Kenmore 625.347001- Manuals

5 -- STEP 1: INSTALL COLD WATER SUPPLY SADDLE VALVE -- Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak- tight connection to the RO 1/4” tubing (see FIG. 8, page 8). A typical connection, using the included saddl...

6 -- STEP 2: INSTALL DRAIN ADAPTER -- J Note: Running the drain tubing directly to a floor drain, sump, standpipe, laundry tub, etc., as shown on page 18, is preferred. However, if that is not pos- sible or practical, the included drain adapter installs in the sink drain pipe, always above or ahead ...

7 -- STEP 3: INSTALL FAUCET (cont.) -- B. ASSEMBLE FAUCET1. If not already assembled, install the rubber washer, spacer, flat (or lock) washer and hex nut onto the threaded faucet stud. 2. Apply Teflon tape to the end of the faucet stud. Turn the tubing adapter with a blue collet onto the stud and h...

8 -- STEP 5: INSTALL STORAGE TANK, MAKE REMAINING TUBING CONNECTIONS -- 1. CONNECT DRAIN TUBING, FAUCET TO DRAIN ADAPTER: Referring to FIG. 8, run the loose section (connected to faucet barb fitting) of black 3/8”tubing from the faucet to the drain adapter, with a black collet, installed on page 6. ...

9 -- STEP 6: SANITIZING, PRESSURE TESTING & PURGING -- SANITIZING Sanitizing is recommended upon installation of the RO system, and after servicing inner parts. It is im- portant for the service person to have clean hands while handling inner parts of the system. CAUTION: Be sure to remove the R...

10 -- HOW YOUR REVERSE OSMOSIS SYSTEM WORKS -- PREFILTER Water from the cold supply pipe enters the RO as- sembly prefilter first (FIG. 8 and schematic below). The prefilter has a replaceable sediment cartridge with activated carbon in its composition. The car- tridge (10 micron) removes sand, silt,...

11 -- CARE OF YOUR REVERSE OSMOSIS SYSTEM -- To keep your reverse osmosis system operating and making high quality water, you must make sure sup- ply water is always within the limits shown in the specifications. Good supply water helps to assure longer life from the RO membrane cartridge, prefilter...

12 -- CARE OF YOUR REVERSE OSMOSIS SYSTEM -- 2. Press inward while turning the RO cap to the left ( ? ) to remove from the bracket/membrane housing. 3. Use a pliers, or heavy wire made into a hook, to pull the RO cartridge from the housing. Note: Sanitizing is recommended after servicing in- ner par...

13 -- CARE OF YOUR REVERSE OSMOSIS SYSTEM -- TUBING CONNECTION (continued) If tubing is used, other than supplied with the sys- tem, be sure it is of high quality, exact size and round- ness with a smooth surface. To Disconnect Tubing: Push the collet inward and hold with a finger while pulling the ...

14 -- CARE OF YOUR REVERSE OSMOSIS SYSTEM -- REVERSE OSMOSIS SYSTEM CARE GUIDE MODEL NO. 625.347001 1. AT LEAST every 6 months, replace the prefilter and postfilter cartridges. Clean or replace the flow control and screen. 2. Replace the RO membrane cartridge when the percent rejection of total diss...

15 -- DIMENSIONS and SPECIFICATIONS -- 16” 16” 9”dia. 15” STORAGE TANK Metric Supply water pressure limits . . . . . . . . . . . . . . . . . . . . . . . . 40 --- 125 psi 280 --- 860 kPa Supply water temperature limits . . . . . . . . . . . . . . . . . . . . . 40 --- 100 ° F 5 --- 40° C Maximum total...

17 -- REPAIR PARTS -- Kenmore Reverse Osmosis Drinking Water System, Model No. 625.347001 Key No. Part Number Description of Part 1 7205350 Faucet 2 7207920 Adaptor, 7/16”-24 x 3/8”Tubing 3 7185788 Screw, #10-12 x 5/8”(8 req.) 4 42-34702 RO Membrane Cartridge 5 7177175 O-ring Seal, 1-7/8”x 2-1/8” 6 ...

18 -- REMOTE LOCATION FOR REVERSE OSMOSIS SYSTEM -- RO product water faucet COLD WATER SUPPLY 1/4” green tubing 3/8” blue tubing STANDPIPE airgap airgap SUMP airgap LAUNDRY TUB FLOOR DRAIN OPTIONAL DRAIN POINTS FOR REJECT WATER REMOTE RO INSTALLATION (storage tank not shown) Possible remote location...

part no. 7208112 (4/99) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. OWNER’S MANUAL MODEL NO. 625.347001 The model number of your reverse osmosis system is found on the rating decal. This decal is on the top of the bracket. When requesting service or ordering parts, always provide the fo...