KitchenAid KSGG700ESS2 - Manuals

5 Mobile Home - Additional Installation Requirements The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is n...

6 Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. IMPORTANT: If installing a range hood or microwave hood combination above the cooking surface, follow the range hood or micr...

7 Electrical Requirements IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1. This range is equipped with an electronic ignition sys...

8 Flexible Metal Appliance Connector: ■ If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, 1/2" or 3/4" (1.3 or 1.9 cm) I.D. (inside diameter), flexible metal appliance connector may be used for connecting range to the gas supply line. ■ A 1/2" (1.3 cm) ...

9 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from the range. Keep cardboard bottom under range. Do not dispose of anything until the installation is complete. 2. Remove oven racks and parts package from oven and shipping materials. 3. To remove cardboard botto...

10 4. Drill two 1/8" (3 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations. Floor Mounting Wall Mounting 5. Using the two #10 x 1 5 / 8 " (4.1 cm) Phillips-head screws provided, mount anti-tip bracket to the wall or floor. 6. Mov...

11 Make Gas Connection This range is factory-set for use with Natural gas. To use this range with propane gas, see the “Gas Conversions” section before connecting this range to the gas supply. Gas conversions from Natural gas to propane gas or from propane gas to Natural gas must be done by a qualif...

13 Verify Anti-Tip Bracket Is Installed and Engaged On Ranges Equipped with a Premium Storage Drawer: 1. Slide range into final location, making sure rear leveling leg slides into anti-tip bracket. 2. Remove the premium storage drawer. See the “Remove/ Replace Drawer” section. 3. Use a flashlight to...

14 To Replace: 1. Align the forward drawer notches with the notches in the drawer glides on both sides. Place the rear alignment tabs into the drawer glides on both sides. 2. Push the drawer in all the way. 3. Gently open and close the drawer to ensure it is seated properly on the glides on both sid...

15 To Replace: 1. Insert both hanger arms into the door. Be sure that the hinge notches are engaged in the oven door frame. 2. Open the oven door. The door should be able to open all the way. 3. Move the hinge levers back to the “locked” position. Check that the door is free to open and close and is...

16 GAS CONVERSIONS Gas conversions from Natural gas to propane gas or from propane gas to Natural gas must be done by a qualified installer. WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to ...

17 3. Remove plastic cover from gas pressure regulator cap. 4. Turn gas pressure regulator cap counterclockwise with a 5/8" (1.6 cm) combination wrench to remove. NOTE: Do not remove the spring beneath the cap. 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the ho...

19 4. Apply masking tape to the end of a 3/8" (1 cm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning the Natural gas broil burner orifice hood counterclockwise to remove. The hood will be stam...

20 4. Turn gas pressure regulator cap counterclockwise with a 5/8" (1.6 cm) combination wrench to remove. NOTE: Do not remove the spring beneath the cap. 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the solid end faces out and the marking “ Ð NG” is facing the d...

22 5. Replace the “100” hood with a “155” hood. Install the Natural gas broiler burner orifice hood, turning it clockwise until snug. IMPORTANT: Do not overtighten. 6. Place the broil burner on the broil burner orifice hood. Insert the broil burner ceramic igniter in the hole in the rear of the oven...

23 Adjust Oven Bake Burner Flame (If Needed) 1. Remove the premium storage drawer, warming drawer or baking drawer (see the “Remove/Replace Drawer” section). 2. Locate gas pressure regulator at rear of the drawer compartment. NOTE: On models with a warming drawer or baking drawer, an access cover mu...