Lanzar 1801D - Manuals - manualsarea.com

Page 2 - T A B L E O F C O N T E N T S; Amplifier installation

V I B E O W N E R ’ S M A N U A L — 1 T A B L E O F C O N T E N T S 1. Contents 2. Introduction 3. Features 4. Specifications 5. Amplifier installation 6.7. Features and controls 8.9.10.11. System wiring 12.13. Troubleshooting

Page 3 - N T R O D U C T I O N

Thank you for purchasing the Lanzar VIBE Class-D amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service.The VIBE Class-D amplifier has been designed using the latest in electronic technology available today. This m...

Page 4 - F E A T U R E S; POWER SUPPLIES

V I B E O W N E R ’ S M A N U A L — 3 F E A T U R E S CLASS-D DESIGN Low - frequency information for subwoofer only.High efficient power POWER SUPPLIES Stiffly regulated PWM power supplies.MOSFET switches maintain rated power over a wide range of battery voltages. LOW PASS FILTER Adjustable from 50H...

Page 5 - P E C I F I C A T I O N S; MODEL

S P E C I F I C A T I O N S V I B E O W N E R ’ S M A N U A L 4 — MODEL RMS Power, INTO 4 Ohms RMS Power, INTO 2 Ohms RMS Power, INTO 1.3 Ohms MAX Power, INTO 1.3 Ohms BRIDGE MAX Power, INTO 2 Ohms THD at 1 Watt, 4 Ohm Signal-to-Noise Ratio, below rated power output Frequency Response, at 1Watt,4 Oh...

Page 6 - M P L I F I E R; Find a suitable location in the vehicle to mount the amplifier.

V I B E O W N E R ’ S M A N U A L — 5 A M P L I F I E R I N S T A L L A T I O N 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power grou...

Page 7 - E A T U R E S A N D

V I B E O W N E R ’ S M A N U A L 6 — F E A T U R E S A N D C O N T R O L S - + R L Line Out Line Input Level Low Pass Bass Boost Min Max PWR PROT PROT Sub sonic 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18 SPEAKERS Master Bridged SlaveMode Data Link Phase shift - - R L R L Line Out Line Input Input Level Subs...

Page 8 - Line Input RCA Jacks; Variable Subsonic Filter

V I B E O W N E R ’ S M A N U A L — 7 F E A T U R E S A N D C O N T R O L S 1. Line Out RCA Jacks - The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. Now it is simple a matter of bringing one set of RCAs into the first amplifie...

Page 9 - Y S T M; SIGNAL INPUT AND BYPASS OUTPUT CONNECTION

V I B E O W N E R ’ S M A N U A L 8 — S Y S T M W I R I N G VIBE1801D - + R L Line Out Line Input Level Low Pass Bass Boost Min Max PWR PROT Sub sonic 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18 SPEAKERS Master Bridged SlaveMode Data Link Phase shift POWER 12V REM GND 40AX4 FUSES Remote TO CAR STEREO AUTO ANT...

Page 11 - Y S T E M; SUBWOOFR

V I B E O W N E R ’ S M A N U A L 1 0 — S Y S T E M W I R I N G R L Line Out Line Input Level Low Pass Bass Boost Min Max PWR PROT Sub sonic 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18 SPEAKERS Master Bridged SlaveMode Data Link Phase shift Master Slave ˄ BRIDGED SWITCH ; MASTER POSITION ˅ R L Line Out Line I...

Page 12 - Master Amp; BRIDGING TWO AMPLIFIERS

V I B E O W N E R ’ S M A N U A L — 1 1 S Y S T E M W I R I N G VIBE3200D - - R L R L Line Out Line Input InputLevel Subsonic Filter LowPass Filter Bass Boost Min Max 10Hz 40Hz 50Hz 150Hz 0 18dB .1V 2V 2V 8V Master Slave PHASE 0° 180° Remote Input sensitivity Bridged mode PROT PWR Data Link - - R L ...

Page 13 - R O U B L E S H O O T I N G; M P L I F I E R W I L L N O T P O W E R U P .

T R O U B L E S H O O T I N G Before removing your amplifier, refer to the list below and follow thesuggested procedures. Always test the speakers and their wires first. Disconnect all RCA inputs to the amplifier(s)-if hiss / noise disappears, then plugin the component driving the amplifier and unpl...

Page 14 - R O T E C T I O N L E D C O M E S O N W H E N T H E A M P L I F I E R I S P O W E R E D U P; and reset the amplifier. If the Protection LED still comes; I S T O R T E D S O U N D; This is always caused by a poorly-grounded RCA patch cord.; O U N

P R O T E C T I O N L E D C O M E S O N W H E N T H E A M P L I F I E R I S P O W E R E D U P Check for shorts on speaker leads.Check that the volume control on the head unit is turned down low.Remove speaker leads and reset the amplifier. If the Protection LED still comes on then the amplifier is f...