Kodak I1860 - Manuals

A-61578 September 2006 3 Korean Please note that this equipment has obtained EMC registration for commercial use. In the event that it has been mistakenly sold or purchased, please exchange it for equipment certified for home use. European Union WARNING: THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVI...

4 A-61578 September 2006 Preparing the Site The Kodak i1860 Scanner is a new high speed, dual stream scanning platform which provides advanced image processing and superior throughput. The i1860 Scanner is designed to handle mixed document batches for any production scanning workflow. This manual pr...

A-61578 September 2006 5 Delivery day On delivery day:• Inspect the scanner packaging for any damage.• Move the scanner to the unpacking area.• Notify Kodak of a successful delivery. Installation day • On installation day, in addition to the Kodak Field Engineer, the following people need to be avai...

6 A-61578 September 2006 • Any combustible or corrosive atmosphere caused by volatile liquids or solvents. • Heat sources, such as windows, baseboard heating units, heat ducts, space heaters, or any heat-generating equipment. • Transmitted interference, such as that generated by electronic air clean...

A-61578 September 2006 7 Requirements Operating requirements The scanner can operate in a typical office environment under the following conditions: Temperature range: 15 to 35 ° C (59 to 95 ° F) Relative humidity : 15 to 76% (dry bulb) Static electricity — buildup of static electricity near the i18...

8 A-61578 September 2006 AC power quality and conditioning In some locations, even though recommended wiring practices have been followed, the power reaching the scanner may exhibit unstable power quality characteristics. System errors and intermittent data loss could result. Power conditioning equi...

A-61578 September 2006 9 System requirements Following is the minimum recommended system configuration to run a Kodak i1860 Scanner. NOTE: The actual performance of the system depends on the scanning application, choice of scanning parameters, and the host computer configuration. If the scanner is n...

10 A-61578 September 2006 Installation Procedures Follow the instructions for installing the 1394a (FireWire) card and the Kodak Driver Software before you connect the scanner to the host computer. If you want, Kodak Service will install the 1394a (FireWire card) in the host computer. Kodak takes no...

A-61578 September 2006 11 Installing the FireWire cable A six-pin connector is provided on the rear panel of the scanner for FireWire connectivity. 1. Plug the end of the cable with the right angle into the scanner. 2. Connect the other end of the cable into the 1394a card outlet in the host compute...

12 A-61578 September 2006 Supplies and Consumables The following supplies are available. Order them in the United States by calling DI Supply at 1-888-247-1234 or contact your local Kodak Reseller. Outside of the United States, contact your local Kodak dealer. Supplies/Consumables CAT No. Kodak Feed...

A-61578 September 2006 13 Delivery and Installation Setup The period between the placement of the order and the installation of the equipment may vary. During this time, you should prepare the installation site. This will help prevent unexpected problems on installation day NOTE: All site preparatio...

14 A-61578 September 2006 Claims process The following steps should be taken before making a claim. Outside the United States • Contact your local Kodak dealer or Kodak representative. Within the United States • Save all packing materials from the carton in question. • Do not move damaged equipment ...

A-61578 September 2006 15 Training Scanner operation and maintenance training is provided by the Kodak Field Engineer. NOTE: Training on the host application is not provided by Kodak. Supporting documentation The following documentation is available to support the Kodak i1860 Scanner: • User’s Guide...

16 A-61578 September 2006 Standard Maintenance Service Terms and Conditions Eastman Kodak Company (“Kodak”) and you, the customer (“Customer”) agree that the following terms and conditions will apply to the provision of services by Kodak for the products defined below located in the United States, H...

A-61578 September 2006 17 I. keep the site environmental ranges within the specifications set forth by the manufacturer of the relevant Product; J. provide continuous and appropriate resource availability during problem resolution. NOTE: Failure to meet these obligations may result, at Kodak’s sole ...

18 A-61578 September 2006 D. Extended Hours . Depending upon local service capabilities, available extended hour plans include 5-, 6-, and 7-day, 8-, 16-, and 24-hour options at additional cost. Kodak will use commercially reasonable efforts to provide Service outside of Agreement Hours as shown bel...

A-61578 September 2006 19 H. Depot Service (if applicable). If Kodak determines the Product is not operating consistently within manufacturer’s specifications, Kodak will instruct the Customer regarding shipment of the Product to Kodak for repair. Kodak will repair the Product and return the Product...

A-61578 September 2006 21 • seasonal hibernation (de-installation) and reactivation (re- installation); • service or parts associated with any unauthorized modifications, attachments or service; • rebuilding or reconditioning of Product;• misuse or abuse of Product; and/or• failure to follow operati...

GUIDE COVER M. DE MEYER-CMO US CD+U GRAPHIC DESIGN 05.03.06 FONTS USED IN THIS ARTWORK: WHITNEY FAMILY COLORS USED IN THIS ARTWORK: SPOT COLORS BLACK, KODAK YELLOW, KODAK RED 000000 i1860 Scanner Installation Planning Guide Eastman Kodak Company 343 State Street Rochester, NY 14650 USA© Kodak, 2006....