John Deere TR1072 - Manuals

S a fe t y 5 OS1048M-1072M Safety Rules (Rev. 6/11/2004) TRAINING „ Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer...

6 S a f e t y OS1048M-1072M Safety Rules (Rev. 6/11/2004) (Safety Rules continued from previous page) „ Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securelyfastened. Falling off power unit can result in deathfr o m b e i n g ru n ov e r o r c ru s h e d . K e e p ...

S a fe t y 7 5WPMAN0100 (Rev. 5/2/2008) 3 - Serial Number Plate 6 - PN 5WP20106 CONTACT WITH ROTATING PARTS CAN CAUSE SERIOUS INJURY. WARNING 15502--B ROTATING COMPONENTS Do not operate without cover in place.Look and listen for rotation. Do not open cover until all components havestopped. 4 - PN 5W...

8 S a f e t y 5WPMAN0100 (Rev. 5/2/2008) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - PN 5WP55121 7 - PN 5WP1003751 WARNING 55121--C FALLING OFF CAN RESULT IN BEING RUN OVER. „ Tractor must be equipped with ROPS (or ROPS CAB)...

D e a l e r C h e c k L i s ts 9 5WPMAN0100 (Rev. 5/2/2008) DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to becertain it is set up properly before delivering it to thecustomer. The following check list is a reminder ofpoints to ...

1 0 O p e ra t i o n 5WPMAN0100 (Rev. 5/2/2008) OPERATION The operator is responsible for the safe operation ofthis overseeder. The operator must be properly trained.Operators should be familiar with the equipment, thetractor, and all safety practices before starting opera-tion. Read the safety rule...

O p e r a t i o n 11 5WPMAN0100 (Rev. 5/2/2008) The front rollers can be angled to promote a moreaggressive tearing action of the turf. The more theangle, the more tearing action is applied by the frontroller pins. For severe turf conditions, the maximumangle position may be desired (Figure 2). Figu...

1 2 O p e ra t i o n 5WPMAN0100 (Rev. 5/2/2008) Figure 5 . Top Link Attached to Overseeder 2. Attach the tractor’s top link to the upper mast of theoverseeder. Secure with high-strength top link pinand retaining pin provided with the tractor. See Fig-ure 5. 3. Adjust top link as needed to level the ...

O p e r a t i o n 1 3 5WPMAN0100 (Rev. 5/2/2008) rollers are level. Adjust the 3-point lower lift stop so thatthe roller spikes penetrate the ground at 3/4" (19 mm)or enough to remove the tracks left by the tractor tires. Figure 8 . Flow Control Handle OPERATING TIPS Do not allow dirt to build u...

O w n e r S e r v i c e 1 5 5WPMAN0100 (Rev. 5/2/2008) OWNER SERVICE The information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available.For your protection, read and follow the safety informa-tion in thi...

1 6 O w n e r S e r v i c e 5WPMAN0100 (Rev. 5/2/2008) NOTES

P a r ts 1 7 5WPMAN0100 (Rev. 5/2/2008) OVERSEEDER DRIVE ASSEMBLY REF TR1048 TR1060 TR1072 QTY DESCRIPTION 1 ………… ………… ………… 1 Seedbox Assembly 2 ………… ………… ………… 1 Frame and Roller Assembly 3 5WP1001710 5WP1001710 5WP1001710 1 Bracket, Chain Guard 4 * 2 Screw, HHCS 5/8 NC x 1-1/2" GR5 5 5WP57817 5...

1 8 P a r ts 5WPMAN0100 (Rev. 5/2/2008) FRAME AND ROLLER ASSEMBLY

P a r ts 1 9 5WPMAN0100 (Rev. 5/2/2008) FRAME AND ROLLER ASSEMBLY PARTS LIST REF TR1048 TR1060 TR1072 QTY DESCRIPTION 1 ………… ………… ………… 1 Frame 2 5WP1000778 5WP1000778 5WP1000778 1 Roller Arm, Right Rear 3 5WP1000779 5WP1000779 5WP1000779 1 Roller Arm, Left Rear 4 5WPD2213 5WPD2213 5WPD2213 4 Bushing...

2 0 P a r ts 5WPMAN0100 (Rev. 5/2/2008) SEEDBOX ASSEMBLY

P a r ts 2 1 5WPMAN0100 (Rev. 5/2/2008) SEEDBOX PARTS LIST REF TR1048 TR1060 TR1072 QTY DESCRIPTION 1 5WP1000001 5WP1000001 5WP1000001 1 Bracket, Seedbox Support Left 2 5WP100001348 5WP100001360 5WP100001372 1 Shaft, 3/8" Square w/Holes 3 ………… ………… ………… 1 Center Stiffener 4 5WP1000766 5WP1000766...

2 2 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

A p p e n d i x 2 3 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

PART NUMBER 5WPMAN0100 ©2002 Woods Equipment Company. All rights reserved. WOODS and the Woods logo are trademarks of Woods Equipment Company. FrontierEquipment and the Frontier logo are trademarks of Deere & Company. All other trademarks, trade names, or service marks that appear in this man-ua...