Klipsch K S W 1 0 0 - Manuals

Page 2 - K l i p s c h S y n e r g y S e r i e s

K l i p s c h S y n e r g y S e r i e s ™ O w n e r ’s Manual & Wa rr a n t y K S W 5 0 ™ K S W 1 0 0 ™ K S W 1 5 0 ™ K S W 2 0 0 ™ K S W 3 0 0 ™

Page 4 - Dear Klipsch Synergy Series Owner:; Thank you for choosing Klipsch loudspeakers.

1 We Want Your Klipsch Product to Look andSound as Good as When it Left the Factory.Please Check Promptly for Transit Damage. Each Klipsch product is individually tested for sonic quality and inspected for superior appearancebefore it leaves the Hope, Arkansas factory. Your loudspeaker left the fact...

Page 5 - Subwoofer Placement; back wall or in a back corner.; Audio

2 Planning Your Klipsch Home Entertainment System Your new Klipsch subwoofer will enhance the performance of your home entertainment system,whether used within a two-channel audio or multi-channel home theater system. Speaker placementis important in optimizing the performance of your system. Please...

Page 6 - Klipsch Limited Warranty; degree of protection.

11 Klipsch Limited Warranty KLIPSCH, L.L.C. (“KLIPSCH”) warrants this product to be free from defects in materials and work-manship (subject to the terms set forth below). For a period of five (5) years from the date of purchase,KLIPSCH will repair or replace (at KLIPSCH’s option) this product or an...

Page 7 - and DTS

For parallel connection of subwoofer and main speaker wires (main speakers full range), connect the subwoofer wires to the secondary set of speaker terminals (speaker B) if your amplifier is soequipped. If you use your speaker B terminals, they must be internally wired in parallel with thespeaker A ...

Page 9 - Troubleshooting; • If your subwoofer has little or no output:; – Make sure that the “LEVEL” control is turned up.; Export Dual Voltage and 230 Volt Versions (T Designator on Fuse)

6 HIGH PASS This switch selects either “40 Hz” or “80 Hz” as the high pass filter frequency for your main speak-ers when your system is connected as per figure C (page 9). This diagram shows a separate pre-ampand power amp, but also applies to integrated components (such as receivers) possessing pre...

Page 12 - Operating Controls; woofer should initially be set near the frequency of this filter.

5 A combination of “HI LEVEL” and “LFE IN”/“SUB” inputs may be used. For example, if you connect your KSW subwoofer to electronics possessing an LFE output, you could use a speakercable to connect to the “HI LEVEL IN” speaker wire terminals and a shielded interconnect cable toconnect to the “LFE IN”...

Page 13 - Component Specifications

10 KSW 300 Type: 15" bass reflex, tuned port enclosur eAmplifier: 300 watts continuous into 4 ohmsAuto Power On: 2 second ON delay, 15 minute OFF delayFrequency Response: 25-120 Hz±3 dBMaximum Output: 112 dBAudio/Video Switch: +3 dB over entire frequency rangeLow Pass Crossover: Continuously var...

Page 14 - during hook up and installation.

3 How to Connect YourKSW Series Subwoofer The subwoofer should be unplugged from the AC power with the power switch in the OFF position during hook up and installation. AC Power A detachable AC power cord is supplied with your KSW Series subwoofer. Install the female endinto the recessed socket on t...

Page 15 - SAFETY WARNINGS

SAFETY WARNINGS • Do not make connections (other than the power cord of a powered subwoofer) directly to any AC electrical wall outlet. Connection should be made only to an audio amplifier or equivalent component and only as described in the “Subwoofer Installation” section. • Do not operate the sub...