KitchenAid KDRS467VSS04 - Manuals

5 NOTE: Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. See “Install Anti-Tip Bracket” section. ■ Gas pressure regulator ■ Burner grates ■ Burner bases an...

6 IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. ■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the right vertical su...

7 48" (121.9 cm) modelsNOTE: The following illustration is for dimension planning purposes only, and the locations and appearances of the features shown may not match those of your model. A. Optional backguard may be installed.B. 27 3 ⁄ 4 " (70.5 cm) depth with control panel* C. 35¾" (90...

8 Water Filtration System Location Requirements (on some models) For best results, do not install the water filtration system outside or in extreme hot or cold temperatures. Temperature of water supply to the water filtration system must be between 40°F (4°C) and 100°F (38°C). Do not install on hot ...

9 If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes.If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine ...

10 WARNING Electrical Shock Hazard Electrically ground range. Failure to do so can result in death, fire, or electrical shock. If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance w...

11 Gas Supply Line ■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ½" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials ...

12 INSTALLATION INSTRUCTIONS WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape, and film from range. Keep shipping pallet under range. Remove oven racks, grates, and parts package ...

13 A B C A. CenterlineB. Centerline of cutout to outside edge of anti-tip bracket C. Back wall to back of range 3. Drill two ¹⁄ 8 " (3.0 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations.Floor Mounting B A A. #12 x 1 5 ⁄ 8 " scr...

14 Electrical Connection — U.S.A. Only 30" (76.2 cm) and 36" (91.4 cm) Models WARNING Electrical Shock Hazard Disconnect power before servicing.Use a new 40 amp power supply cord.Plug into a grounded outlet.Failure to follow these instructions can result in death, fire, or electrical shock. ...

15 4-wire connection: power supply cord Use this method for: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Remove the ground-link screw from the range frame. Save the ground-link screw. Be...

16 A B A. Quick-connect elbow adapter fittingB. Quick-connect stem adapter fitting C B A A. ¼" water supply tubingB. O-ringC. Backstop Mounting ring and screw 1½" (3.8 cm) clearance If you need to release tubing: Push in collet to release tubing. With collet held in, pull tubing straight out...

17 B C D A E F A. To home water supplyB. Rear of cabinet cutoutC. Flexible codes-approved water supply line from home water supply D. ¼" to ¼" water supply union (supplied in water filter kit)E. Oven copper tubingF. Range front WARNING Explosion Hazard Use a new CSA International approved ga...

19 A B A. Front tabs and slotsB. Rear tabs and slots Electronic Ignition System Install Burner Bases and Burner Caps Install the burner base, making sure the igniter electrode is properly aligned with the base. Place burner caps on top of burner bases. If burner caps are not properly positioned, sur...

20 Check Operation of Cooktop Burners Push in and turn each control knob to LITE.NOTE: You will hear a clicking sound while the line clears.The surface burners and grill flames should light within 4 seconds. The first time a burner is lit, it may take longer than 4 seconds to light because of air in...

21 16. Check that the control console is flush with the top edge of the range. A 17. Replace the 2 screws on each side of the control console.18. Replace the control knobs.19. Replace burner grates.20. Test the flame by turning the control from LO to HI, checking the flame at each setting. Reinstall...

22 GAS CONVERSIONS IMPORTANT: Gas conversions from Natural Gas to LP Gas must be done by a qualified installer. WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person m...

23 To Convert Gas Pressure Regulator 1. Remove the access cap by using a wrench, turning the access cap counterclockwise. 2. Remove spring retainer from the cap by pushing against the flat side of the spring retainer. Look at the spring retainer to locate the “NAT” or “LP” position. Turn over the sp...

24 WARNING Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. Re-engage anti-tip bracket if range is moved. Do not operate range...

25 To Convert Gas Pressure Regulator 1. Remove the access cap by using a wrench, turning the access cap counterclockwise. 2. Remove spring retainer from the cap by pushing against the flat side of the spring retainer. Look at the spring retainer to locate the “LP” or “NAT” position. Turn over the sp...