JVC AV-20NN15 - Manuals

5 TV buttons and functions The following illustrations are for AV-14FN15 and AV-20NN15 only, which are used forexplanation purposes. Your TV may not look exactly like the illustration. Front of the TV AV-14FN15 AV-20NN15 Rear of the TV AV-14FN15 AV-20NN15 No. Button/terminal Description 1 I (main po...

6 Setting up your TV CAUTION • Turn off the equipment including the TV before connecting. 1 Connecting the antenna To install rod antenna Install into the top-rear holder. Once installed, it cannot be removed. VIDEO AUDIO VIDEO -1 INPUT OUTPUT VIDEO AUDIO VIDEO -1 INPUT OUTPUT Illustration of AV-14F...

7 Setting up your TV (continued) 5 Making the initial settings Set up your TV by pressing MENU/OK button or waiting for 15 seconds, then the TV will operateby following steps as below: 7 • Press the red button to cancel the SETUP TOUR RESTART function.If you want to make initial settings againwhen t...

8 Basic setting for picture COLOR SYSTEM You can select the appropriate color system whenthe picture is not clear or no color appears. Press the COLOR SYSTEM button to select asetting. In TV mode: NTSC 3.58 MHz (Fixed) In VIDEO mode: AUTO PAL SECAM NTSC3.58 NTSC4.43 To operate this function with a m...

9 Advance setting for picture BLUE BACK You can set the TV to automatically change to ablue screen and mute the sound if the signal isweak or absent, or when there is no input froman antenna.Select the BLUE BACK in the INSTALL menu,then choose ON or OFF. ❇ MENU INSTALL BLUE BACK If you wish to conti...

10 Favorite channel and video setting To register the favorite channel You can register and recall 4 favorite channels byusing the color buttons (red, green, yellow, blue). 1 In TV mode, select a TV channel (CH02-CH69, CC01-CC125) you desired to register. 2 Press and hold a color button for 3seconds...

11 Customized setting VNR You can reduce the picture noise.Select the VNR in the PICTURE FEATURES menuunder PICTURE menu, then choose a setting ofVNR function. ❇ VNR MENU PICTURE PICTURE FEATURES OFF VNR is turned off. AUTO Effect of VNR is automatically controlled. MIN Effect of VNR becomes minimum...

12 TV channel presetting To register the TV channels auto-matically You can register the TV channels into the TV’schannel list automatically. 1 Display the INSTALL menu. ❇ MENU INSTALL 2 Choose AUTO PROGRAM, then press theMENU/OK button. 3 Press the 5 / ∞ button to select AIR or CABLE, then press th...

13 Additional preparation The illustrations shown in this section are for AV-20NN15 only, which are used for explanation pur-poses. Your TV may not look exactly the same as the illustration. Before connecting • Read the manuals provided with the devices for the proper connection. • Turn off all the ...

14 TV RF systems M Color systems TV mode: NTSC 3.58 MHzVIDEO mode: PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz Receiving channels VHF low channel (VL), VHF high channel (VH), UHF channel (U)Receives cable channels in mid band, super band and hyper band. Power requirements AC 110 to 240 V, 50/60 Hz Exte...

INSTRUCTIONS GGT0071-001A-H Contents Knowing your TV’s features ....................................................... 3 Remote control buttons and basic functions .............................. 4 TV buttons and functions ........................................................... 6 Setting up your...

2 15 cm 10 cm 10 cm 15 cm WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS TV. 1 Operate only from the power source indicated on the rear of the TV.2 Avoid damaging th...

3 Knowing your TV’s features Confirm your TV’s functions Some functions shown in this remote control may not be available for your TV.When you press a button concerned to a function that is not available for your TV, it does not work and thelogo “Ø” appears on the screen. For a function that is not ...

4 Remote control buttons and basic functions No. Press To 1 POWER Turn on or off the TV from standby mode. 2 MENU/OK Display menu and confirm selected function. 3 5 / ∞ / 2 / 3 Select and adjust menu function. 4 CHANNEL -/+ Select the desired channel number. 5 VOLUME -/+ Adjust the volume level. 6 T...

5 Remote control buttons and basic functions (continued) The following chart shows locations of functions in menus. In this manual,location of a function is described as follows: Note: Some functions have the 4th menus as the sub-menus.* To exit the menu, the on screen display will show BACK indicat...

7 1 Connecting the aerial cable. If you connect a VCR, connect the aerial output jack of your VCRand the aerial jack on the TV with the aerial cable. Then connect theoutput jacks of your VCR and the VIDEO-1 input jacks of the TVwith the video cable and audio cables. For details, see the manualof you...

8 5 Making the initial settings Set up your TV by pressing MENU/OK button or waiting for 15 seconds, then the TV will operate by following steps as below: • Press 5 / ∞ button to select AIR or CABLE, press theMENU/OK button.TV willstart searching for thechannels. AUTO PROGRAM . . AUTO PROGRAM OK CH ...

10 Adjusting the picture – USER You can adjust the desired picture setting when selecting USERin PICTURE MODE. 1 Select the USER in PICTURE MODE under PICTURE menu. 2 Select the PICTURE SETTING in PICTURE menu, then adjustthe setting. PICTURE 2 : Lower 3 : Higher BRIGHT 2 : Darker 3 : Brighter DETAI...

11 BLUE BACK You can set the TV to automatically change to a blue screen andmute the sound if the signal is weak or absent, or when there isno input from an antenna. Select the BLUE BACK in the INSTALL menu, then choose ON orOFF. If you wish to continue viewing the poor picture, cancel the BLUEBACK ...

12 Basic setting for sound BALANCE You can adjust the volume balance between the left and rightspeakers.Select the BALANCE in SOUND menu, then adjust the setting. SOUND TURBO You can enjoy the emphatic low and high frequency levels. Press the SOUND TURBO to select ON or OFF.To operate this function ...

14 To register the favorite channel You can register and recall 4 favorite channels by using the colorbuttons (red, green, yellow, blue). 1 In TV mode, select a TV channel (CH02-CH69, CC01-CC125)you desired to register. 2 Press and hold a color button for 3 seconds or more.“FAVORITE CHANNEL ■ PROGRA...

15 VNR You can reduce the picture noise.Select the VNR in the PICTURE FEATURES menu underPICTURE menu, then choose a setting of VNR function. OFF VNR is turned off. AUTO Effect of VNR is automatically controlled. MIN Effect of VNR becomes minimum level. MAX Effect of VNR becomes maximum level. If yo...

18 The illustrations shown in this section are for AV-14FT15 and AV-21YA15 only, which are used for explanation purpose. Your TVmay not look exactly the same as illustrated. Before connecting • Read the manuals provided with the devices for the proper connection. • Turn off all the devices including...