KitchenAid KDRS407VSS03 - Manuals

6 Mobile Home - Additional Installation Requirements The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is n...

7 Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64 cm) countertop depth, 24" (61 cm) base cabinet depth and 36" (91.4 cm) countertop height. Dimensions must be met in order to ensure a flush fit to back wall. IMPORTANT: If installing a range hood or a hood liner above ...

8 Water Supply Requirements A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the steam feature. In Massachusetts, plumbing code 248 CMR 3.00 and 10.00 must be followed and a licensed plumber shall be used. If you have questions about your water ...

9 If connecting to a 3-wire system: Local codes may permit the use of a UL listed, 3-wire, 250-volt, 40- or 50-amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 10-50P plug on t...

10 Gas Supply Line ■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ½" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials ...

11 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from range. Keep shipping pallet under range. Remove oven racks, grates and parts package from inside oven. 2. Remove screws from kick plate. 3. Lift up on kick plate to release plate from shoulder screws. 4. Lay k...

12 2. Determine and mark centerline of the cutout space. The mounting bracket must be installed on the right side of the cutout. Position mounting bracket in cutout as shown in the following illustration. Measurement B: 30" (76.2 cm) ranges: 11 ⁵⁄₈ " (29.5 cm) 36" (91.4 cm) ranges: 14 ⁵⁄...

13 Electrical Connection - U.S.A. Only 1. Disconnect power. 2. Remove the terminal block cover screws and disengage mounting tabs to remove terminal block cover from back of range. 3. Add power supply cord strain relief. ■ Assemble a UL listed strain relief in the opening. ■ Tighten strain relief sc...

14 4-wire connection: Power supply cord Use this method for: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Remove the ground-link screw from the range frame. Save the ground-link screw. Be...

16 5. Connect the flexible codes approved water supply line to the range copper tubing, using a ¼" to ¼" water supply union. 6. Turn on water supply. 7. Check all connections for leaks. NOTE: No flushing or conditioning of the water filter is required prior to use. Make Gas Connection 1. Ass...

17 Level Range NOTE: Range must be level for satisfactory baking performance. 1. Place rack in oven. 2. Place level on rack and check levelness of the range, first side to side; then front to back. 3. If range is not level, adjust the leveling rods. Turn leveling rods located behind the kick plate t...

18 7. Insert the orifice tube on the front of the burner assembly into the opening at the front of the grill basin and set burner assembly into place. 8. Insert front tabs of the flame spreader into slots at the front of the grill basin, then the rear tabs into the rear slots. 9. Check the surface b...

19 Flame Height The cooktop flame should be a steady blue flame approximately ¼" (0.64 cm) high. Dual Flame Burner Single Flame Burner To Adjust Flame Height: 1. Unplug range or disconnect power. 2. Remove burner grates. 3. Remove the control knobs. 4. Open the oven door and remove the 2 screws ...

20 16. Check that the control console is flush with the top edge of the range. 17. Replace the 2 screws on each side of the control console. 18. Replace the control knobs. 19. Replace burner grates. 20. Test the flame by turning the control from LO to HI, checking the flame at each setting. Reinstal...

21 GAS CONVERSIONS IMPORTANT: Gas conversions from Natural gas to LP gas must be done by a qualified installer. LP Gas Conversion 1. Turn the manual shutoff valve to the closed position. 2. Unplug range or disconnect power. WARNING Explosion Hazard Use a new CSA International approved gas supply lin...

23 7. Replace the burner base. 8. Replace burner cap. 9. Repeat steps 2 through 8 for the remaining burners. To Convert Grill Burner (on some models) 1. Remove grill grate, wave plate, flame spreader and burner assembly. See “Install Grill Grease Trays” section for removal instructions. Set parts as...

24 3. Test the gas pressure regulator and gas supply line. The regulator must be checked at a minimum 1" (2.5 cm) water column above the set pressure. The inlet pressure to the regulator should be as follows for operation and checking the regulator setting: Natural Gas: Minimum pressure 6" (...

25 5. Before replacing the burner assembly, loosen the screw at the front of the burner and rotate the shutter so that the opening is ³⁄₈ " (9.0 mm) wide. 6. Reinstall the burner assembly, flame spreader, wave plate, and grill grate. See “Install Grill Grease Trays” section for installation inst...

26 Strip Circuits The following individual circuits are for use in diagnoses, and are shown in the ON position. Do not continue with the diagnosis of the appliance if a fuse is blown, a circuit breaker is tripped, or if there is less than a 240 +10%/-15% volt power supply at the wall outlet. Griddle...

27 Wiring Diagrams Cooktop Schematics 4 Burner Cooktop Caution : Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Power Cord L N GND G R R W W W W R BK BK BK R R R R R R BU BR Y GND Cont...

28 6 Burner Cooktop SW1 SW2 SW3 SW4 5 6 3 4 1 2 Power Cord Only To Cooktop Stand-Alone Version GND G Power Cord Griddle Spare Grill Spare Main - Harness Power Spare R W BK W R Reignition Module Cooktop Front Vi ew GND BK W BK W W BK BK R N L Control Input Electrodes Output Reignition Module R R R R ...

29 30"/36" (76.2 cm/91.4 cm) Oven Schematic for KDRS and YKDRS Models NOTES: ■ End of line tester is for manufacturing purpose only. ■ Dots indicate connections or splices. ■ Circuit shown in STANDBY/OFF mode with oven door closed. N L2 L1 W R BK R W BK Spare Cooktop Keypad User Interface Bo...