclockwise and turn the right control panel clockwise. 2 To widen the left width of the projection and narrow the right wid...

Page 21 - Adjust the top and bottom widths of the

21 INSTALLATION 5. Adjust the top and bottom widths of the projection so they are equal 1 To narrow the top width of the projection and widen the bottom width Turn the left and right control panels counterclockwise simultaneously. A B * Length A = Length B 2 To widen the top width of the projection ...

Page 22 - Enlarge the projection to fit the screen size

22 INSTALLATION 6. If the projection is rectangle-shaped, 1 Enlarge the projection to fit the screen size Insert the hex wrench into the hole as illustrated (left) and turn it clockwise to enlarge the size of the projection. 2 To move the projection to the left Insert the hex wrench into the hole as...

Page 23 - When the projection is the same size as the

23 INSTALLATION 7. When the projection is the same size as the screen, fine-tune the projection location using Edge Adj function * Complete fine tuning by pressing the Edge Adj button on the remote control. (Press the MENU button on the remote control and select Edge Adj in OPTION.) ? OPTION ︿ • La...