Kenmore 30'' Chimney Range Hood- Manuals

Page 2 - TABLE OF CONTENTS; FOR DOMESTIC COOKING ONLY; READ AND SAVE THESE INSTRUCTIONS; SAFETY INSTRUCTIONS

2 WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufac- turer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cl...

Page 3 - OPERATION; Oper; KENMORE LIMITED WARRANTY

3 CONTROLS This hood is operated using (5) pushbuttons on the front of the hood canopy. The fan OFF pushbutton turns the fan off. The fan low, medium and high speed pushbuttons turn the fan on to three different speed settings. The light pushbutton turns the lights on and off. OPERATION Safety Clean...

Page 4 - MOTOR; PARTS INCLUDED WITH HOOD; * Parts Not Included With Hood” are available by

4 TOOLS NEEDED FOR INSTALLATION Screwdriver (Flat & Phillips) Pencil Tape Measure Drill Sabre Saw Keyhole Saw -or- Duct Tape Wire Stripper PARTS NOT INCLUDED WITH HOOD* CLEANING Proper maintenance of the Range Hood will assure proper performance of the unit. MOTOR The motor is permanently lubric...

Page 5 - EQUIVALENT DUCT LENGTH CHART

5 EQUIVALENT DUCT LENGTH CHART Broan Model 401 Straight Duct 3¼-in. x 10-in. x 2-ft. long Equivalent length 2 ft. Broan Model 406 Straight Duct 6-in. round x 2-ft. long Equivalent length 2 ft. Kenmore Model 59581 3¼-in. x 10-in. to 6-in. Round Transition Equivalent length 5.5 ft. Broan Model 428 3¼-...

Page 6 - INSTALL THE DUCTWORK; 63⁄4” = bottom of hood 24” above cooktop

6 WARNING To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use...

Page 7 - INSTALL UPPER FLUE MOUNTING BRACKET; INSTALL THE WIRING

7 INSTALL UPPER FLUE MOUNTING BRACKET W arranty Safety Cleaning Oper ation Installation Service P ar ts 1. If a framing member is not present, drill two 5 ⁄ 16” diameter holes where shown. Insert dry- wall anchors into the holes. 2. Center the bracket over the hood location and flush with the ceilin...

Page 8 - Note: Damper flaps must be removed and discarded; INSTALL DUCT CONNECTOR

8 1. Place range hood body on its back, with controls facing up. Place cardboard under hood to protect countertop or table finish. 2. Position the curved plate glass over the range hood body as shown. 3. Install rubber bushings into all (4) holes of the glass.4. Place a plastic decorative washer ont...

Page 9 - INSTALL THE HOOD (HORIZONTALLY DUCTED HOODS ONLY); ” ROUND

9 Cleaning Oper ation Installation Service P ar ts INSTALL THE HOOD (HORIZONTALLY DUCTED HOODS ONLY) 1. DO NOT REMOVE the protective plastic film covering the decorative flues at this time. 2. Make sure there will be adequate clearance between top of hood and lower flue mounting bracket for ductwork...

Page 10 - INSTALL THE HOOD (VERTICALLY DUCTED HOODS ONLY)

10 6” ROUND DUCT (VERTICAL DUCTING) 5. Measure and cut metal ductwork. Set ductwork aside. 6. Plug hood power cord into the outlet. 7. Remove the upper flue from inside the lower flue. Install the lower flue bracket to the lower flue using (2) flue bracket screws (#8 x 3/8”). Ensure that the bracket...

Page 11 - ts

11 W arranty Safety Cleaning Oper ation Installation Service P ar ts Note: Purchase Non-Duct Kit, Kenmore part number 59921. 1. CAUTION: Use only expandable aluminum duct provided with non-duct kit. 2. Do not remove the protective plastic film covering the decorative flue at this time. 3. Remove dam...

Page 12 - KEY PART NO. DESCRIPTION

12 SERVICE PARTS 9 1 7 8 15 12 16 14 5 6 2 10 11 4 3 13 17 Models 233.5992*, 5993** = color number INSTALL FLUE EXTENSION FOR 9-FT. CEILINGS Note: 9-ft. ceilings require the purchase of a flue extension, Kenmore part number 59920. 1. Discard the upper flue (supplied with the hood) and replace it wit...