JVC XA-A50CL - Manuals

Introduction Thank you for purchasing the JVC product. Before you begin operating this unit, please read this operating instructions carefully to be sure you get the best possible performance. If you have any questions, consult your JVC dealer. CAUTION: This unit is compatible with WMA-DRM. When you...

Accessories Check the supplied accessories after unpacking. CD-ROM USB 1.1 cable Cable clip

Features What is Digital Audio Player XA-A50CL? XA-A50CL is an Ear-Clip headphone type Digital Audio Player, which creates a high quality sound reproduced by the 30 mm diameter Neodymium driver unit in an innovative design shell. You can store the music files-MP3 (up to about 30 files) or WMA / WMA-...

About this instruction Configuration of this instruction This instruction is configured with the following 4 sections: The screens used in this instruction are from Windows XP. The screens and procedures explained may differ depending on your PC. Also, software images for explanation may differ from...

Parts Identification 1. (Stop/Play/Power) button 2. Operation indicator Lights: When setting up the unit Flashes 2 times every 5 seconds: During playback Flashes every 2 seconds: During pause 3. (Skip) buttons 4. (Volume) buttons 5. button 6. USB port cover 7. Battery cover 8. Ear hook 9. Ear pad

About Voice Guidance Digital Audio Player has Voice Guidance system, which informs you the operational information of the Digital Audio Player. For example, when you press (next) button while listening to the music, you will hear "Next" through the Digital Audio Player to confirm the operati...

Preparation Driver installation (For Windows 98SE user ONLY) When using Windows 98SE, install the USB driver for accessing the Digital Audio Player. 1. Connect the Digital Audio Player to your PC using the supplied USB cable. Check "CD-ROM" for the driver selection on the dialog. 2. Load the...

Selecting the language for the Voice Guidance You can change the language of the guide voice by selecting the guide voice files stored in the supplied CD-ROM. The initial language is set to English. 1. Load the supplied CD-ROM on your PC. The language selection screen appears. 2. Click the desired l...

Putting the battery 1. Slide open the battery cover. 2. Insert the alkaline battery, matching the + and - . Press in on - end first and down on + end. 3. Close the battery cover. About changing the battery The battery should be changed when the operation indicator fades or does not turn on. Change t...

Basic Operation Transferring the music files into the Digital Audio Player In this instruction, the file-transferring procedure is explained using the Windows Media Player. CAUTION: This Digital Audio Player is compatible with WMA-DRM. When you transfer the files other than the following files and f...

To connect to your PC 1. Open the USB port cover of the right headphone. 2. Connect the Digital Audio Player to your PC using the supplied USB cable. The operation indicator of the Digital Audio Player starts flashing. 3. Press to permit the access to the Digital Audio Player from the PC. When press...

Putting on the headphones 1. Open the Ear Hook outward slightly. 2. Put the Ear Hook on your ear and adjust the Ear Hook position to fit your ear. 3. Close the Ear Hook. NOTE: Stretching the ear hook on the headphone too wide from its original position may result in damage to the ear hook.

Turning on the power 1. Press and hold from 2 to 5 seconds to turn on the Digital Audio Player. The Operation indicator lights up and the Digital Audio Player is turned on, then the playback starts. When the playback position is memorized, playback starts from the memorized position. (See "To st...

Adjusting volume 1. Press . : Increases the volume with a high beep sound. : Decreases the volume with a low beep sound. When pressing and holding the button, the volume is changed continuously with a single beep sound. NOTES: When activating Voice Guidance system, the volume adjustment does not tak...

Basic playback To stop playback 1. Press . The playback is stopped with the current position of the playback memorized, then the Digital Audio Player is turned off 10 seconds later. When pressing and holding for 2 seconds, the Digital Audio Player turns off without the memory of the current position...

Advanced Operation Playing back with playlist You can make up to three playlists to customize the playback files you want to. Using a playlist, you can edit the playback files and their order. NOTE: When the music file listed in the playlist does not exist on the Digital Audio Player, the step is sk...

To switch a playlist 1. During playback with a playlist, press and hold until the desired playlist is selected. To turn off the playback with a playlist, press and hold until "Playlist off" is heard.

Various effects and setting You can add various effects to the music sound and changing the basic setting using the button. NOTE: There is a time limit in doing the following procedures. If you do not press any button about 10 seconds, the mode setting is canceled after setting the current item and ...

1. Press repeatedly to select the desired item. Each time you press the button, the item changes as follows: 2. Press repeatedly to select the setting. 3. Press . Without pressing the button for 10 seconds, the setting is finished ("Complete" is heard.) and playback starts. Play mode setting...

Troubleshooting Connection Transfer Playback Symptom Cause Action The PC cannot detect the Digital Audio Player. Your PC may work incorrectly. Restart your PC, then connect the Digital Audio Player again. Your PC needs the access permission from the Digital Audio Player. Press after connection. For ...

Specification Design and specifications subject to change without notice. Memory type: 128 MB Flash memory Playable files: MP3, WMA, WMA-DRM (copyright-protected) Headphones driver unit: 30 mm diameter Neodymium Power supply: AAA alkaline battery (DC 1.5 V) x 1 Battery life: approx. 20 hours (Playba...