Page 3 - UNPACKING YOUR MITER SAW; PART; PACKAGE CONTENTS
3 UNPACKING YOUR MITER SAW WARNING: To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of power during unpacking and assembly. The cord must remain unplugged whenever you are adjusting/assembling the saw. 1. Remove the miter saw from the carton. IM...
Page 6 - Unmodified plugs and matching
6 WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power to...
Page 9 - This saw is not intended to cut fiber cement
9 ● Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of wood or other objects that contact the revolving blade can be thrown with high speed. ● Cut only one workpiece at a time. Stacked multiple workpieces cannot be a...
Page 10 - PROPOSITION 65 WARNING; Some examples of these chemicals are:; READ INSTRUCTION MANUAL:; To reduce the risk of injury, user and all bystanders
10 PROPOSITION 65 WARNING WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to: www....
Page 11 - should be performed by a qualified technician.
11 ELECTRICAL SAFETY INFORMATION ELECTRICAL SPECIFICATIONS AND SAFETY CAUTION: POWER SUPPLY AND MOTOR The A/C motor used in this saw is a universal, nonreversible type. See “MOTOR” in the “PRODUCT SPECIFICATIONS” section on page 2. To avoid electrical hazards, fire hazards or damage to the tool, use...
Page 12 - are not sure, have a certified electrician check the receptacle.
12 ● FUSES may “blow” or circuit breakers may trip frequently if: - MOTOR is overloaded – overloading can occur if you feed too rapidly or make too many starts/stops in a short time. - LINE VOLTAGE is more than 10% above or below the nameplate voltage rating. For heavy loads, the voltage at motor te...
Page 13 - attempt to assemble, install or operate the product.; PREPARATION
13 Before beginning assembly or operation of the product, make sure all parts are present. Compare parts with package contents list and diagram on page 3. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Estimated Assembly Time: 10 minutes. Tools needed ...
Page 14 - ASSEMBLY INSTRUCTIONS
14 2 1 ASSEMBLY INSTRUCTIONS WARNING: To avoid injury, do not connect this miter saw to a power source until it is completely assembled and adjusted and you have read and understood the operator’s manual. INSTALLING THE MITER HANDLE (FIG. 1) ● Thread the miter handle (E) into the hole located at the...
Page 17 - REMOVING AND INSTALLING THE TABLE; in electric shock or fire.; WARNING
17 7 REMOVING AND INSTALLING THE TABLE INSERT (FIG. 7) NOTE: The miter saw comes with the table insert already installed. These instructions are for replacing or adjusting the insert. To avoid injury: ● Always unplug the saw to avoid accidental starting. Remove all small pieces of material from the ...
Page 19 - DD
19 12 11 REMOVING AND INSTALLING THE BLADE WARNING ● Use only a saw blade diameter in accordance with the markings on the saw. ● Only use 7-1/4 in. diameter crosscut blades on this saw. Do not use blades with deep gullets. These can deflect and contact the guard, and can cause damage to the machine ...
Page 20 - The flat side of the blade
20 ● Press the arbor lock button (DD), holding it in firmly while turning the blade counterclockwise. When arbor lock engages, continue to press it in while tightening the arbor bolt securely. (Fig. 12) ● Rotate the cover plate (2) back to its original position until the slot in the cover plate enga...
Page 25 - workpiece to prevent sparking that could cause a fire.
25 KEEP YOUR WORK AREA CLEAN Cluttered areas and benches invite accidents. WARNING: To avoid burns or other fire damage, never use the miter saw near flammable liquids, vapors or gases. ● Plan ahead to protect your eyes, hands, face and ears. ● Read and understand the operator’s manual and labels af...
Page 26 - USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES; fingers out of the “no-hands zone” area marked on the saw table.; WHEN SAW IS RUNNING; A careless fraction of a second is enough to cause severe injury.
26 Never cut freehand: ● Brace your workpiece firmly against the fence and table stop so it will not rock or twist during the cut. ● Make sure there is no debris between the workpiece and the table or fence. Make sure there are no gaps between the workpiece, fence and table that will let the workpie...
Page 27 - Before freeing jammed material:
27 20 BODY AND HAND POSITION (FIG. 20) Never place hands near the cutting area. Proper positioning of your body and hands when operating the miter saw will make cutting easier and safer. Keep children away. Keep all visitors at a safe distance from the miter saw. Make sure bystanders are clear of th...
Page 28 - releasing the trigger switch, wait and confirm
28 22 21 BASIC SAW OPERATIONSTURNING THE LED LIGHT ON (FIG. 21) Press the LED ON/OFF switch (EE) to “ON” position to turn the light on. Do not stare into the light beam (not even from a distance). Staring into the light beam may result in serious injury or vision loss.The LED casts a shadow of the b...
Page 29 - BEFORE LEAVING THE SAW; from children and other unqualified users.; BB
29 23 24 BEFORE LEAVING THE SAW ● Never leave tool running unattended. Turn power OFF. Wait for all moving parts to stop. ● Make workshop childproof. Lock the shop. Disconnect master switches. Store tool away from children and other unqualified users. WARNING: To avoid injury from materials being th...
Page 30 - E BB
30 25 COMPOUND CUT (FIG. 25) A compound cut is the combination of a miter and a bevel cut simultaneously. ● Loosen the miter handle (E). Lift up the positive stop locking lever (BB) and position the table at the desired angle. Release the positive stop locking lever (BB) and lock the miter handle (E...
Page 31 - support must let the workpiece lay flat on the
31 27 28 29 CUTTING BOWED MATERIAL (FIG. 27) A bowed workpiece must be positioned against the fence and secured with a clamp (B) before cutting as shown. Do not position workpiece incorrectly or try to cut the workpiece without the support of the fence. This will cause the blade to bind and could re...
Page 37 - If you have any problem or questions concerning the power
37 SAWDUST Periodically, sawdust will accumulate under the worktable and base. This could cause difficulty in the movement of the worktable when setting up a miter cut. Frequently blow out or vacuum up the sawdust. If blowing sawdust, wear proper eye protection to keep debris from blowing into eyes....
Page 40 - WARRANTY VOID IF PRODUCT USED FOR COMMERICAL PURPOSES.
40 Printed in China The manufacturer will offer replacement parts for this product which under normal usage have proven to be defective in their manufacture or workmanship for a period of THREE (3) years from the date of initial retail purchase. This warranty is valid only to the original purchaser....
