Kenmore 64182- Manuals

Page 2 - SUBJECT; „eed; SERVICE or PARTS for your Kenmore; be ready to give the; Model number; Record Coin Box; DRYER SAFETY; danger; A WARNING; instructions are not followed.; PRE-INSTALLATION REQUIREMENTS; Tools and Materials Required for Installation:

Contents Product Record SUBJECT PAGE Pre-Installation Requirements...................................... 2 For Sears warranty information or to contact a Sears Service Electrical Requirements................................................ 3 Center, call 1-800-4-my-HOME (1-800-469-4663) Exhaust Syst...

Page 3 - ELECTRICAL REQUIREMENTS; Typical 3-wire installation; EXHAUST SYSTEM REQUIREMENTS; WARNING; Do

ELECTRICAL REQUIREMENTS ELECTRICDrver CIRCUIT - Individual 30 annp. branch circuit fused with 30 annp. tinne delay fuses or circuit breakers. Use separately fused circuits for washers and dryers, and DO NOT operate a washer and a dryer on the sanne circuit. POWER SUPPLY - 3 wire, 240 volt, single ph...

Page 4 - GAS SUPPLY REQUIREMENTS

ià WARN ING I Exceeding the length of duct pipe or number of elbows allowed in the “MAXIMUM LENGTH" charts can cause an accunnulation of lint in the exhaust systenn. Plugging the systenn could create a fire hazard, as well as increase drying tinnes. ià WARNING Do not screen the exhaust ends of t...

Page 5 - UNPACKING; Â CAUTION; To change the direction of the door opening:; SIDE VIEW; KNOCKOUT

ROUGH-IN DIMENSIONS UNPACKING 1. Using the four shipping carton corner posts (two on each side), carefully lay the dryer on its left side and rennove foann shipping base. Â CAUTION I To prevent dannage, do not use the control panel or coin nneter housing as a nneans to pick up or nnove the dryer. Yo...

Page 7 - ik WARNING; iàDANGER; ALL

ELECTRICAL INSTALLATION GROUNDING REQUIREMENTS Before proceeding with electrical installation, install the dryer's coin-nnetering systenn (when used) in accordance with the separate instructions provided with the nneter. ELECTRIC Drver ALL ELECTRIC Dryers ik WARNING The following are specific requir...

Page 8 - ELECTRICAL CONNECTIONS

ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM ELECTRIC Drver Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. Install a U.L. listed strain relief into the power cord entry hole of the mounting bracket. Finger ...

Page 9 - NEVER TESTFOR GAS LEAKS WITH AN OPEN FLAME.; METER CASE INSRUCTIONS; COIN BOXADJUSTMENT

INSTALLATION Lint Blade Retaining Pin Location and Orientation 1. GAS CONNECTION (Gas dryers only) a. Remove the shipping cap from gas pipe at the rear of the dryer. NOTE: DO NOT connect the dryer to L.R gas service without converting the gas valve. An L.R conversion kit must be installed by a quali...

Page 10 - FIGURE 2; Lug; iently; FIGURES; Screws

REPLACING NYLON TIMING CAMS ON ACCUMULATOR MECHANISM WARNING I Electrical Shock Hazard • Disconnect both power supply cords from the electric power supply before making these changes. • Change timing cams before completing electrical connection. Failure to do so could result in electrical shock or p...

Page 11 - block; from coin slide; I I I m i l; □ D I M M

Pull coin slide out of coin chute (see FIGURE 4). STEP 4 Turn coin slide upside down and rennove screw that holds coin receiver block (see FIGURE 5). (1) Receiver B lock S crew FIGURES S pare P arts C om partm ent and S crew STEPSRemove coin receiver block from coin slide (see FIGURE 6 ): • Turn coi...

Page 12 - Change coin sizing; FIGURED; Replace; coin receiver; STEPS; REPLACEMENT PARTS; À CAUTION

To remove block-out keys, pull straight up. NOTE: Be sure block-out keys and /or dime inserts are seated properly and ratchet dog is in place with irs spring connected (see FIGURE 8). Be sure the proper coin sizing block is in place. Ratchet D og and pring B lock-O ut Keys FIGURES Change coin sizing...

Page 13 - Meter Case Parts List; ■ra; Timer Assembly; ITEM; Additional

Meter Case Parts List à _ I ■ ■ Hfl^H 0 ^B ■ ■ M Timer Assembly Mode! 50-1232-9 ■ra iM , >/3s«tÂ Timer Assembly Model 50-1223-10 ITEM PART NUMBER DESCRIPTION 1 50-61-13-2 Timing motor, 115VAC, 1/180RPM 2 51-161-4 Timing cam, 4-PIN (45 Minutes)* 3 00-6164 Switch Additional 51-161-1 Timing cam,1-PI...

Page 14 - V8 Coin Chute Parts List; • S’r’rrsfY; MODtl

V8 Coin Chute Parts List • S’r’rrsfY yi.NO . ^ au-’-N i;"'- »l^VN ‘-■’.'iS'' L --M.L'Cîr: ■•aü: ftv: iij'» i!- \ ( ' 0{j\ ‘ W ' > .'IPS'! :17; V 8 Parts L ist ’X . DESCRIPTION REQ. 20-3020 20-3000 1 S C R E W (M E T R IC ) 2 0 0 -9 7 2 4 0 0 -7 9 2 4 2 S C R E W (M E T R IC ) 2 0 0 -7 9 3 8 0...

Page 15 - NEW VEND PRICE; To change vend price, detach and mail the lower portion to:; SEARS COMMERCIAL DRYER WARRANTY; LIMITED; -YEAR WARRANTY ON MECHANICAL AND ELECTRICAL PARTS; IL; exhaust requirements for this washer; Notes

NEW VEND PRICE To change vend price, detach and mail the lower portion to: Customer Service Department Greenwald Industries Inc. 212 Middlesex Ave. Chester, CT 06412 The coin chute has been pre-set at the factory. When increasing in $.25 pricing Follow product information instructions; no extra part...

Page 16 - Your Home; in your home; Our Home; Sears Parts & Repair Service Center; Para pedir servicio de reparación

Get it fixed, at your home or ours! Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replace...