Kathrein CAP 210 - Manuals

5 • Turntable with fi tted BAS 60 and ready for connection cables with a length of 3.5 m • Power supply cable (10 m) for connection to on-board network • Mounting plate • Roof duct with sealing gasket • Sika fl ex® 291 sealing glue (100 ml tube) • UFD 170 satellite combi receiver with connecting cab...

6 Proper use The MobiSet 3 digital CAP 310 is designed to receive digital TV and radio programs via satellite. The turntable is intended for the Kathrein planar antenna BAS 60. This antenna can be used to receive digital TV and radio signals in the frequency range from 10.70 to 12.75 GHz; the antenn...

7 Safety instructions - important notes When carrying out installation work in locations with a risk of falling, take appropriate safety precautions, e.g. use of a working platform. Make sure that the vehicle roof is suf fi ciently strong and stable to carry out the installation work (risk of damage...

8 Fundamental information A crucial safety factor is proper performance of installation and electrical connection work, and the speci fi ed alignment of the turntable in the direction of travel (park position), see also installation and connection.Heed as precisely as possible the installation condi...

9 Operate the system from your vehicle‘s battery (12 V) or a suitable mains power pack. This mains power pack must guarantee a stable initial voltage of 12 V, 11 A continuous current and 15 A (300 ms) surge current.The transient power consumption is up to a maximum of 12 A. To ensure reliable functi...

10 Safety instructions - important notes Instructions for installation and operation of the HDP 171 with the UFD 170 1. The turntable can only be used in conjunction with a Kathrein UFD 170 Caravan Digital Combi Receiver or a Kathrein UFD 540 Caravan Digital Receiver with HDS 160 control unit. 2. To...

12 Installation and connection Required tools and equipment • Circular cutter, Ø 38 mm• Flat-bladed screwdriver for M5 screws• Drilling machine• Galvanised tallow drop screws, depending on roof structure (Ø: 5 mm, sheet metal screws D 7981, depending on roof panel structure) or tallow drop screws D ...

14 Installation and connection Installation steps Installation of cable duct and mounting plate Note: If you have previously used a Kathrein HDM140/141 fl exible satellite mast or another mast with a diameter of 34 mm, you can continue using the existing duct hole in the roof (if space allows). • In...

17 Installation and connection Installation of turntable Version with cable duct below turntable (Fig. E) • Check that the O ring is correctly positioned in the groove of the cable duct (Fig. A). An incorrectly positioned or missing O ring will allow water to penetrate. • Feed the ends of the cables...

19 Installation and connection Brief instructions for installing the HDP 171 The sequence of pictures shown illustrates all the necessary installation steps that are required to assemble the HDP 171 turntable and the BAS 60 planar antenna on the roof of the vehicle. The other detailed instructions i...

20 Set up electrical connections. Connect UFD 170/UFD 540 receiver. Connect connecting/control unit to battery. Installation and connection The antenna must always be lowered into horizontal position (park position) while driving! Maximum driving speed of the vehicle: 130 km/h Installation of UFD 17...

22 Installation and connection Connecting the HTV 115 LCD TV Set Connect a HTV 115 and the receiver with the included cinch/cinch cable included with the UFD 170. Make sure that you heed the colour identi fi cation of the connectors and outlets on the back side of the receiver. Connect the TV with t...

23 Connection example motorhome - 12 V battery connection (UFD 170) Installation and connection Attention: For operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the UFD 170 combi receiver. Non-compliance means...

24 Connection example caravan - 230 V battery connection (UFD 170) Installation and connection Fig: H 8-pole 6-pole brown white green Note! Do not connect.Option not available.The antenna must be lowered before departure.• Turn on receiver• Select HDP menu• Select park function and confirm Mains uni...

25 BAS 60 planar antenna Proper use The BAS 60 fl at antenna is used to receive digital TV and radio signals in the frequency range from 10.70 to 12.75 GHz. It cannot receive terrestrial signals. The BAS 60 has been designed for mobile use, to receive satellite signals in stationary caravans, motorh...

26 BAS 60 planar antenna The footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which satellite reception is possible. The transmission power is at its greatest in the centre of this spot – it becomes progressively weaker moving outwards.Yo...

27 Polarisation setting Polarisation setting As supplied, the BAS 60 is mounted centrally on the turntable. In this position, you can also receive signals from satellites with deviations in the degree of longitude (of the typical reception range) of between 15° and 20° from the orbit position of the...

28 We strongly advise that users who are not familiar with the installation work should not reassemble the BAS 60 independently. They should contact a technician or engineer. They may fi nd a suitable person on the campsite. Make sure that: - The antenna and connected units are disconnected from the...

31 Dismantling for servicing If repairs to the system or individual components are necessary, contact your specialist dealer or our service centre (see below for address). Never open the turntable yourself! Dismantling • The cables may not be cut! • Disconnect the power, coaxial and data cables from...

32 Technical data Dimensions (mm) Driving direction

33 Technical data Electric data Supply voltage 10.9…13.8 V Ignition signal 12…24 V “Standby” current 20 mA “ENGINE ON” current 5...8 A Transient start-up current 12 A Azimuth rotation range 0…370° Elevation rotation range 10…90° Search time for fi rst satellite (typ.) 10…120 s Search time for additi...

Declaration of conformity 936.2712/B/0306/ZWT - Technical data subject to change. Internet: www.kathrein.deKATHREIN-Werke KG • Anton-Kathrein-Strasse 1 - 3P.O. Box 100 444 • 83004 Rosenheim GERMANY