Kenmore DU4080 - Manuals

- 5 - VACUUM CLEANER WARRANTY LIMITED WARRANTY FOR ONE YEAR from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE a defective product will be replaced free of charge. The Kenmore brand is used under license. Direct all claims for warranty serv...

- 6 - PARTS AND FEATURES It is important to know your vacuum cleaner’s parts and features to assure its proper and safe use. Review these before using your vacuum cleaner. REPLACEMENT PARTS To order a replacement part, call 1-877-531-7321 (US) / 1-844-608-3081 (CA). Item Part No.(US) Part No.(CA) Fo...

- 7 - PARTS AND FEATURES Flexible Hose Wand Release Button Upholstery Tool On/Off Switch Accessory Storage Connection Hose 3-in-1 Combination Tool Handle Wand Suction Control Carrying Handle Dust Cup Release Button Dust Cup Exhaust Filter Cover (HEPA Media Exhaust Filter Inside) Motorized Nozzle Bru...

- 8 - 1. Insert the handle into the wand until you hear a ‘click’. To remove: Press handle release button and pull up on handle. 2. Insert the wand into the main body until you hear a ‘click’. 3. Insert one end of the flexible hose into the main body as shown until you hear a ‘click’. Insert the oth...

6. Lock power cord plug onto the power cord. - 9 - 4. Insert the combination tool and the upholstery tool onto the accessory storage posts located on the back of the main body. WARNING Electrical Shock and Personal Injury HazardWrapping the cord too tightly with excessive stress on the cord may caus...

UPRIGHT MODE NOTE: Make sure the vacuum cleaner is completely assembled and the dust cup is empty before using. Do not operate vacuum cleaner without filters in place. 1. Release the handle by placing foot on the nozzle and pull back to change handle position. 2. Turn on the vacuum cleaner by pressi...

UPHOLSTERY TOOL The upholstery tool can be attached to the end of the handle and the wand. Slide the collar of the tool into the open end of the handle or wand. Use the upholstery tool for cleaning fabric surfaces such as fabric sofa and bedsheets. See ATTACHMENT USE TABLE (page 15). To return the c...

1. Press the dust cup release button to remove the dust cup from the main body. 3. Position dust cup area of vacuum over a waste receptacle. Press down on the dust release button to open dust cup lid and allow contents to drop into waste receptacle. 2. Remove any clogs that might be located in the s...

3. Clean pre-filter by gently tapping over a trash container. Tap on several sides to ensure best cleaning. 4. Reinstall the dust cup into the main body. See installation instructions in the EMPTYING DUST CUP (page 18). The pre-filter is located inside the dust cup. Clean the pre-filter as needed to...

5. Insert the exhaust filter cover tabs into the upper slots and lock the exhaust filter cover into place by pressing the lower part of the cover until a click is heard. NOTE: Make sure the exhaust filter cover is properly installed. 3. Wash with cold water only. DO NOT use detergent or soap. Allow ...

- 22 - BRUSHROLL CLEANING To maintain efficient cleaning, the brushroll must be kept free of carpet fiber, string, or hair build-up. If the brushroll is jammed, unplug and turn vacuum cleaner over and check brushroll for fiber and hair build- up. Use scissors to remove any build-up entangled around ...

CHECKING CONNECTION HOSE FOR CLOGS 1. To separate the body from the nozzle, press the motorized nozzle release pedal with foot and lift up the body. 2. Check and remove any clogs in the connection hose. 3. Reattach the nozzle onto the vacuum body. - 23 - 2. Release the wand from the body and make su...

PROBLEM POSSIBLE CAUSE SOLUTION Vacuum cleaner won’t run. Unplugged at wall outlet. Plug in firmly, press the On/Off switch to “I” or “II” position. The On/Off switch is not pressed to start the vacuum cleaner. Press the On/Off switch to “I” or “II” position. Defective wall outlet. Check with a good...