Lanzar VBD1800 - Manuals - manualsarea.com

Page 2 - CONTENTS

2 CONTENTS Installation .....................................................................................................3 DIN Front-Mount (Method A) ..................................................................................3 Installing the unit .............................................

Page 3 - Installing the unit; INSTALLATION

3 Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts...

Page 4 - Removing the unit; Movable panel frame

4 INSTALLATION Removing the unit 1. Frame2. Insert fingers into the groove in the right side of the frame and pull out toremove the frame. (You can also remove the frame from the left side.) 3. Lever After removing the frame and when the front panel is hidden, then insert the levers supplied with th...

Page 5 - For safekeeping, store the front panel; USING THE DETACHABLE FRONT PANEL; To Detach the Front Panel; Press the left-top inside button of the

5 3. When the front panel is in State 3, press button, the front panel will slide down to State 2. Press buttonagain, the panel will slide up. When the front panel is in State 2, slide the bottom button of the front panel leftward and pull it out from the panelbracket. And the panel bracket will sli...

Page 6 - Adjusting faceplate angle:; To Reinstall the Front Panel

6 5. Do not expose the front panel to high temperatures or direct sunlight in anywhere. 6. Keep away any volatile agents (e.g. benzene, thinner or insecticides) fromtouching the surface of the front panel. 7. Do not attempt to disassemble the front panel. PANEL ANGLE ADJUSTMENT(OPTIONAL) You can adj...

Page 7 - WIRING CONNECTION; MAIN UNIT

7 WIRING CONNECTION GREEN GREEN/BLACK GREY GREY/BLACK VIOLET VIOLET/BLACK MAIN UNIT WHITE WHITE/BLACK FRONT Lch SPEAKER REAR Lch SPEAKER FRONT RchSPEAKER REAR RchSPEAKER Rch RED Lch WHITE (GREY) REAR RCA CABLE Rch RED Lch WHITE (BROWN) FRONT RCA CABLE ANTENNA CONNECTOR RED YELLOW BLACK BLUE POWER AN...

Page 8 - GENERAL OPERATION; OPERATION; Press

GENERAL OPERATION • ON/OFF Switch on the unit by pressing the left-top inside button of the back of them front panel. And the front panel will turn upside down from State 1 to State2 to State 3. When system is on, press POWER button (9) to turn off the unit. • FACEPLATE RELEASE Press button (7) to s...

Page 9 - RADIO OPERATION

9 • LOUDNESS Press BND/LOUD button (13) for several seconds to increase bass output and display will show “LOUD ON” . Press it again for several seconds to release this function. • SET THE CLOCK Press the DSP button (15), and the clock is shown on the display.Then hold down the button until the cloc...

Page 10 - CD OR OPERATION

10 When there is a disc in, press button(7), the panel will slide down.Then press EJECT button (4) to stop CD playing and eject the disc from thedisc slot (5). Press button (7) again to slide up the front panel. • SELECT TRACKS Press TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to move...

Page 11 - • PREVIEW ALL TRACKS; SCN; SHF; • On this unit, in addition to an audio

11 • PREVIEW ALL TRACKS Press SCN button (20) to play first several seconds of each track on the current disc. Press again to stop introand listen to track. • PLAY ALL TRACKS Press SHF button (22) to play all tracks on CD in random order. Press again to cancel the function. NOTE ON CD-R/CD-RW DISCS ...

Page 13 - FM; SPECIFICATION

GENERAL P ower Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 165 (D) x 50 (H) Tone Controls- Bass (at 100 Hz) : ± 10 dB - Treble (at 10 KHz) : ± 10 dB Maximum Output P ower : 4 x 60 Watts Current Drain : 15 Ampere (max.) CD PLA YER Signal to Noise Ratio : More tha...

Page 14 - TROUBLE SHOOTING; Symptom

TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problemspersist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on. connected to the car a...