Page 2 - IMPORTANT SAFEGUARDS; ers or aerosol cleaners. Use a damp cloth for cleaning.
E-2 IMPORTANT SAFEGUARDS PORTABLE CART WARNING (symbol provided by RETAC) S3126A 1. Read all of these instructions.2. Save these instructions for later use.3. All warnings on the product and in the operating instructions should be adhered to.4. Unplug this appliance system from the wall outlet befor...
Page 4 - FOR USA AND CANADA; CAUTION; Information for USA; Safety Precautions
E-4 FOR USA AND CANADA CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS I N S I D E . R E F E R S E RV I C I N G T O QUALIFIED SERVICE PERSONNEL. The lightning flash wish arrowheadsymbol, within an equilateral triangle isintended to alert the use...
Page 5 - CONTENTS; INTRODUCTION
E-5 Thank you for purchasing this product.(These instrustions are for TK-C1480U, TK-C1480E and TK-C1481EG)Before beginning to operate this unit, please read the instruction manualcarefully in order to make sure that the best possible performance is obtained. CONTENTS INTRODUCTION Features .............
Page 6 - Features; Characters and symbols used in this instruction manual.
E-6 A new DSP (Digital Signal Processor)features a Extended Dynamic Range(ExDR) and enables to shoot both brightand dark locations. The use of a new CCD with a SENSE UP( X 3 2 ) f u n c t i o n r e a l i ze d t h e m i n i mu mluminous flux density for subject of 0.8 lx(F1.2, 50%, AGC 20dB) and 0.02...
Page 7 - Operating Precautions
E-7 ● To save energy, when it is not being usedturn the system’s power off. ● This camera has been designed for indooruse. When you use it outdoor, be sure touse a housing and the like. ● Do not install or use the camera in thefollowing places.• In a place exposed to rain or moisture.• In a place wi...
Page 8 - Lens mount; b y t u r n i n g i t; Camera-mounting bracket; Be sure to use a 6 mm long screw.; Controls, Connectors and Indicators
E-8 INTRODUCTION 1 Lens mount This means to attach the lens.This is applicable to both the C-mountlenses and CS-mount lenses. 2 Backfocus adjustment ring Adjusting the back focus during lensinstallation.When readjustment is required, loosent h e l o c k i n g s c r e w 3 b y t u r n i n g i t counte...
Page 9 - Cover; When the button is pressed, a menu
E-9 ON SIMPLEX ONLL SET AWC MENU CAMERA SETUP EXT TERM-OFF INT/GL DUPLEX RX TERM-OFF NOT USED VIDEO DC IRIS # $ @ ! %^&* 0 9 8 8 Cover The cover opens if it is pulled to the leftwhile being pushed. 9 [VIDEO/DC] Iris Selector Switch This is set according to the type of lenswhen an automatic iris ...
Page 10 - right Button; terminates at 75; NOT USED
E-10 INTRODUCTION 13 [ , , , ] Up-and-down, left-and- right Button These buttons select items on the menuscreen and change a set value.( Page 23) 14 [EXT.TERM-ON/OFF] Terminal On/OffSwitch of External SynchronizationSignal This is a terminating ON/OFF switch forthe external synchronization input sig...
Page 11 - To input DC 12V or AC 24V power.; signal connection terminals; ON the EXT.TERM switch; Signal
E-11 DC12V AC24V Y/C OUT SYNC IN POWER VIDEO OUT SEE INST- RUCTION MANUAL + - 1 2 CLASS 2 ONL Y(U TYPE) ISOLA TED PO WER ONL Y (E TYPE) TX + TX - RX + RX - AUX GND A B C D ⁄ ) ( fi › ¤ ‹ 19 [DC 12V, AC 24V] Power input terminals(TK-C1480U and TK-C1480E) To input DC 12V or AC 24V power. 20 [TX+ A , TX...
Page 12 - CONNECTION/INSTALLATION; System with up to 8 cameras; MEMO; • Confirm switch settings on the screen as follows.; Confirm that the image from the camera to be checked
E-12 REC PLAY FF REW REVERSE PAUSE/ STILL REC CHECK STOP/EJECT COUNT/CLOCK TIMEMODE TIMER REC AL/PLRESET MENU VIDEO CASSETTE RECORDER SHIFT/TRACKING SET/V.LOCK RESET /CANCEL OPERATE SR-L910 OPE. LOCK 1 TO CAMERA TO CAMERA DATA I / O DATA I / O RX RX + RX RX - TX TX + TX TX - COM COM 1 2 3 4 5 6 7 8 ...
Page 13 - Connecting the control signal cable; switch on the power again.; Setting on the MENU screen (; MACHINE ID setting switches; When connecting
E-13 CAMERA SETUP SET MENU EXT TERM-OFF INT/GL DUPLEX RX TERM-OFF NOT USED ON LL SIMPLEX ON EXT TERM-OFF INT/GL DUPLEX RX TERM-OFF NOT USED ON LL SIMPLEX ON VIDEO DC IRIS AWC A RX + B RX C TX + D TX TX + A TX B RX + C RX D TX + A TX B RX + C RX D RM-P2580 Camera 2control signalconnection terminals C...
Page 14 - Monitor; Procedures
E-14 CONNECTION/INSTALLATION SET MENU CAMERA SETUP EXT TERM-OFF INT/GL DUPLEX RX TERM-OFF IOT USED ON LLSIMPLEXON VIDEO DC ALC LEVEL Av Pk L H DC12V AC24V CLASS 2 ONL Y(U TYPE) ISOLA TED POWER ONL Y (E TYPE) TX + TX - RX + RX - AUX Y/C OUT SYNC IN POWER VIDEO OUT GND A B C D SEE INST- RUCTION MANUAL...
Page 15 - Mounting the lens; Attached 4 pin plugs
E-15 Mounting the lens VIDEO DC IRIS VIDEO DC 3 4 2 1 Mount the lens according to the procedures described below. Attached 4 pin plugs 1. Before mounting a lens, check whetherit is a C-mount or CS-mount lens.To change the mounting method, loosenthe back-focus locking screw (M 2.6)using a Phillips he...
Page 16 - Connections on the back; Power supply
E-16 DC12V AC24V CLASS 2 ONL Y(U TYPE) ISOLA TED POWER ONL Y (E TYPE) TX + TX - RX + RX - AUX Y/C OUT SYNC IN POWER VIDEO OUT GND A B C D SEE INST- RUCTION MANUAL 1 + - 2 Connect the DC 12 V or the AC 24 V powersupply to the DC 12V/AC 24V terminals. Top r eve n t c o n n e c t i o n e r r o r s o r ...
Page 17 - • Genlocking is not possible with a signal
E-17 Control signal cables These cables should be connected only whenit is required to control the camera using theRS-442A or RS-485 signals. The use of 0.654-conductor twisted pair cables is recom-mended. With these cables, the maximum ex-tension distance is 1,200 m. Connect to the otherside in pai...
Page 18 - Mounting the camera; Fall Prevention; • E x e r c i s e m a x i m u m c a u t i o n w h e n
E-18 DC12V AC24V CLASS 2 ONL Y(U TYPE) ISOLA TED POWER ONL Y (E TYPE) TX + TX - RX + RX - AUX Y/C OUT SYNC IN POWER VIDEO OUT GND A B C D SEE INST - RUCTION MANUAL + - 1 2 2mm 6mm M3 x 6mm MAX. 7 mm Mounting the camera CONNECTION/INSTALLATION Camera mountingscrew Camera-mounting bracket Rotation pre...
Page 19 - Fixing screws; Installation of camera; • Mounting from the bottom
E-19 VIDEO DC IRIS VIDEO DC IRIS Camera-mounting bracket Fixing screws Installation of camera • Mounting from the bottom This camera is originally designed to bemounted from the bottom, as shown q . The hole is standard photographic pan-head screw size (1/4-20 UNC). Examplethe Fixing unit or Pan/Til...
Page 20 - Lens adjustment; • LEVEL adjustment; Monitor screen; Too bright; • If the sensitivity adjustment LEVEL is; ALC adjustment
E-20 CONNECTION/INSTALLATION Lens adjustment ALC LEVEL Av Pk L H Connect the camera according to the connection method, turn it on, display an image on themonitor, and check the image. The camera has been factory-adjusted to the best position, butit may need to be adjusted according to the object co...
Page 21 - • With a fixed-focus lens; Back focus adjustment; Lens focus ring; Tighten
E-21 Back focus adjustment • With a fixed-focus lens If the focus can not be adjusted correctly byrotating the lens focus ring, adjust the backfocus as follows. 1. Loosen the back focus locking screw byturning it counterclocckwise ( ) with a screwdriver. 2. Shoot a pattern closely. 3. Turn the lens ...
Page 22 - Auto white balance control adjustment; Error message display; AWC button
E-22 CONNECTION/INSTALLATION Auto white balance control adjustment Each light source has its own colour temperature. Therefore, when the main light sourcelighting an object is changed, the white balance should be adjusted again by pressing theAWC button. 1. Place a white object under the samelightin...
Page 23 - MENU SETTING; Setting the menu; The MENU screen is displayed.; MENU button
E-23 MENU SETTING Setting the menu CAMERA SETUP SET MENU EXT TERM-OFF INT/GL DUPLEX RX TERM-OFF NOT USED CAMERA SETUP SET MENU ON LL SIMPLEX ON VIDEO DC IRIS AWC 1. Press the MENU button. The MENU screen is displayed. 2. Set the cursor (>) to a desireds u b - m e n u u s i n g t h e , button. 3. ...
Page 24 - The flow of menu screen; The word “COLOUR” is displayed as “COLOR” on the TK-C1480U.
E-24 ME N U S Y N C A D J U S T V I D E O A D J U S TMOD E E S L E C T A L C S E T T I NGS C OMMUN I C AT I ON F A C TOR Y S E T T I NGS MOT I ON D E T E CT S Y NC D A J U S T V P HA S E 0 H P HA S E 0 S C E COARS 0 S C F I NE 1 2 8 DE V I O AD J U ST WH T E B A L E A T W NC A I C O OUR L E N ORMAL ...
Page 26 - SYNC ADJUST Screen
E-26 Item Functions and set values Initial value V PHASE H PHASE SC COARSE SC FINE This adjusts the vertical synchronization to those of other cameraswhen a selector switch for the synchronizing system on the sideis at LL. (50Hz (60Hz) power region only. ( ): TK-C1480U)When it is not set to LL, “---...
Page 27 - The ExDR does not function.; NORMAL
E-27 Item Functions and set values Initial value SHUTTER(ExDR) * When the SHUTTER (ExDR) item is set to NORMAL, the following items (SHUTTER SPEED, FAST LIMIT, ExDR LEVEL, and M.ExDR SPEED)cannot be changed. SHUTTERSPEED This sets the electronic shutter as well as the ExDR (ExtendedDynamic Range).Th...
Page 28 - Item
E-28 ALC SETTINGS Screen (Continued) MENU SETTING Item Functions and set values Initial value FAST LIMIT ExDRLEVEL M.ExDRSPEED AGC MODE LOLUX MODE SENSE UP This sets the fastest value of a shutter speed when AUTO is set.The MANUAL, M. ExDR, A. ExDR set value is displayed as “- - -” andcannot be chan...
Page 30 - VIDEO ADJUST Screen
E-30 Item Functions and set values Initial value WHITEBALANCE COLOURLEVEL ENHANCELEVEL PEDESTALLEVEL AUTOBLACKCTL Selects the white balance adjustment function. The whitebalance can be adjusted manually or automatically forlight within the colour temperature range of 2500K to8000K.• ATW: Auto-Tracki...
Page 31 - MODE SELECT Screen; MOTION DETECT Screen
E-31 MODE SELECT Screen Titles, image reversion, etc., are set. Item Functions and set values Initial value CAMERATITLE EDIT REVERSEMODE ALM.TITLESIZE ALARMCOLOUR D.ZOOMMAX Bring up the CAMERA TITLE, EDIT screen.( Page 36) Settings are executed for image reversion.OFF: Image does not reverse.R-L: Le...
Page 32 - LEVEL
E-32 Item Functions and set values Initial value LEVEL AREA EDIT ALARM TIME DEMONSTRATION NORMAL – 10s – MENU SETTING MOTION DETECT Screen(Continued) This sets the level that detects motion.If the item MODE is set to OFF, “- - -” will appear, andsettings cannot be changed.To function with large sign...
Page 33 - COMMUNICATION Screen
E-33 Item Functions and set values Initial value FACTORYSETTINGS Set values are returned to initial values. The values set on the menu are returned to initial values.CANCEL : No return to the initial value. CLEAR : Returns set values except titles to the (WITHOUT TITLE) initial value. CLEAR (ALL) : ...
Page 34 - BLC EDITTING Screen; The EDIT1 screen is brought up.; Press the SET button.; * To use the set metering area, set the item
E-34 BLC EDITTING Screen MENU SETTING It is possible to set freely the light metering area for backlight compensation. The 2 screensof EDIT1 and EDIT2 can be set. CAMERA SETUP SET MENU AWC L A C S E T T I N GS I I R S L E V E L NORMAL A E V R A GE : P E AK 8 2 : S U T H T E R E x DR ) ( N RMAL O P I...
Page 35 - Manual Adjustment of White Balance; screen appears on the monitor.; VIDEO ADJUST screen; SET button; The word “COLOUR” is displayed as “COLOR” on the TK-C1480U.
E-35 Manual Adjustment of White Balance When automatic adjustment of the white balance results in a “reddish screen”, etc., adjust thewhite balance manually. 1. Set the WHITE BALANCE item on theVIDEO ADJUST screen to AWC andpress the SET button.* The WHITE BALANCE adjustment screen appears on the mo...
Page 36 - The screen returns to MODE SELECT.; CAMERA TITLE Setting
E-36 1. Select the item CAMERA TITLEon the MODE SELECT screen,and push the SET button. Then, the CAMERA TITLE screen isbrought up. 2. Select the first character from thecharacter area using buttons. The selected character is displayedflashing on and off. 3. Push the SET button. The first character g...
Page 37 - Setting the MOTION DETECT Function; MOTION DETECT screen; The setting screen is brought up.; * It is possible to check and confirm the set
E-37 Setting the MOTION DETECT Function It is possible to set freely the area where MOTION DETECTING functions. T I MO O N DE T EC T M O E OF F D L E E L N ORMAL V A R A E D I T E A L RM T I E M 1 0 s A D E O N S TR A T I N O M . . . . MOTION DETECT screen flash lights gray flash Setting screen 1. S...
Page 38 - OTHERS; Installing the ferrite core; Pass the lens cable through the ferrite core twice and con-; Wind twice; Specifications
E-38 OTHERS Installing the ferrite core To retain electromagnetic compatibility, use the ferrite cores provided when connecting to the lens orthe power source. VIDEO DC IRIS ALC LEVEL Av Pk L H Notes: Install the ferrite cores within 50 mm of the camera-side connectors. (Fasten the ferritecore with ...
Page 40 - COLOUR
VICTOR COMPANY OF JAPAN, LIMITED TK-C1480, TK-C1481 COLOUR VIDEO CAMERA is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD. is a registered trademark in Japan, the U.S.A., the U.K. and many other countries. © 2001 VICTOR COMPANY OF JAPAN, LIMITED Printed in ThailandSC961006H-007 ® ®
JVC RV-NB20B
User Manual
JVC HX-Z30
User Manual
JVC MX-GT80
User Manual
JVC AV-48WP30
Manual
JVC HR-S3911U
User Manual
JVC HD-52Z575
Manual
JVC AV-27F702
Manual
JVC GR-DV500U
User Manual
JVC HR-A591U
User Manual
JVC AV-36320
Manual
JVC XV-S200BK
Manual
JVC SP-EXA1
User Manual
JVC AV-36D303
Manual
JVC FS-SD770
User Manual
JVC AV-56WP74
User Manual