Legacy Car CD Player - Manuals

Page 2 - CONTENTS

2 CONTENTS Installation .....................................................................................................3 DIN Front-Mount (Method A) ..................................................................................3 Installing the unit .............................................

Page 3 - INSTALLATION; function of the driver.; Installing the unit

3 INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use o...

Page 4 - Removing the unit; Insert fingers into the groove in the front

1 3 4 5 2 2 5 4 1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Screw (5 x 25mm) 5. Screw 6. Strap Be sure to use the strap to secure theback of the unit in place. The strap canbe bent by hand to the desired angle. 7. Plain washer Removing the unit 1. Frame 2. Insert fingers into the groove in the fro...

Page 5 - HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL); Keep front panel into the case.; REMOVING THE FRONT PANEL

Front Panel Release Button 5 HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL) 1. Press the release button and pull-off the front panel. Keep front panel into the case. 2. To install the front panel, insert the panel into the housing and make sure the panel is properly installed, otherwise, abnor...

Page 6 - FOR 2 X 7W SYSTEM; WIRING CONNECTION; unconnected and isolated.

6 WIRING CONNECTION FOR 2 X 7W SYSTEM WIRING CONNECTION FOR 4 X 7W OR 2 X 25W SYSTEM Note:1. For 2-speakers system, green, violet, white/black and grey/black wire leads are unconnected and isolated. 2. For 2-speakers system, keep the fader control at center position to maintain the existing volume l...

Page 7 - OPERATION; GENERAL OPERATION; PWR; Press; REL; Press

7 OPERATION GENERAL OPERATION • ON/OFF Press PWR button (1) to turn on the unit. Press it again to turn it off. • FACEPLATE RELEASE Press REL button (2) to detach the removable faceplate. • LOUDNESS Press LOU/RND button (8) shortly to reinforce the bass output. 22 21 20 16 6 4 17 9 7 15 1 2 5 19 18 ...

Page 10 - RADIO OPERATION; • BAND

RADIO OPERATION • BAND Press BND button (10) to change bands as below: • SELECT STATION Rotate TUNING knob (11) clockwise or anticlockwise to adjust the frequency upward or downward. • LOCAL/DISTANT Press the LOC/RPT button (12) to select between local setting for reception of strong station and dis...

Page 11 - CD OPERATION

CD OPERATION • DISC PLAY Gently insert a compact disc with the label side facing up into the disc slot (16).The disc is then automatically loaded into the unit and starts playing with the first track of the disc. The digital display will indicate the track number and the time of the track. • EJECT P...

Page 12 - SPECIFICATION; GENERAL

SPECIFICATION GENERAL P ower Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 163 (D) x 50 (H) mm Tone Controls- Bass (at 100 Hz) : +10 dB / –10 dB - Treble (at 10 KHz) : +10 dB / –10 dB Maximum Output P ower- Version V : 7W x 4 (ch) or 25W x 2 (ch) - Low Power Versi...

Page 13 - TROUBLE SHOOTING; Symptom

88-C1133-00 13 TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problemspersist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on. connect...