Kettler 7136-000-500 - Manuals

Assembly Begin the assembly of your table by carefully removingthe plastic wrap and all of the loose contents. Separatethe two table tops by removing the four plastic cornerprotectors and the plastic side strips. Step 1 2 Required Align footlock with stemtube. Insert drift pin. There are two footloc...

Assembly Step 2 A B C D E F 4 Required 4 Required m8 8 Required dia 16x8 4 Required m8x125 4 Required dia 25x8 8 Required End view and perspective view 4 Required Paying attention to position of wheelbase, assemblethe stemtubes to base in order shown. Insert endcaps. Assemble two wheelbase assemblie...

Step 3 Assembly Install non-locking wheels. Do not over torque; wheels should roll smoothly. Install non-locking wheels on both wheelbaseassemblies. A B C D E 2 Required m8x110 8 Required dia 16x8 2 Required 8m 9

Step 4 Assembly Install locking wheels. The grooves of wheels should face inward. Again, do not over torque; wheels should roll smoothly. Push down foot lock to lock the wheels.Install non-lockingwheels on both wheelbase assemblies. A C D E 2 Required m8x110 8 Required dia 16x8 2 Required m8 10 B

Assembly Step 6 Bolt one M8 crossbar between each wheelbase. Thiscrossbar is being assembled temporarily to create asupport base and will be removed at a later step. For outdoor tables only: slide the shimpad onto wheelbase(steps B, C, and D). The assembly thus far should match photo E. A B C D E M8...

Assembly Step 7 Insert endcap into the bottom of netpost bar. Using M6 crossbar, assemble crossbar and netpost barsto alignment struts. The netpost bar installation is repeated on the otherwheelbase assembly. Fastener quantities includeinstallation on both wheelbase assemblies. The assembly thus far...

Assembly Step 8 Screw eyelets to four Jbars. Assemble safety levers to two of the Jbars. Slide handgrip onto safety lever. Note the orientation of the slot in the safetylever and the Jbar as shown in photo E. 4 Required dia 12x6 2 Required m6 4 Required 2 Required m6x30 2 Required A B C D E F G 4 Re...

Assembly Step 9 Screw eyelets to support leg on table-top half. Repeat for second table-top half. 4 Required A B C 4 Required 3.9x13 Support Leg 15

Step 11 continued Assembly J K L Leg Step 12 Bolt locking struts to support leg. A B C D E F G 2 Required m6x49 2 Required m6 4 Required m12x6 18 Now, remove the temporary crossbarassembled in step 6. Carry out steps10-12 again for the other side.

A B Step 15 Screw sideshroud into place. Repeat installation of second shroud on opposite sidewheelbase assembly. Assembly 6 Required 3.9x25 21 3 Screws

Assembly Net Assembly Net assembly: Slide Jpin through net.. Place Jpin in designated slots. Tiestring to tension tab. Place string in slots over Jpin and netpost. Adjust net tension by adjusting tension tab. Remove protective plastic film from table surface. A B C D 22

THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THEMANUFACTURER ON KETTLER® PRODUCTS, EXCEPT THE MANUFACTURER’S LIMITED WARRANTY AGAINSTDEFECTS IN MATERIAL SET OUT BELOW: This KETTLER® Limited Warranty applies to products sold through the KETTLER® Authorized Dealer N...

25 Ordering Spare Parts When ordering spare parts, always state the full model number, spare part number, the quantity required and the serial number. Example order: Model 7136-500/spare part number 70130761/qty 1/serial number… Important: Spare part prices do not include fastening materials; if fas...

12 1 25 13 17 4 4 7 2 3 23 25 22 8 10 11 19 29 28 30 32 27 15 20 21 31 25 12 1 25 33 33 13 17 6 5 2 3 7 23 9 37 34 26 35 36 38 Spare Parts 26

Spare Parts 1 Top 2 94130117 94130125 2 Leg 2 94111138 94111129 3 Footcap 4 70130540 70130540 4 Clamp (outdoor table) 8 10128028 5 Clamp 25mm (indoor table) 4 94110341 6 Clamp 18mm (indoor table) 4 94110192 7 Support Leg 2 94111139 94111130 8 Wheelbase 2 94111142 94111142 9 Stemtube for non-locking ...

KETTLER ® International Inc., 1355 London Bridge Road, Virginia Beach, VA 23453 USA www.kettlerusa.com • E-mail: [email protected] For parts/service: call 866-804-0440 or e-mail [email protected] Docu 7 . 05 .11 ©2011 KETTLER ® All rights reserved. No part of this manual may be reproduced, stor...