JVC RX-D302B - Manuals

3 Front panel 1 STANDBY/ON button and standby lamp (14) 2 CC CONVERTER button (16) 3 SETTING button (17, 19) 4 ADJUST button (23) 5 SURROUND button (33) 6 Source lampsDVD MULTI, DVR/DVD, VCR, DBS, TV, USB, FM, AM 7 • SET button (17, 19, 23)• TUNER PRESET button (28) 8 • SOURCE SELECTOR (14, 28)• MUL...

4 Putting batteries in the remote control Before using the remote control, put two supplied batteries first. 1 Press and slide the battery cover on the backof the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–). 3 Replace the cover. If the range or effe...

5 Snap the tabs on theloop into the slots ofthe base to assemblethe AM loop antenna. Connecting the FM and AM antennas Do not connect the AC power plug to the wall outlet until all connections are completed. AM loop antenna(supplied) If AM reception is poor, connectan outdoor single vinyl-coveredwir...

6 L R LS RS SBL C SW SBR (*SB) LEFT RIGHT LEFT RIGHT LEFT RIGHT SUBWOOFER OUT SURROUND SPEAKERS CAUTION:SPEAKER IMPEDANCE 6 -16 SURROUND BACK SPEAKERS CENTER SPEAKER FRONT SPEAKERS Connecting the speakers Do not connect the AC power plug to the wall outlet until all connections are completed. Speake...

7 ı Î ‰ Ï Ì Ç Å DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT This receiver is equipped with the following video terminals—composite video, S-video, and component video terminals.• If your video components have S-video ...

10 7 Connecting a TV Connect the TV to the appropriate MONITOR OUT jacks to view the playback picture from any other connected video components. Stereo audio cable(not supplied) Red Component video cable (not supplied) TV Composite video cable (not supplied) Green Blue Red S-video cable (not supplie...

11 DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/DVD) 3(VCR) NOTES • When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components:– 1(DVR/DVD): For DVD recorder or DVD player – 2(DBS): For DBS tuner – 3(VCR): For VCR If you connect other components, ch...

12 4. Turn on the receiver, then slide the USB WIRELESSswitch on the rear to “ID LEARNING,” and select thesource as “USB WIRELESS.” When you slide the switch, the lamp in the switch startsflashing. 5. Set the volume to minimum. IMPORTANT: Always set volume to “0” when connecting or disconnecting the...

13 Now PC is ready for playback through the USB connection. After installation is completed, you can use your PC as theplayback source. The PC automatically recognizes the receiverwhenever the transmitter is connected to the PC or the USB cableis connected between the PC and the receiver while the r...

14 Basic operations 2 Select the source to play On the front panel: Turn SOURCE SELECTOR until the source nameyou want appears on the display. The source lamp corresponding to the selected source lights inred.• As you turn SOURCE SELECTOR, the source changes as follows: DVD MULTI: Select the DVD pla...

15 Selecting the digital decode mode If the following symptoms occur while playing Dolby Digital or DTSsoftware with “DGTL AUTO” selected (see page 14), follow theprocedure below:• Sound does not come out at the beginning of playback.• Noise comes out while searching for or skipping chapters or trac...

16 Basic adjustment of auto memory This receiver memorizes sound settings for each source:• when you turn off the power, and• when you change the source. When you change the source, the memorized settings for thenewly selected source are automatically recalled.The following can be stored for each so...

17 To obtain the best possible sound effect from Surround/DSPmodes (see pages 29 to 33), you need to set up the speaker andsubwoofer information after all the connections are completed.From pages 17 to 22, how to set speakers and other basic itemsof the receiver are explained. Setting the speaker in...

18 Speakers (channels) number and the size You can find how each of the speaker size is defined according tothe number of connected speakers (speaker channel “ch” number)you select.• Subwoofer is counted as 0.1 channel. The size of connected speakers CH L/R C LS/RS SB SUBWFR 2.0CH LARGE NONE NONE NO...

19 Operating procedure On the front panel ONLY: Before you start, remember... There is a time limit in doing the following steps. If the setting iscanceled before you finish, start from step 1 again. Ex.: When setting DIGITAL IN 1 terminal. 1 Press SETTING. MULTI JOG now works for the setting operat...

20 In this case, set the distance as follows: Left front speaker (L): “FRONT L <3.0m> (10ft)” Right front speaker (R): “FRONT R <3.0m> (10ft)” Center speaker (C): “CENTER <3.0m> (10ft)” Left surround speaker (LS): “SURR L <2.7m> (9ft)” Right surround speaker (RS): “SURR R <...

21 Selecting the main or sub channel—DUAL MONO You can select the playback sound (channel) you want whileplaying digital software recorded (or broadcasted) in Dual Monomode (see page 30), which includes two monaural channelsseparately. When the receiver detects Dual mono signals, theDUAL MONO indica...

23 Sound adjustments You can make sound adjustment to your preference aftercompleting basic setting. Basic adjustment items You can adjust the following items. See pages in parentheses fordetails.• You cannot select the items which is not available with the current setting. Items To do SUBWFR LVL* 1...

24 Adjusting the equalization patterns—D EQ 63Hz/250Hz/1kHz/4kHz/16kHz You can adjust equalization patterns in five frequency bands(center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for thefront speakers.• Once you have made an adjustment, it is memorized for each source. Adjustable range: –8 (...

25 Adjusting the bass sounds Reinforcing the bass—BASS BOOST You can boost the bass level—Bass Boost.• Once you have made an adjustment, it is memorized for each source. B BOOST < ON > Select to boost the bass level.The B.BOOST indicator lights up on thedisplay. B BOOST < OFF > Select to...

26 Adjusting the center channel localization for ProLogic IIx Music and Pro Logic II Music—CENTERWIDTH This setting is available when Pro Logic IIx Music or Pro Logic IIMusic is activated for the analog or digital 2-channel sound signal.To activate Pro Logic IIx Music or Pro Logic II Music, see page...

27 Tuner operations Tuning in to stations manually From the remote control ONLY: 1 Press FM or AM to select the band. The last received station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station you want is tuned in. • Pressing (or holding) TUNING 9 i...

28 3 Press the numeric buttons (1 – 10, +10) toselect a channel number while the channelnumber position is flashing. • For channel number 5, press 5.• For channel number 15, press +10, then 5.• For channel number 30, press +10, +10, then 10. 4 Press MEMORY again while the selectedchannel number is f...

29 Creating realisticsound fields Reproducing theater ambience In a movie theater, many speakers are located on the walls toreproduce impressive multi-channel sound, reaching you from alldirections.With these many speakers, sound localization and soundmovement can be expressed.Surround/DSP modes bui...

30 DTS Neo:6 DTS Neo:6 is another conversion method to create 6-channel (plus subwoofer) from analog/digital 2-channel software by usingthe high precision digital matrix decoder used for DTS-ES Matrix6.1ch.• This receiver provides the following DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 ...

31 Introducing the DSP modes The sound heard in a concert hall, club, etc. consists of directsound and indirect sound—early reflections and reflections frombehind. Direct sounds reach the listener directly without anyreflection. On the other hand, indirect sounds are delayed by thedistances of the c...

32 Using the Surround/DSP modes Available Surround/DSP modes vary depending on the speaker settings and the incoming signals. See the table below.• The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of the surround channels. For e...

33 On the front panel: Before you start, remember... There is a time limit in doing the following steps. If the setting iscanceled before you finish, start from step 2 again. 1 Select and play any source other than DVDMULTI. • Make sure you have selected the input mode (analog or digital) correctly....

34 AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III AV COMPU LINKremote controlsystem The AV COMPU LINK remote control system allows you tooperate JVC’s video components (TV, DVD player*, and VCR)through this receiver. This receiver is equipped with the AV COMPU LIN...

35 One-touch DVD play Simply by starting playback on the DVD player, you can enjoy theDVD playback without setting other switches manually.• When the DVD player is connected through the analog input jacks on this receiver (and analog input is selected), thereceiver automatically turns on and changes...

37 1 2 3 4 5 6 7 8 9 10 0 10 You can always perform the following operation: DVD/DVR : Turn on or off the DVD recorder or DVDplayer. After pressing DVR/DVD, you can perform the following operationson the DVD recorder and DVD player. 3 : Start playback. 7 : Stop playback. 8 : Pause playback. To relea...

38 By changing the transmittable signals, you can use thesupplied remote control to operate other manufacturers’products. • Refer also to the manuals supplied with the other products.• To operate those components with the remote control, first you need to set the manufacturers’ codes each for the TV...

39 ❏ Changing the transmittable signals for operatinga VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’s code using buttons1 – 9, and 0. See “Manufacturers’ codes for VCR” on the right. 4 Release VCR . Now, you can perform the following operation on the VCR. VCR : Turn on or off the...

41 Troubleshooting Use this chart to help you solve daily operational problems. Ifthere are any problems you cannot solve, contact your JVC’sservice center. PROBLEM The power does not come on. The receiver turns off (enters standbymode). “OVER HEAT” flashes on the display,then the receiver turns off...

42 Designs and specifications are subject to change withoutnotice. Amplifier Output Power At stereo operation: Front channels: 110 W per channel, min. RMS, driveninto 6 Ω at 40 Hz to 20 kHz with no more than 0.8% total harmonicdistortion. At surround operation: Front channels: 110 W per channel, min...

0205RYMMDWJEIN EN © 2005 Victor Company of Japan, Limited AUDIO / VIDEO CONTROL RECEIVER RX-D301S / RX-D302B cover_RX-D301S[J]_f.p65 05.2.22, 16:44 2

English Français LVT1321-002A [C] RX-D302B AUDIO / VIDEO CONTROL RECEIVER RECEPTURE DE COMMANDE AUDIO/VIDEO INSTRUCTIONS MANUEL D’INSTRUCTIONS cover_RX-D301S[C]_f.p65 05.2.23, 16:24 3

1 English Table of Contents Parts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4Checking the supplied accessories ........

9 English 7 Connecting a VCR Turn off all components before making connections. • When you connect other components, refer also to their manuals. Å To component video output• Connect Y, P B , and P R correctly. ı To left/right audio channel output Ç To left/right audio channel input Î To composite v...

10 English 7 Connecting a TV Connect the TV to the appropriate MONITOR OUT jacks to view the playback picture from any other connected video components. Stereo audio cable(not supplied) Red Component video cable (not supplied) TV Composite video cable (not supplied) Green Blue Red S-video cable (not...

28 English 3 Press the numeric buttons (1 – 10, +10) toselect a channel number while the channelnumber position is flashing. • For channel number 5, press 5.• For channel number 15, press +10, then 5.• For channel number 30, press +10, +10, then 10. 4 Press MEMORY again while the selectedchannel num...

29 English Creating realisticsound fields Reproducing theater ambience In a movie theater, many speakers are located on the walls toreproduce impressive multi-channel sound, reaching you from alldirections.With these many speakers, sound localization and soundmovement can be expressed.Surround/DSP m...

30 English DTS Neo:6 DTS Neo:6 is another conversion method to create 6-channel (plus subwoofer) from analog/digital 2-channel software by usingthe high precision digital matrix decoder used for DTS-ES Matrix6.1ch.• This receiver provides the following DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) an...

38 English By changing the transmittable signals, you can use thesupplied remote control to operate other manufacturers’products. • Refer also to the manuals supplied with the other products.• To operate those components with the remote control, first you need to set the manufacturers’ codes each fo...

39 English ❏ Changing the transmittable signals for operatinga VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’s code using buttons1 – 9, and 0. See “Manufacturers’ codes for VCR” on the right. 4 Release VCR . Now, you can perform the following operation on the VCR. VCR : Turn on or...