Page 2 - REFERENCES IN THE TECHNICAL DATA PLATE
2 REFERENCES IN THE TECHNICAL DATA PLATE For CE MARKET: Family: FSEB/EDModel: S84-EEquipment: BC84-E(A+B)7I3 For CSA MARKET: Family: FSUAModel: SU84Equipment: I3 (A+B)7I3
Page 3 - CONTENTS
16 - Warnings - Uses - Dimensions and technical sketch of the product - Conformity to the European directives on the Recycling Of Electrical And Electronic Equipment - Electrical diagram - Installation - Working - Maintenance CONTENTS EN
Page 5 - WARNINGS
18 WARNINGS - READ AND SAVE THESE INSTRUCTION before installing and using this pro- duct. We are not responsible for any damage or fire caused by the non-respect of the warnings described in this manual. - Keep this manual with you. If you sell or leave this unit in the future, the new customer will...
Page 6 - questions,contact the manufacturer; WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
19 WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING A) Use this unit only in the manner intended by the manufacturer. If you have questions,contact the manufacturer B) Before servicing or cleaning unit, switch power off at service panel and lock the s...
Page 7 - diately, EVACUATE AND CALL THE FIRE DEPARTMENT.; USES; filter and air deflector are not necessary in this case.
20 WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: A) SMOTHER FLAMES with a close-fitting lid,cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out imme- diately, EVACUATE AND ...
Page 8 - DIMENSIONS AND TECHNICAL SKETCH OF THE HOOD
Page 10 - CONFORMITY TO THE EUROPEANDIRECTIVES ON THE RE-; DECHETS D’EQUIPEMENTS ELECTRIQUES ET ELECTRONIQUES; INSTALLATION
All of our products are conforming to the following European directives: Directive 2006/95/ CE “LOW TENSION” Directive 2004/108/ CE “ELECTROMAGNETIC COMPATIBILITY” Directive 2012/19/ CE “RAEE” – “DISPOSAL OF ELECTRIC EQUIPMENTS AND ELECTRONICS” Directive 2002 / 95/ CE “RoHS” - “LIMITATION OF DANGERO...
Page 11 - ELECTRICAL DIAGRAM
Then insert into the proper plastic reinforcements. The hood-bearing stirrup can be applied by using the screws provided with the equipment. Now hook the cooker hood onto its bearing and then adjust horizontally and verti- cally the position of the appliance by acting on the special metric screws. t...
Page 12 - Working
25 UP USA POWER SUPPLY SUT69 EP EUROPE POWER SOPPLY SLT69 B ELECTRONIC CARD I GENERAL SWITCH P CONTROLS RC REMOTE CONTROLS TR transformer 12V M MOTOR L HALOGEN LAMP C CAPACITORS Working Following the functions are described attributed to the keys of the push botton: A: ...
Page 13 - WORKING; ADIO
26 WORKING Generating a new transmission code: The radio control system is provided with preset codes. Should new codes be requi- red, proceed as follows: Press simultaneously buttons: for two seconds. When Leds light on, press buttons: (within 5 seconds). Leds flashing 3 times in- dicate the proced...
Page 15 - MAINTENANCE
28 MAINTENANCE An accurate maintenance guarantees good functioning and long-lasting perfor- mance. Particular care is due to the grease filter panel. It can be removed by pushing its special handle toward the back-side of the cooker hood and turning the filter downwards so to unfasten it from its sl...
Page 19 - Ateliers La Cornue
Ateliers La Cornue 14, rue du Bois du Pont - Z.I. les Béthunes - 95310 Saint-Ouen-l’Aumône FRANCE Adresse postale : La Cornue SAS - B.P. 99006 - 95070 Cergy-Pontoise Cedex - FRANCE Tél. : +33 (0)1 34 48 36 36 – Fax : +33 (0)1 34 64 32 65 E-mail : [email protected] www.lacornue.com 90004608415 - EM 1...